Hudson Valley Prospect Park 1423-AGB Manual

Hudson Valley Ikke kategoriseret Prospect Park 1423-AGB

Læs gratis den danske manual til Hudson Valley Prospect Park 1423-AGB (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Hudson Valley Prospect Park 1423-AGB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FIXTURE INSTALLATION

1. Determine the location for the lamp. Using the mounting plate as a template, mark the location of the holes for

the wall ANCHORS(5).

2. Drill the appropriate size holes for the WALL ANCHORS(5). (the holes should be slightly smaller than the size of

the anchors.) Install the wall ANCHORS(5) to the hole.

3. Attach the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is

designed to be mounted on standard junction box. The junction box must be securely mounted to the structure

of the building. Screw in the WOOD SCREW (6) to the ANCHORS(5).

4. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

5. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together

with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with

electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires

same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS

COULD RESULT IN SERIOUS INJURY OR DEATH!

5. Attach the FIXTURE ASSEMBLY (8) to the MOUNTING PLATE (1) and secure with the SET SCREWS (7)

6. Screw the BULB (11) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 75 WATT LAMP. DO

NOT EXCEED THE RECOMMENDED WATTAGE!

7. Secure the GLASS SHADE (9) onto the FIXTURE ASSEMBLY (8) by using two BOLT NUT (10).

8. Restore power to the outlet at the breaker or fuse box.

PROSPECT PARK

1423

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS

AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR

TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

910

ITEM DESCRIPTION PART NUMBER

MOUNTING PLATE

MPT-001423

MOUNTING SCREW HDW-001423

GROUND SCREW HDW-001423

WIRE NUT HDW-001423

ANCHOR HDW-001423

WOOD SCREW HDW-001423

M4 SET SCREWS HDW-001423

FIXTURE ASSEMBLY FAS-001423

GLASS GLS-001423

BOLT NUT NUT-001414-B

BLB-75-T10-8.5 NOT INCLUDED