HGLRC M100-5883 GPS Manual

HGLRC Ikke kategoriseret M100-5883 GPS

Læs gratis den danske manual til HGLRC M100-5883 GPS (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 5 anmeldelser. Har du et spørgsmål om HGLRC M100-5883 GPS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

HGLRC M100-5883 GPS

Manual

M100-5883 GPS

instruction manual

M100-5883 GPS

instruction manual

M100-5883 GPS

instruction manual

M100-5883 GPS

instruction manual

M100-5883 GPS

instruction manual

Parameters

Receiver Type：■GPS/QZSS L1C/A■SBAS EGNOS、GAGAN、MSAS和WAAS

■GLONASS L1OF ■BDS B1I ■Galileo E1B/C

Sensitivity: Tracking and Navigation -166DBM, re-obtain -160dbm, cold start-148dbm

The ﬁrst ﬁx¹ time: Cold start 29s, hot start 1S

Horizontal positionaccuracy²: .02 m CEP

Accuracy of Time Mai Signal: RMS 30ns, 99% 60ns

Speed precision m: 0 m/s.05

Operating limits: Interaction ≤ 4 g, altitude 80,000 m, speed 500 m/s

Frequency of time pulse signal: 1Hz

Potter rate: 9,600 -460800 BPS (default is 115200 bps)

Maximum navigation update rate: 10Hz (default 10 Hz, conﬁguration)

*The default GPS+Galileo+QZSS+SBAS, BDS and Honor are not supported at the same time

1. All satellites are ≥-130dBm

2. CEP 50%, 24 hours static, ≥-130dBm, > 6SVs

3. 50%, 30 m/s, dynamic operation

4. Assuming onboard < 4g platform

Introduction

POWERPPS

SCL

SDA

GND

Wiring diagram

SCL

SDA

GND

Connect the GPS to any port of the ﬂight controller according to the wiring diagram,

and use UART3 as a demonstration

(Note: Be sure to connect to a free serial port or a dedicated GPS serial port)

Open the conﬁguration page of INAV, set the sensor input type to GPS,

and the baud rate to 115200

Turn on GPS and enable UBLOX protocol

Compass Selection QMC 5883

Open the port page of Betaﬂight, set the sensor input type to GPS,

and the baud rate to 115200

，

Power on the aircraft, the indicator light will be on when the GPS is working

normally, and the GPS logo on the top of Betaﬂight will be on

Find UART3, turn on GPS at sensor input and select baud rate 115200

Precautions

1. After turning on the compass, please calibrate it before using it.

2. Please supply power to GPS according to the voltage within the speciﬁed range.

3. Please carefully solder according to the wiring diagram to avoid short-circuiting and burning the GPS.

4. Please use BF4.3.0 or above ﬁrmware (too low version does not recognize the 10th generation chip).

5. GPS must be installed with the antenna facing up and away from motors, power lines and other interfering parts

Turn on GPS and enable UBLOX protocol

INAV settings

Betaﬂight settings

Power on the aircraft, the indicator light is on when the GPS is working normally,

and the GPS and compass lights on the top of the inav are on

Indicator light

Normal start

Real position accuracy

PPS (red light))

normal bright

Flickering

Power (blue light)

normal bright

Company name:Guangdong Huagulong Technology Co., Ltd.

After sales email:hglrc@support.com

Oﬃcial website:www.hglrc.com

Address:8th Floor, Building C1, Juntong Industrial Park, No. 9 Jiuyuan Road, Zhushan,

Dalang Town, Dongguan City, Guangdong Province 523770,China

Compass direction

Produkt Specifikationer

Mærke:	HGLRC
Kategori:	Ikke kategoriseret
Model:	M100-5883 GPS

Har du brug for hjælp?

Hvis du har brug for hjælp til HGLRC M100-5883 GPS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret HGLRC Manualer

HGLRC M100-5883 GPS Manual

24 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025