Icom OPC-2389 Manual

Icom Ikke kategoriseret OPC-2389

Læs gratis den danske manual til Icom OPC-2389 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Icom OPC-2389, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CONNECTION CABLE

INSTRUCTIONS

Thank you for choosing this Icom product.

The OPC-2389 connection cable is used to connect a

serial communication device to the VE-PG3 or VE-PG4.

READ ALL INSTRUCTIONS carefully and completely

before using this product.

Turn OFF the all devices that are connected to the VE-PG3 or VE-PG4, and then connect the OPC-2389, as shown below.

CONNECTING THE OPC-2389

CAUTION

• Verify that both the serial communication and the VE-PG3 or VE-PG4 are turned OFF when connecting or disconnecting

the cable.

• Hold the connector body when connecting or disconnecting them.

• Never bend or pinch the cable.

• Never place a heavy object on the cable.

• Never touch the cable with wet hands.

•

Always connect the cable correctly. An incorrect connection could damage the VE-PG3 or VE-PG4 and/or the connected device.

• Never add a pulling tension to the cable.

• Never use the OPC-2389 with any device other than VE-PG3 and VE-PG4.

Some serial communication devices may not be used.

VE-PG4 (Rear view)

OPC-2389

•

This is an example of connecting a serial communication device to the [EXT1] port.

A1 A4~B1 B4~C1 C4~

A1 A4~

B C

Be sure to insert the

connectors top side up.

Bottom

To a serial communication device

Top

1 2 3 4

qtrew

yo i u

B C

When other cables are connected, you can

use needle-nose pliers to carefully insert or

remove connectors.

VE-PG4 (Rear view)VE-PG4 (Rear view)

Needle-nose pliersNeedle-nose pliers

NEVER pull the connector by holding the

cable. This will damage the cable.

*If the cable becomes damaged, replace the

connector(s). See “REPLACING THE

CONNECTOR” to the right for replacement

details.

Connector

body

Connector

body

REPLACING THE CONNECTOR

If the cable becomes damaged, replace the connector(s). Make wire connections as described below.

• Spare connectors*

are supplied with the VE-PG3 or VE-PG4.

• If reconnecting is repeated about 30 times, replace the connector.

Manufacturer: DDK. Name: 232D-04S1B-DA5-FA

DO NOT lock the connector parts before inserting all wires.

Press the clear insert down

until it locks in place.

• After the insert is locked, it is

impossible to release it again.

Insert the wires into the holes

according to the assigned pin

numbers.

Connector

(Supplied with

the VE-PG3

or VE-PG4)

Connector

(Supplied with

the VE-PG3

or VE-PG4)

The wires for each hole

are assigned by color. See

the illustration below.

OPC-2389

B C

Pin No.

OrangeOrange

BlueBlue

YellowYellow

GrayGray

Connector top (Expanded view)

Br nBr nowow

GreenGreen

PurplePurple

RedRed

1 2 3 4 1 2 3 4

OPC-2389 connection and wires assignment

Icom and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United

Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.

A7471X-1J-2

Printed in Japan

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Jan. 2023

OPC-2389

Cut the wires*

near the connector.

Remove the cable

from the VE-PG3

or VE-PG4, before

cutting the wires.

DO NOT cut the wires too short.

Otherwise it will be difficult to

reconnect them to the VE-PG3 or VE-

PG4.

1 2 3 4

DISPOSAL

The crossed-out wheeled-bin symbol on your

product, literature, or packaging reminds you

that in the European Union, all electrical and

electronic products, batteries, and

accumulators (rechargeable batteries) must

be taken to designated collection locations at

the end of their working life. Do not dispose of these products

as unsorted municipal waste. Dispose of them according to

the laws in your area.

ABOUT CE

Versions of the OPC-2389 which have the “CE”

symbol on the product comply with the essential

requirements of the 2014/30/EU directive for

Electromagnetic Compatibility.

Below statement is for UKCA purpose only

United Kingdom Authorised Importer: Icom (UK) Ltd.

Address: Blacksole House, Altira Park, Herne Bay, Kent,

CT6 6GZ, U.K.

Produkt Specifikationer

Mærke:	Icom
Kategori:	Ikke kategoriseret
Model:	OPC-2389

Har du brug for hjælp?

Hvis du har brug for hjælp til Icom OPC-2389 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Icom Manualer

Icom ST-ID50A Manual

1 Juli 2025

Icom ST-4003A Manual

1 Juli 2025

Icom CT-M500 Manual

27 Juni 2025

Icom OPC-478UD Manual

26 Juni 2025

26 Juni 2025

26 Juni 2025

26 Juni 2025

26 Juni 2025

Icom OPC-2350LU Manual

26 Juni 2025

Icom IC-F6400D Manual

21 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

RADEMACHER Troll Comfort-3D 5635 Manual

1 November 2025

Beverage-Air VueMax VMHC-7-1-B Manual

1 November 2025

SmallRig 4842 Manual

1 November 2025

Ikea TALGJE 702.982.38 Manual

1 November 2025

Lindy 43339 Manual

1 November 2025

Ikea VINTERFINT 805.800.24 Manual

1 November 2025

RADEMACHER RolloTron Schwenkwickler Comfort 1500 Manual

1 November 2025

Lantronix ION C2110 Manual

1 November 2025

Wiesenfield WIE-CHP-110 Manual

1 November 2025

Ikea KLOTTHUJA 105.506.76 Manual

1 November 2025