Hunter 44132 Manual

Hunter Termostat 44132

Læs gratis den danske manual til Hunter 44132 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Hunter 44132, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

This thermostat is compatible with most conventional oil, gas,

electric, hot water systems, single stage, and multi-stage heat

pumps. This thermostat will not control line voltage systems.

You will need the following tools to complete your installation:

• Phillips Screwdriver (#2)

• Two 1.5V (AA) size alkaline batteries

Take note of these warnings and cautions before

proceeding:

• Read all installation instructions before beginning installation!

If you still need assistance after reading this manual, call our

Technical Support at 1-888-830-1326.

• Do not disconnect the wires from your old

thermostat until all wires have been properly

labeled. You must label all wires properly because

wire color may not indicate the function of the wire.

• All wiring must be done in accordance with local code and

ordinances.

• Always turn power off to your furnace/compressor before the

installation process. Failure to do so could result in damage to

your thermostat and/or your heating and cooling system. Do not

restore power until your installation is complete.

• This thermostat is designed for use with 24V AC/millivolt systems

with a maximum of 1 amp. Higher amp or line voltage systems

will cause damage to your system and increase the risk of fire.

44127, 44132 Programmable ermostat

Preparation

Gathering Tools and Warnings 1

Old ermostat Removal

1. Turn off power to your compressor and furnace.

2. Remove the cover to your existing thermostat. Some thermostats

may have screws or other locking devices that must rst be

removed. Once the wallplate is exposed, locate the wire

terminals and try to identify the wire designations. If the wire

terminals are not visible, they may be connected to the back of

the wallplate. Look for any additional screws, tabs, or locking

devices to remove the wallplate. See Figure 1. If you are still

unable to nd the terminals for the wires, it may be necessary

to contact the manufacturer of the original thermostat.

Installation 2

Mounting the Wallplate

Wire Color Wire letter

Figure 2.

Figure 3b.

R, V

Y, Y1, M

G, F

L, F, X

O, R

W2, E, X,

Aux

C, X, X1, B

Heat Pump

Figure 6.

1. Remove the mounting plate by pulling it straight off the back of

the Thermostat. Figure 5.

Figure 5.

2. Pull the wires through the back of the mounting plate, ensuring

none of the wire labels are removed. Figure 6.

Figure 7.

bubble level

Figure 8.

3. Using a Phillips Screwdriver, Partially install 1 screw into the

top hole of the thermostat. Ensure the thermostat is level using

the bubble level on the mounting plate Figure 7., then install

the other screw. Tighten both screws until secure. Figure 8.

Figure 11.

4. Check the charts on the back of this sheet and identify your

system type. They are divided by Conventional and Heat Pump

installations.

5. Raise all of the levers on the terminals you will be using. Heat

Pump Installation labels are located on the left of the terminal

blocks on the mounting plate and Conventional labels are

on the right. If your installation does not call for the jumper,

remove it now. It is located underneath the wire holes, between

the RH and RC terminals on the conventional side. Figure 9.

6. If one of the terminals you need has a tab in front of it, use

your nger to break the tab away. Figure 9.

Note: Only break tabs you know you will be using. Double

check your wiring conguration and make sure you are familiar

with the terminals you will be using.

7. Insert the bare end of each wire all the way into the appropriate

hole in the terminal block that matches the wire label then

lower the lever. This will lock each of the wires in place. Tuck

excess wire back into wall after they have been locked in the

mounting plate.

Note: Do not insert the wires into the holes in the top of the

mounting block. The wires should be inserted into the front close

to the hole in the mounting plate. See Figure 8.

8. Before mounting the thermostat onto the mounting plate, turn it

over and nd the 2 switches located on the circuit board next

to the battery compartment.

9. Set the system switch to “Conv” if you have a conventional

HVAC system or “HP” if you have a heat pump system. Set the

furnace type to “Elc” if you have an electric convention system

or a heat pump. “Gas/Oil” will be used if you have gas or oil

based conventional system. Figure 10.

Note: Conventional systems use the compressor for air

conditioning and a separate furnace for heat. Heat pump systems

use the compressor for both heating and cooling.

10. Lay the ribbon across the battery compartment and install 2

(AA) Batteries into the back of the thermostat over it, Figure

10., and snap the thermostat on to the mounting plate. Refer to

“Setup” on page 10 of your owner’s manual to continue setup,

scheduling, and daily use.

If you have any additional questions or problems with your Hunter

thermostat, please call:

USA: 1-888-830-1326

Canada: 1-866-268-1936

Hours of operation are from 7:00 am to 7:00 pm Monday - Friday

and 8:00 am to 5:00 pm on Saturday, Central Time. You may also

Technical Support

Installation Sheet

Conventional

RC, R

Y, Y1

G, F

W, W1

Figure 3a.

Figure 1.

ermostat Cover

Wallplate

ermostat Cover

Wallplate

W G Y RC RH

Tabs

Levers

Figure 9.

Jumper

Insert

Wires

Conv HPElec Gas

Figure 10.

Gas

Oil

Elc

H.P.

Cnv.

Labeling Your Wires

Use the table in Figure 2. to write down your wire colors and

the letter designations on the old thermostat. This will allow you

to keep a record of your old thermostat’s wiring conguration

should you need to refer to it at a later time. This will also help our

Technical Support Department determine your system type and

proper wiring, should you need to contact them. Wire color does

not indicate the function of the wire, this is being used only to help

determine which wire has what letter designation.

After writing down the wire colors

and letters, use the terminal stickers

to label the wires. Figures 3a and 3b

will help you depending on system

type; Conventional or Heat Pump.

Not all terminals will be used, this will

be determined by your system type.

To ensure wires do not fall back into

the wall hole, you may tape them

to the wall, or wrap them around a

pencil.

Figure 4. may assist you if your old

thermostat is a heat pump from one

of the listed Manufacturers and your

wire labels do not match. It is located

on the back of this sheet. These tips

will also help you in wiring:

• Only 1 reversing valve is needed

to run a heat pump. If both “O”

and “B” are present, “B” may be a

common wire.

• Often, 2-wire heat only systems do

not have terminal labels. Connect 1

wire to the Rh terminal and the other

to W.

• If you have a 3-wire hot water

system, the damper valve control

wire will be labeled and attached to

the “A” terminal.

• If you need further assistance

with wiring, or determining your

system type, you can contact our

Technical Support Department. See

the “Technical Support” section for

information.

Produkt Specifikationer

Mærke:	Hunter
Kategori:	Termostat
Model:	44132

Har du brug for hjælp?

Hvis du har brug for hjælp til Hunter 44132 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Hunter Manualer

11 Januar 2025

21 August 2024

17 August 2024

15 August 2024

14 August 2024

13 August 2024

12 August 2024

12 August 2024

11 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Vimar 30811.C Manual

31 Oktober 2025

Abus Comfion FUSH80100 Manual

29 Oktober 2025

Delta Dore Tybox 137 Manual

17 Oktober 2025

Delta Dore RF 6600 FP Manual

17 Oktober 2025

Emos P56A01 Manual

15 Oktober 2025

Fantini Cosmi C830RL Manual

14 Oktober 2025

UPM HTM311A Manual

12 Oktober 2025

Bticino NT4451 Manual

8 Oktober 2025

Bticino HS4451 Manual

7 Oktober 2025

Bticino N4451 Manual

7 Oktober 2025