Honeywell F300B2012 Manual


Læs gratis den danske manual til Honeywell F300B2012 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Honeywell F300B2012, eller vil du spørge andre brugere om produktet?

Side 1/6
OWNER’S GUIDE
69-0756-07
F50F and F300E Electronic
Air Cleaners
CONTENTS
Operating Your Electronic Air Cleaner ....................... 2
Getting the Most From Your Electronic Air Cleaner 2
Cleaning Prefilter(s), Cell(s) and Postfilter(s) ......... 3
How Electronic Air Cleaning Works ............................. 5
Before You Call for Service .............................................. 6
Resideo 10 Year Ultraclean Coil Guarantee™ .......... 6
Limited Five-year Warranty ............................................ 7
Product Registration ......................................................... 8
M38810
F50F AND F300E ELECTRONIC AIR CLEANERS
69-0756—07 2
OPERATING YOUR
ELECTRONIC AIR CLEANER
GETTING THE MOST FROM
YOUR ELECTRONIC AIR
CLEANER
Run the electronic air cleaner as much as
possible
For greatest efficiency, the air cleaner should run all the
time. To do this, set the Fan switch on your thermostat to
On, and make sure the air cleaner is turned on. The fan
and air cleaner run even when the furnace or air
conditioner is off.
NOTE: A manual fan switch may be built into the furnace
or furnace fan controller.
The air cleaner uses less power than a 40 watt light bulb
(two-cell model—33 watts; single cell model—22 watts).
Many believe that the added cost is more than offset by
the added benefits of full-time air cleaning and full-time
air circulation. And you may feel that the room
temperature stays more even when the fan is always on.
Even if your thermostat does not have a Fan On position,
you can obtain maximum available air cleaning benefit by
making sure the air cleaner is always turn to On so it
operates whenever the furnace or air conditioner is on.
Keep the cell(s) and prefilter(s) clean
Although the air cleaner is designed to be efficient over a
wide range of cell dirt loading conditions, regular cleaning
is your best assurance of consistent performance. Also, a
very dirty prefilter and cell reduces air flow and, in turn,
this reduces the efficiency of the furnace or air
conditioner.
Replace postfilter regularly
A high-efficiency postfilter is sometimes installed in the
air cleaner. This filter increases the efficiency of the air
cleaner and should be changed every six months of usage.
If you have a humidifier
All Resideo whole house humidifiers can be used in a
system with the Resideo Electronic Air Cleaner without
any additional filters or system modification.
If your system includes an atomizing humidifier, you may
want to install a standard furnace filter between the
humidifier and the air cleaner.This filter would keep the
humidifier spray mineral deposits from collecting on the
air cleaner.This filter should be checked regularly and
changed when it shows signs of mineral or dirt buildup. If
you do not install a filter, you will probably need to wash
the cell(s) and prefilter(s) more often to remove the
mineral buildup.
If an ultrasonic room humidifier is used often, especially if
filled with tap (undistilled) water, the cell(s) and prefilter(s)
require more frequent washing. A white residue
accumulates on the cell(s) from the minerals in the water.
This residue may also contribute to "white dust.” See About
lint or “white dust” section for more information.
Turn the On-Off switch on the power
box to On.
NOTE: Set the switch to 1 for On
and set the switch to O for
Off.
The air cleaner now operates
whenever your furnace/air
conditioning system fan operates.
For maximum air cleaning benefit
and cleaner air conditioner coils,
leave the air cleaner switch turned
on at all times and the thermostat
fan switch set to On. Of course,
continuous fan operation adds to
your electric bill each month. Check
your equipment for the amount of
electricity needed to run your
System fan.
When the fan and air cleaner come
on, the neon indicator lights.
You may hear a snapping (electrical
arcing) sound occasionally as the air
cleaner operates. This is usually
caused by a larger dust particle that
causes a high voltage discharge.The
snapping sound means that your air
cleaner is working as it should.To
hear the snapping sound,
momentarily press the test button
near the botton of the door. Use the
test button any time you want to
prove air cleaner operation.
The switch remains in the On
position to keep the air cleaner
running.
When the fan and air cleaner stops,
the neon light goes off. The air
cleaner is off until the heating or air
conditioning and fan start again.
If you do not want the air cleaner to
run, set the On-Off switch to Off to
turn off the air cleaner. Your furnace
and air conditioner continue to
operate normally, but without the
added benefit of air cleaning.
Normally, this switch should be turn
to On at all times.
M3584A
M3586A
M6032A
M3585A
M3583A


Produkt Specifikationer

Mærke: Honeywell
Kategori: Ikke kategoriseret
Model: F300B2012

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell F300B2012 stil et spørgsmål nedenfor, og andre brugere vil svare dig