Icom IC-F5062D Manual

Icom Ikke kategoriseret IC-F5062D

Læs gratis den danske manual til Icom IC-F5062D (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Icom IC-F5062D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTRUCTIONS

VHF dPMR MOBILE TRANSCEIVER

|F5062D

UHF dPMR MOBILE TRANSCEIVER

|F6062D

1-1-32 Kamiminami, Hirano-ku,

Osaka 547-0003, Japan

Feb. 2023

A7217W-1EU-4

Printed in Japan

Icom and the Icom logo are registered trademarks of

Icom Incorporated (Japan) in Japan, the United States,

the United Kingdom, Germany, France, Spain, Russia,

Australia, New Zealand, and/or other countries.

AMBE+2 is a trademark and property of Digital Voice

Systems Inc.

All other products or brands are registered trademarks or

trademarks of their respective holders.

IMPORTANT

This instruction sheet includes some functions that are

usable only when they are preset by your dealer. The

transceiver may have other functions and operations that

are not described in this instruction sheet. Ask your dealer

for preset function details.

EXPLICIT DEFINITIONS

WORD DEFINITION

RWARNING!



shock may occur.

CAUTION Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No



shock.

ANTENNA

A key element in the performance of any communication

systems is the antenna. Contact your dealer for

information regarding antennas and how to install them.

FUSE REPLACEMENT

Fuses are installed in the supplied DC power cable. If a

fuse blows, track down the source of the problem, repair it,

and then replace the damaged fuse with a new rated one.

LFuse rating: 250 V 10 A

NOTE:

Fuse rating explanation

Fuse coding: FUSE 250 V 10 A

Fuse voltage rating: 250 Volts

Fuse current rating: 10 Amperes

ABOUT CE AND DOC

Hereby, Icom Inc. declares that the versions

of IC-F5062D and IC-F6062D which have

the “CE” symbol on the product, comply with

the essential requirements of the Radio

Equipment Directive, 2014/53/EU, and the



substances in electrical and electronic

equipment Directive, 2011/65/EU. The full

text of the EU declaration of conformity is

available at the following internet address:

https://www.icomjapan.com/support/

About e-marking: Detailed installation notes for



available.

Please contact your Icom dealer or distributor.

DISPOSAL

The crossed-out wheeled-bin symbol on your

product, literature, or packaging reminds you

that in the European Union, all electrical and

electronic products, batteries, and

accumulators (rechargeable batteries) must

be taken to designated collection locations at

the end of their working life. Do not dispose

of these products as unsorted municipal

waste. Dispose of them according to the

laws in your area.

VOICE CODING TECHNOLOGY

The AMBE+2™ voice coding Technology embodied in this

product is protected by intellectual property rights including

patent rights, copyrights and trade secrets of Digital Voice

Systems, Inc. This voice coding Technology is licensed

solely for use within this Communications Equipment.

The user of this Technology is explicitly prohibited from

attempting to extract, remove, decompile, reverse

engineer, or disassemble the Object Code, or in any other

way convert the Object Code into a human-readable form.

U.S. Patent Nos.

#8,595,002, #8,359,197, #8,315,860, #8,200,497,

#7,970,606, #6,912,495 B2.

PRECAUTIONS

RWARNING! NEVER connect the transceiver to an AC



shock.

RWARNING! NEVER operate the transceiver during a

lightning storm. It may result in an electric shock, cause



power source and antenna before a storm.

RWARNING! NEVER connect the transceiver to a power

source of more than 16 V DC such as a 24 V battery. This

could damage the transceiver.

RWARNING! NEVER cut the DC power cable between

the DC plug and fuse holder. If an incorrect connection is

made after cutting, the transceiver might be damaged.

RWARNING! NEVER place the transceiver where normal

operation of the vehicle may be hindered or where it could

cause bodily injury.

CAUTION: DO NOT expose the transceiver to rain, snow

or any liquids.

CAUTION: DO NOT

󰀨

and may damage the radio.

CAUTION: DO NOT place or leave the transceiver in

areas with temperatures below –25°C or above +55°C, or

in areas subject to direct sunlight, such as the dashboard.

CAUTION: DO NOT operate the transceiver without

running the vehicle’s engine. The vehicle’s battery will

quickly run out when the transceiver transmits while the

vehicle’s engine is OFF.

CAUTION: DO NOT place or leave the transceiver in

excessively dusty environments.

CAUTION: DO NOT place the transceiver against walls.

Otherwise heat dissipation will be obstructed.

CAUTION: DO NOT use harsh solvents such as



transceiver’s surfaces.

CAUTION: CONFIRM that all connectors and jacks are

dry and clean before attachment. Exposing them to dust or

water will result in serious damage to the transceiver.

NEVER place the transceiver in an insecure place to avoid



BE CAREFUL! The transceiver will become hot when

operating continuously for long periods.

CLEANING

If the transceiver becomes dusty or dirty, wipe it clean with

a soft, dry cloth.

SUPPLIED ACCESSORIES

OPTIONS

•RMK-3  + OPC-609 

Allows you to install the transceiver’s main unit separately

from the front panel for operating convenience.

•SP-30/SP-35/SP-35L 

Input impedance: 4 ø

SP-35/SP-35L: Rated input 5 W, Max. input 7 W

SP-30: Rated input 20 W, Max. input 30 W

•HM-152/HM-152T/HM-148G/HM-148T 

HM-152: Hand microphone

HM-152T: DTMF microphone

HM-148G: Self grounding heavy duty microphone

HM-148T: Self grounding heavy duty microphone with

10-keypad

The 10-keypad of this microphone can be

used for the DTMF code transmission only.

•SM-26 

•UT-109R/UT-110R 

Non-rolling type (UT-109R)/Rolling type (UT-110R) voice

scrambler unit provides high communication security.

Icom is not responsible for the destruction, damage to, or

performance of any Icom or non-Icom equipment, if the

malfunction is because of:

•



disasters, disturbances, riots, war, or radioactive

contamination.

•The use of Icom transceivers with any equipment that is

not manufactured or approved by Icom.

See the operating guide for details of the IDAS™ dPMR™

(digital Private Mobile Radio) and the BIIS (Binary

Interchange of Information and Signaling) 1200 system

operations. Ask your dealer for details.

Thank you for choosing this Icom product.

READ ALL INSTRUCTIONS carefully and completely

before using this product.

SAVE THESE INSTRUCTIONS — These instructions

contain important operating instructions for the

IC-F5062D and the IC-F6062D.

Sponges*

Used for labeling the programmable function keys

according to their assigned functions.

Used for optional unit installation.

Ask your dealer for details.

NOTE: Some accessories are not supplied, or the shape

󰀨

MOUNTING THE TRANSCEIVER

The universal mounting bracket supplied with your

transceiver allows under or overhead mounting.

•Mount the transceiver securely with the 4 supplied

screws to a thick surface that can support more than 1.5

kg (3.3 lb).

Flat washer

Felt*

Spring washer

When using the

self-tapping screws

*The felt pads reduce vibration.

For European versions

CAUTION: DO NOT Hot surfaces. touch

the transceiver’s surface after continuously

transmitting for long periods of time. The

transceiver’s chassis radiates heat, and it

will become hot to protect the power



may cause a burn.

Microphone

Microphone hanger

and screw set

Function name

stickers*

Microphone

hanger cable

Mounting bracketDC power cable

Bracket bolts Mounting screws

(M5×12 mm)

Self-tapping screws

(M5×16 mm)

Flat washers Spring washers Nuts

Bracket

bolt

FREQUENCY RANGE AND OUTPUT POWER

IC-F5062D VHF dPMR Mobile Transceiver

Frequency Range Output Power

 25 W

•



* For only the Digital mode

IC-F6062D UHF dPMR Mobile Transceiver

Frequency Range Output Power

 25 W

•



* For only the Digital mode

PANEL DESCRIPTION FUNCTION DISPLAY

REAR PANEL CONNECTION

ANTENNA CONNECTOR

Connect to an antenna. Contact your dealer about

antenna selection and placement.

2 EXTERNAL SPEAKER JACK

Connect a 4 ~ 8 Ω external speaker.

3 D-Sub 25-pin

Connects to an external unit.

MICROPHONE HANGER

Connect the supplied microphone hanger to the

vehicle’s ground for microphone ON/OFF hook

functions. (See ‘PANEL DESCRIPTION’ for details.)

5 IGNITION LEAD

Connects to an ignition line.

CAUTION: DO NOT

put a pressure on this lead.

Binding to the DC power cable is recommended.

DC POWER RECEPTACLE.

Connects to a 12 V DC battery. Pay attention to

polarities.

RWARNING! NEVER connect to a 24 V battery. This

will damage the transceiver.

DAbout the LED indicator

zLights red while transmitting.

zLights green while receiving a signal, or when the

squelch is open.

DAbout the Microphone connector

Connect the supplied or optional microphone.

NEVER connect non-specied microphones. The pin

assignments may be di󰀨erent and may damage the

transceiver.

[VOL]

LED indicator Up/Down keys

Power key [ ]

Dealer-assignable keys*

[P0], [P1], [P2], [P3], [P4]

*Ask your dealer for details.

Function display Speaker

Microphone

connector

DMICROPHONE

The supplied or optional microphone has a PTT switch

and a hanger.

•The following functions are available when you put

the microphone ON the hook, or take it OFF the hook

(depending on the presetting):

- The automatic scan starts when you put it ON the hook.

- A scan is paused or canceled when you take it OFF

the hook.

- Automatically selects the Priority A channel when you

take it OFF the hook.

- Sets to the ‘Inaudible’ (mute) mode when you put it ON

the hook.

Sets to the ‘Audible’ (unmute) mode when you take it

OFF the hook

DTurning power ON

zHold down [ ] to turn ON the power.

NOTE: If the transceiver is programmed for a start up

password, input the digit codes as directed by your

dealer. See the operating guide for details.

DReceiving and Transmitting

Receiving:

1. Select a channel.

z Push [CH Up] or [CH Down].

z Push one of the direct channel select keys,

[MR-CH 1] to [MR-CH 4].

2. When receiving a call, rotate [VOL] to adjust the audio

output level to a comfortable listening level.

Transmitting:

Wait until the channel is clear to avoid interference.

1. Take the microphone OFF the hook.

•While scanning, the scan stops.

2. Wait for the channel to become clear.

•The channel is busy when the LED indicator lights green.

3. While holding down [PTT], speak at a normal voice

level.

4. Release [PTT] to receive.

IMPORTANT:

To maximize the readability of your signal:

1. After pushing [PTT], pause briefly before you start

speaking.

2. Hold the microphone 5 to 10 cm (2 to 4 inches) from

your mouth, then speak at a normal voice level.

BASIC OPERATION

DFor mobile operation DFor base station operation

Antenna

To an

AC outlet

DC Power

supply 13.2 V

Red

Black

Optional Speaker

Microphone

12 V

Battery

NOTE: Use the terminals as shown

below for the cable connections.

Crimp Solder

RWARNING! NEVER

remove the fuse holders

from the DC power cable.

RWARNING! NEVER

remove the fuse holders

from the DC power cable.

ANTENNA CONNECTOR

2 EXTERNAL SPEAKER JACK

3 D-Sub 25-pin

MICROPHONE HANGER

5 IGNITION LEAD

DC POWER RECEPTACLE.

Connects to a 13.2 V DC power supply. Pay attention

to polarities. Make sure the ground terminal of the DC

power supply is grounded.

NOTE: The antenna connector

type may di󰀨er, depending on

the transceiver versions.

NOTE: The antenna

connector type may

di󰀨er, depending on the

transceiver versions.

SIGNAL STRENGTH ICON

Displays relative received signal strength level.

Weak ← Receive Signal level → Strong

LOW POWER ICON

Displayed when the low output power is selected.

AUDIBLE ICON

z Displayed when the channel is in the ‘Audible’

(unmute) mode.

z Displayed when a matching signal is received.

COMPANDER ICON

Displayed when the Compander function is activated.

When the GPS indicator setting is ON*

Displayed when the GPS receiver acquires the GPS

signal from a satellite. In this case, the compander

icon does not show the Compander function’s status.

*Ask your dealer for details.

5 SCRAMBLER ICON

Displayed when the Voice Scrambler function is

activated.

BELL ICON

Displayed or blinks when a matching signal is

received, according to the presetting.

CALL CODE MEMORY ICON

Displayed when the call code memory is selected.

SCROLL ICON

Displayed when an SDM (Short Data Message),

including more than 12 characters, is selected in the

received message log screen by using [BIIS Button] or

[dPMR Button].

†, ‡

MESSAGE ICON

Displayed when an SDM or Status message is

received.

†, ‡



ALPHANUMERIC DISPLAY

z Displays an operating channel number, channel

name, User Set mode contents, DTMF code, etc.

z Depending on the presetting, characters are

displayed in 1 line or 2 lines on the LCD.

•In the instruction manual, the LCD illustration is

described as having characters displayed in 2 lines.



ACTIVATED KEY ICON

Displayed above the key assigned as [Scan], [Scan

Add/Del(Tag)], [Lock], [Talk Around], [Surveillance] and

[BIIS Button]

†

, while that key is activated.

†

BIIS operation only

‡

dPMR operation only

1

2

6

5

4

3

1

2

6

5

4

3

1 2 6543 7 8 9





LThe LCD display may di󰀨er, depending on the transceiver version.

Produkt Specifikationer

Mærke:	Icom
Kategori:	Ikke kategoriseret
Model:	IC-F5062D

Har du brug for hjælp?

Hvis du har brug for hjælp til Icom IC-F5062D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Icom Manualer

Icom IC-F29SR2 Manual

20 Juni 2025

Icom IC-FR5100 Manual

20 Juni 2025

Icom IC-DV75 Manual

20 Juni 2025

Icom IP1100CV Manual

20 Juni 2025

Icom IC-FR6100 Manual

20 Juni 2025

Icom IP110H Manual

20 Juni 2025

Icom OPC-2389 Manual

20 Juni 2025

Icom IC-F5400D Manual

20 Juni 2025

Icom IC-F5122D Manual

20 Juni 2025

Icom IC-2730 Manual

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive IAN 304227 Manual

20 Juni 2025

Ciarra CBCS5931B Manual

20 Juni 2025

IFM PL1507 Manual

20 Juni 2025

Rane AC 23B Manual

20 Juni 2025

LC-Power Integrator Pro LC6650B-SI V3.1 Manual

20 Juni 2025

Ciarra CBCS6903D Manual

20 Juni 2025

Curtis enGage II Manual

20 Juni 2025

Parkside HG10350 Manual

20 Juni 2025

Phoenix Gold ZDT-OPEL2 Manual

20 Juni 2025

Dahua Technology IVS-IP8000-E-GU1 Manual

20 Juni 2025