Hobbywing XeRun 3660 SD G2 Manual

Hobbywing Radiostyret legetøj XeRun 3660 SD G2

Læs gratis den danske manual til Hobbywing XeRun 3660 SD G2 (1 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Hobbywing XeRun 3660 SD G2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

It’s important to select the FDR/gear ratio properly, as improper FDR/gear ratio may cause you great loss. Therefore, please choose the gear ratio by referring to the following points!

1. Operating Temperature of the Motor

The motor temperature should be lower than 100 during the operation. Temperatures above 100 will weaken the magnet and may partly melt the coils and eventually damage the ESC (due to strong ℃/212℉ ℃

current). Therefore, the most effective way to prevent overheat is to select the right gear ratio.

2. Principle of Gear Ratio Selection

To avoid potential risks such as ESC/motor damage or malfunction caused by overheat, please start with a very small pinion first and check the ESC & motor temperatures regularly throughout the run. This is the only

way to guarantee that your motor won’t overheat. If the motor and ESC temperatures remain stable and low in the running, then you can slowly increase the pinion size while monitoring temperatures to determine

the safe gearing for your vehicle, climate and track condition. Because these elements may change, so please keep monitoring the ESC & motor temperatures to protect your electronics from damage.

• (With the motor direction set to CCW), take the graduation/value after "CCW" on the motor case as the starting point when

adjusting the timing. (With the reversed triangle pointing at a value/graduation,) the smaller/bigger the value,

the smaller/bigger the timing. The timing is 40 degrees (as shown in picture 1) when the motor direction is set to CCW.

• (With the motor direction set to CW), take the graduation/value after "CW" on the motor case as the starting point when

adjusting the timing. (With the reversed triangle pointing at a value/graduation,) the smaller/bigger the value,

the smaller/bigger the timing. The timing is 20 degrees (as shown in picture 1) when the motor direction is set to CW.

• The motor timing is 30 degrees by default (as shown in picture 2). The motor timing should be within 30 to 40 degrees if you

want to activate the Turbo timing. And the timing can be within 20 to 40 degrees if you have no intention to activate the Turbo timing.

Warnings

CAUTIONS

Thank you for purchasing the XERUN 3652/3660 G2, HOBBYWING’s high performance

sensored brushless motor! Brushless power systems can be very dangerous, any improper

use may cause personal injury and damage to the product and related devices. We

strongly recommend reading through this user manual before use. Because we have no

control over the use, installation, or maintenance of this product, no liability may be

assumed for any damages or losses resulting from the use of this product. We do not

assume responsibility for any losses caused by unauthorized modifications to our product.

ATTENTION

FDR/Gear Ratio Selection

Timing Adjustment

Features

Assembly/Disassembly

For prolonging the motor life and raising its efficiency, we recommend checking and cleaning the motor regularly. About the frequency, it depends on the times you

use the motor and the track condition. Please refer to the following diagrams to assemble your motor and dismantle it in the reverse order if necessary.

Parts List:

USER MANUAL

XERUN 3652/3660 G2

Sensored Brushless Motor

Installation & Connection

1. How to Mount the Motor into a RC vehicle

M3 mounting screws (6*M3) are needed here, as the mounting holes are 5mm in depth, so we don’t recommend using the M3 screws

with the length exceeds 8mm to mount the motor into your vehicle.

2. How to Connect the Motor to an ESC

There are three power wires coming from the ESC must be soldered to the motor. They are usually color coded as Blue for Wire A, Yellow

for Wire B and Orange for Wire C. When connecting the power wires between the ESC and motor, please make sure that you match ESC

Wire A to Motor Phase A, ESC Wire B to Motor Phase B and ESC Wire C to Motor Phase C (this is very important).

• When using a Sensored ESC, make sure the sensor cable is clean and undamaged first and then connect the sensor cable to both the

ESC and the motor in the correct direction.

• When using a Sensorless ESC, swap any two wires if the motor runs in reverse.

3. Recheck the Installation & Connections

Recheck the installation and all the connections before turning on the power.

3100

3800

4300

5100

6100

3100

3800

4300

5100

6100

3200

3600

4300

0.0087Ω

0.0059Ω

0.0052Ω

0.0035Ω

0.0029Ω

0.0087Ω

0.0059Ω

0.0052Ω

0.0035Ω

0.0029Ω

0.0065Ω

0.0056Ω

0.0038Ω

2.9A

3.9A

4.2A

4.7A

5.9A

2.9A

3.9A

4.2A

4.7A

5.9A

3.7A

4.1A

4.7A

192g (6.77oz)

187g (6.60oz)

192g (6.77oz)

186g (6.56oz)

192g (6.77oz)

187g (6.60oz)

192g (6.77oz)

186g (6.56oz)

218g (7.69oz)

214g (7.55oz)

218g (7.69oz)

1/10

Light-duty SCT

Truck

Monster Truck

1/10

Heavy-duty SCT

Truck

Monster Truck

30401050

30401052

30401053

30401054

30401055

30401056

30401058

30401059

30401060

30401061

30401150

30401151

30401152

2-3S

Φ=3.175mm(0.125in)

L=15mm(0.591)

Φ=5mm(0.197in)

L=17mm(0.669in)

Φ=5mm(0.197in)

L=15mm(0.591in)

XERUN-3652SD-3100KV-D3.175-G2

XERUN-3652SD-3800KV-D3.175-G2

XERUN-3652SD-4300KV-D3.175-G2

XERUN-3652SD-5100KV-D3.175-G2

XERUN-3652SD-6100KV-D3.175-G2

XERUN-3652SD-3100KV-D5.0-G2

XERUN-3652SD-3800KV-D5.0-G2

XERUN-3652SD-4300KV-D5.0-G2

XERUN-3652SD-5100KV-D5.0-G2

XERUN-3652SD-6100KV-D5.0-G2

XERUN-3660SD-3200KV-D5.0-G2

XERUN-3660SD-3600KV-D5.0-G2

XERUN-3660SD-4300KV-D5.0-G2

Φ=36mm (1.417in)

L=52.5mm (2.067in)

Φ=36(1.417in)

L=62(2.44in)

Specifications

ModelPN

(No-load)

No-load

Current

Motor Diameter

& Length

Shaft Diameter

& Length

Poles Weight ApplicationsLiPo

Resistance

• Innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented) with low cogging effect and torque pulsation greatly improves control feel around corners.

• Built-in chip for making the motor be easily identified by HOBBYWING ESCs. When pairing it with a HW 1/8th sensored ESC (i.e. XR8 SCT/Plus), the motor can work in the “sensored” mode at all times with great

output linearity after the identification. The Turbo timing is allowed to be activated for higher output.

• Magnetic ring mounted on the rotor protects the motor from signal interference and guarantees its super stability in the “sensored” mode.

• With the mechanical timing adjustable from 20 degrees to 40 degrees, users are able to have different output power.

• Turbine design implemented by the rotor accelerates the internal air circulation and reduces heat.

• Rebuild-able design (partially rebuild-able) and screw-less motor case for easy routine maintenance effectively prolong the motor life and raise the motor effficiency.

• CNC machined aluminum housing, high purity copper windings, advanced rotor structure, high-quality alloy steel output shaft, high-precision bearings for high durability and smoothness.

• New-style “U” solder tabs at the bottom of the motor for easy soldering and wiring.

17mm 62mm

4.5mm

Ø5mm

15mm

20.6mm

Ø35.9mm

6-M3

Ø25.4mm

60°

C.C.W

XERUN 3660SD G2XERUN 3652SD G2XERUN 3652/3660SD G2 XERUN 3652/3660SD G2

52.5mm 15mm

4.5 / 2.8mm

Ø Ø3.1755 / mm

Picture 1 Picture 2

Back End Bell x 1PCS

Stator Set x 1PCS

Screws for Fastening

the Back End Bell

2PCS (M2.5*8.0mm)

Rotor x 1PCS

1 2 3 4 5

Mount washers

( the wave washer first,

then the flat washer ) Mount the motor rotor Mount the back end bell set

Mount screws for

fastening the back end bell

Picture of the

assembled motor

XERUN 3660SD G2

Brushless Electronic Speed Controller

Sensor wire

Motor B

Motor A

Motor C

• Never leave this product unsupervised when it is powered on.

• Ensure all wires and connections are well insulated before connecting the motor to related devices,

as short circuit will damage your motor.

• Please strictly follow the A-A, B-B and C-C wiring order when connecting an ESC to the motor.

• Never allow this product to come in contact with water, oil, fuel or other electro-conductive liquids.

If this happens, stop the use of your product immediately and let it dry carefully.

• Read through the manuals of all power devices and chassis and ensure the power configuration is

rational before using this unit.

• Never hit full throttle before installing the pinion, as high speed rotation may cause damage to the

motor in circumstances of no load.

• Ensure all devices are well connected, in order to prevent poor connection that may cause your

vehicle to lose control or other unpredictable issues such as damage to the device.

• Stop using the motor when its shell temperature exceeds 100℃/212℉; otherwise the rotor may be

demagnetized and cause irreversible damage to your motor.

Flat Washer x 1Pcs

Wave Washer x 1Pcs

20161215

Produkt Specifikationer

Mærke:	Hobbywing
Kategori:	Radiostyret legetøj
Model:	XeRun 3660 SD G2
Type:	Radio-Controlled (RC) Model Parts
Vægt:	218 g
Produktfarve:	Sort
Motortype:	Børsteløs motor
Produkttype:	Motor
Batteriteknologi:	Lithium polymer (LiPo)
Husmateriale:	Aluminium
Normal brug:	Bil
Mærke kompatibilitet:	Hobbywing
Antal poler:	4
Diameter aksel:	5 mm
Aksellængde:	17 mm
Motor - diameter:	36 mm
Ingen aktiv strøm:	4.7 A
Motor hastighedskonstant (KV):	4300 RPM/V
Motor længde:	62 mm
Motor modstand:	0.0038 ohm (Ω)