HGST UltraStar 7K4000 Manual

HGST Harddisk UltraStar 7K4000

Læs gratis den danske manual til HGST UltraStar 7K4000 (3 sider) i kategorien Harddisk. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om HGST UltraStar 7K4000, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Page 1 version 1.0
Quick Installation Guide
HGST Ultrastar 7K 000 4
Models: HUS 4040 0 72 ALE64
S 4 0 HU 72 030ALE64
S 4 0 HU 72 020ALE64
NOTE: The Deskstar 7K4000 & 5K4000 hard drives
feature Advanced Format technology. Advanced Format
increases the physical sector size on hard drives from
512 bytes to 4096 (4K) bytes, which increases drive
capacities and improves error correction capabilities.
Please consult the HGST Advanced Format Drives page
on our website for more information on using these hard drives.
System Requirements for Serial ATA
The following are needed to install a Serial ATA
(SATA) drive to a system:
•
•
•
•• SATA capable motherboard or controller card
•
•
•
•• SATA hard drive
•
•
•
•• SATA cable (1 meter or less in length)
Handling precautions
Set the drive down gently to prevent damage
from impact or vibration.
Do not open the ESD bag containing the drive
until needed.
Handle the drive carefully by the edges. Do not
touch the exposed printed circuit board or any
electronic components.
Do not press on the top or bottom of the drive.
Before handling the drive, discharge any static
electricity from yourself and your clothing. With
one hand, touch an unpainted metal surface on
your computer chassis, then touch the ESD bag
with the other hand. Remain in contact with the
chassis and the bag for a minimum of two
seconds.
Quick installation procedure
Note: Back up all data before installing drive.
1. Turn off the computer.
2. Unplug the computer.
3. Remove the computer cover as instructed by
the computer system manual.
4. Discharge static electricity (see Handling
precautions).
5. Note the mounting position of existing drives
and cables. If you are replacing a drive or any
cable, remove it now.
6. Remove the drive from the ESD bag.
7. Record the model, the part number, and the
serial number of the drive for future reference.
8. Attach the Serial ATA cable to the drive. Match
key on cable to connector on drive
Mounting instructions
Note: The mounting hole and connector locations are
shown in figures 1 and 2.
1. Mount the drive securely.
2. Verify all attachments.
3. Replace the computer cover.
4. Plug in the computer.
5. Turn on the computer.
6. Verify that the hard disk is recognized by the
BIOS. Instructions for accessing your BIOS
can be found in the computer system manual
or in the motherboard manufacturer
documentation. If the drive is not recognized in
the BIOS, check the following:
HGST, a Western Digital company
Page 2 version 1.0
1) Auto Detect is enabled for the port the hard
disk is connected to.
2) SATA and power cables are connected
securely and not damaged.
3) The latest BIOS version is loaded onto the
system.
7. Many factors must be considered in order to
take advantage of the full capacity of drives
>2.2TB. Some configurations offer a higher
likelihood of success. Please refer to our
High Capacity Technology Brief and visit
our Above 2TB web page at
http://www.hitachigst.com/internal-
drives/above-2tb.
8. Your operating system setup utility will provide
instructions on how to partition and format your
drive before it installs the operating system.
For additional information see:
www.hitachigst.com/support
Note: The hard supportdrive s 6Gbps, 3Gbps and
1.5Gbps interface speeds. Higher interface speeds
are gated by Host Bus Adapter (HBA) or SATA
chipset of the system.
Mounting Recommendations
The drive will operate in all axes (6 directions).
Performance and error rate will stay within
specification limits if the drive is operated in the other
orientations from which it was formatted.
For reliable operation, the drive must be mounted in
the system securely enough to prevent excessive
motion or vibration of the drive during seek operation
or spindle rotation, using appropriate screws or
equivalent mounting hardware.
The recommended mounting screw torque is 0.6 - 1.0
Nm (6- 10 Kgf.cm).
The recommended mounting screw depth is 4 mm
maximum for bottom and 4.5 mm maximum for
horizontal mounting.
Drive level vibration test and shock test are to be
conducted with the drive mounted to the table using
the bottom four screws.
Thread (1) (2) (3) (4) (5) (6) (7)
6- 32UNC 41.28±0.5 44.45±0.2 95.25±0.2 6.35±0.2 28.5±0.5 60.0±0.2 41.6±0.2
Figure 1: Mounting holes locations (all dimensions are in mm)
Figure 2:
Connector location (all dimensions are in mm)
Interface connector

Produkt Specifikationer

Mærke: HGST
Kategori: Harddisk
Model: UltraStar 7K4000

Har du brug for hjælp?

Hvis du har brug for hjælp til HGST UltraStar 7K4000 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Harddisk HGST Manualer

HGST

HGST UltraStar 7K4000 Manual

1 September 2024
HGST

HGST Travelstar 7K500 Manual

1 September 2024
HGST

HGST Travelstar Z5K320 Manual

1 September 2024
HGST

HGST Travelstar Z7K500.B Manual

1 September 2024
HGST

HGST Travelstar 5K500.B Manual

1 September 2024
HGST

HGST Ultrastar A7K2000 Manual

1 September 2024
HGST

HGST 5K320 Manual

22 Maj 2024

Harddisk Manualer

Nyeste Harddisk Manualer

Sandisk

Sandisk PRO-BLADE TRANSPORT Manual

28 Juli 2025
Sandisk

Sandisk G-DRIVE ArmorATD Manual

27 Juli 2025
Sandisk

Sandisk G-RAID Shuttle Manual

27 Juli 2025
Sandisk

Sandisk PRO-BLADE SSD MAG Manual

27 Juli 2025
Sandisk

Sandisk PRO-G40 SSD Manual

27 Juli 2025
Sandisk

Sandisk G-RAID SHUTTLE 4 Manual

27 Juli 2025
Sandisk

Sandisk G-DRIVE PRO SSD Manual

27 Juli 2025
Sandisk

Sandisk G-DRIVE SSD Manual

27 Juli 2025
Icy Box

Icy Box IB-G226L-C31 Manual

23 Juli 2025
Highpoint

Highpoint RocketStor 6618V Manual

19 Juli 2025