Imarflex IB-645GS Manual

Imarflex Blender IB-645GS

Læs gratis den danske manual til Imarflex IB-645GS (2 sider) i kategorien Blender. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Imarflex IB-645GS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SPECIFICATION

MODEL NO. : IB-645GS

RATED VOLTAGE : 230Va.c. 60Hz

POWER CONSUMPTION : 500W

CAPACITY : 1500cc

BOX DIMENSION : 350*210*278mm

UNIT DIMENSION : 168*190*392mm

GROSS WEIGHT : 3.3kg

RPM : 23000RPM/Min (±15%)

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed,

including the following:

1. Read all instructions thoroughly.

2. Before using the unit, check if the voltage indicated corresponds with the convenience

outlet (230Va.c.).

3. Do not use the two-way socket with another appliance.

4. Do not use any appliance with a damaged cord or plug. If the cord is damaged it should

be replaced with the same type and size or bring the unit to the nearest Imarflex

Authorized Service Center.

5. Do not place the unit near a gas stove, an electric burner or in a heated oven.

6. Place the unit on stable surface; keep it away from the edge of counter to avoid accident.

7. Children should be supervised to ensure that they do not play with the appliance.

8. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliances by a

person responsible for their safety.

9. The maximum continuous operating time of the blender is one minute only. Do not

exceed with the maximum operating time. It may cause damage to the unit.

10. To protect against electric shock, do not immerse the base in water or any other liquid.

11. Extreme caution must be exercised when using an appliance containing hot liquid in the

blender when blending as it can be ejected out of the appliance due to sudden steaming.

12. Use of accessories or equipment not supplied by the manufacturer may cause damage

or malfunctioning of your appliance or result in injuries.

13. Use on a hard, flat level surface only, to avoid interruption of air flow underneath the

appliance.

14. Carry or move the blender’s tumbler only by its handle.

15. Switch off the appliance and unplug the unit before replacing tumbler or accessories.

16. Blade is sharp, handle it carefully.

17. Do not put the blade assembly on the base without the tumbler.

18. Do not use the blender if the tumbler has a crack.

19. This appliance is not intended for outdoor use.

20. Never place the blender near hot surfaces.

21. In case of malfunctions, please bring the blender to the nearest Authorized Imarflex

Service Center.

22. Avoid water spillage into the socket, connector, cord and alike.

23. Switch off the appliance before removing the glass jar into the motor base.

24. Do not use this unit other than its intended use.

25. For household use only; not intended for any business purposes

26. Save this instruction manual for future reference.

27. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout,

this appliance must not be supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on and off by the utility.

DESCRIPTION OF PARTS:

HOW TO ASSEMBLE:

IMPORTANT: The blender jar and blades are subject to wear during regular use. Always inspect

the jar for nicks, chips or cracks. Always inspect blades for broken, bent or loose blades. Avoid

using the jar or blades if damaged. Contact the Imarflex Authorized Service Center to obtain

evaluation and repair.

Make sure that the blender is unplugged. Place blender base on clean, dry surface to keep foreign

particles from being pulled up into motor during operation.

1. Place the rubber packing into the blade assembly and put the assembly into the jar support.

(See pic.1 & 2).

2. Assemble the jar support

assembly into the glass jar.

3. Put the measuring cup into the lid.

(See pic.3)

4. Secure the lid into the glass jar

and press down. (See pic.3)

5. Put the glass jar on the motor

base, press down and turn

clockwise until securely engaged.

(See pic. 4) Note: The blender will not work if the glass jar is not properly attached to

the unit base.

HOW TO USE:

1. For initial use, wash glass jar with blade assembly thoroughly. “Please refer to cleaning and

maintenance method #2”. Wipe it dry.

2. Put the glass jar with blade assembly on the motor base.

3. Plug the unit into the convenience outlet.

4. Be sure to remove the seeds of the fruits/vegetables if needed.

5. Put the desired mixture.

6. Put the lid on the glass jar and close securely. Place the center lid into the hole of the lid and

push down to lock.

7. Plug the unit into the convenience outlet.

8. Press the pulse button first to crack the ice.

9. Select the desired speed and function.

a. Speed 1 – Function is for blending soft vegetables, soft fruits or any light mixture

b. Speed 2 – Function is for blending hard vegetables and hard fruits or if you desire to blend

smoothie or any alike.

c. Pulse – It is the function to crush the ice.

10. Additional ingredients can be added through opening in the lid.

11. Turn OFF and unplug the unit after every use.

NOTE:

(1) Some electric smell may be observed on first use.

(2) Maximum continuous operating time is 1 minute only.

CAUTION: Always put water or liquid in the jar to avoid damage to the unit. Use pulse function

first, if you are blending with ice.

USEFUL TIPS:

- To achieve the best results when pureeing solid ingredients, place small portions

through the opening in the lid one by one.

- When mixing solid ingredients, start with a small amount of liquid. Gradually add more

liquid through the opening in the lid.

- For stirring solid or very thick liquid ingredients, we recommend that you use the

blender in pulse mode to prevent the blades from being stuck.

CLEANING AND MAINTENANCE:

Motor Base

1. Unplug the unit from the convenience outlet.

2. Wipe or clean the outside surface with a damp or soft cloth.

NEVER IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.

3. Thoroughly clean speed selector knob so that it works freely. It will become sticky when in

use. Use a damp cloth or sponge to flush and clean the groove around the water shielded

switch. You may also lightly spray the surface around the switch with an all-purpose cleaner

and work the switch back and forth a few times to loosen any dried residue under switch.

4. Polish with a soft cloth.

5. Always be sure to wring excess water out of cloth or sponge when cleaning around the

controls or any electrical part.

Lid/Center Lid

Wash in warm soapy water. Rinse by a running water and dry. Reassemble before use.

Container and Blade Assembly:

Method #1

- After use, add warm water and a splash of vinegar to blender jar. Turn ON and let the

blender work the liquid for about a minute. Pour out, rinse the blender jar well.

Method #2

- Fill the blender jar half way with warm water, add a small amount of liquid dish detergent and

turn the unit ON for about 30 seconds. Repeat if needed. Rinse well.

Method #3

- If blender was left sitting until there is dried, crusty food bits inside: fill with warm, soapy

water (or vinegar water) and let sit for about 30 to 60 seconds. Empty water to about half

and then blends for 30 second intervals until clean.

1. Turn OFF the unit and wait for the blade and motor to stop.

2. Always unplug the unit after every use.

3. Remove the blade assembly by turning it clockwise.

4. Wash the rubber packing, blade and jar support with soap and water.

5. Turn the plastic jar upside down to remove excess water.

6. Wipe the plastic jar and blade with soft cloth to dry. Make sure to reassemble the unit

properly before storing it.

7. Never leave food inside the blender jar for a long period of time.

8. Store the blender on a dry cool place.

NOTE: NEVER ALLOW THE BOTTOM OF THE BLADE TO GET WET.

TROUBLE SHOOTING:

REMINDER: Please do not forget to fill up and send the warranty card with receipt to our

email addressimarflexfb@evergoodinc.com

Distributed By: Evergood Unlimited Corp.

901 G.Masangkay St., Manila

Made in China

PROBLEM

CAUSE

SOLUTION

Motor not

working

1. Convenience

outlet is not

working.

2. Damage on the

unit

1. Check the outlet where the

unit is plug in if it is working.

2. Check for any damage.

3. Bring the unit to the nearest

Authorized Imarflex Service

Center

Motor stop

during

operation

1. Overload

protection

activated

1. Unplug and let the unit rest

for at least 1 minute

Smoke and

burnt smell

occurred

1. Unit is use for the

first time

1. Its normal for the first use

Leak on

the bottom

of the jar

1. Rubber packing is

not properly

installed

2. Rubber was

damaged

1. Turn OFF the unit. Remove

the jar and check the rubber.

Reassemble the unit.

2. Replace the rubber with the

new one.

3. Bring the unit to the nearest

Authorized Imarflex Service

Center.

Attachment

not

functioning

1. Not properly install

1. Turn off the unit and

check the assembly

Produkt Specifikationer

Mærke:	Imarflex
Kategori:	Blender
Model:	IB-645GS

Har du brug for hjælp?

Hvis du har brug for hjælp til Imarflex IB-645GS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blender Imarflex Manualer

Imarflex IB-645GS Manual

8 Oktober 2025

Imarflex IB-655GC Manual

13 Juni 2025

Imarflex ICB-2150PRO Manual

2 April 2025

Imarflex ICB-640G Manual

4 September 2024

Imarflex ICB-500B Manual

4 September 2024

Imarflex ICB-500A Manual

4 September 2024

Imarflex ICB-500C Manual

4 September 2024

Imarflex ICB-500 Manual

4 September 2024

Imarflex ICB-450GS Manual

4 September 2024

Imarflex ICB-1900PRO Manual

4 September 2024

Blender Manualer

Nyeste Blender Manualer

Blendjet 2 Manual

7 Oktober 2025

Create FULLMIX BLEND & GO! Manual

4 Oktober 2025

Kogan Vitablast KA2VTABLSTA Manual

3 Oktober 2025

Oster Pro 1200 BLSTMB-GTF-000 Manual

2 Oktober 2025

Oster Beehive 4127 Manual

2 Oktober 2025

Aiwa Saberu Pro ATB-3000 Manual

1 Oktober 2025

ElectriQ iQMix-Platinum Manual

30 September 2025

Aiwa Saberu 2500 ATB-2500 Manual

29 September 2025

Aiwa Saberu 1500 ATB-1500 Manual

29 September 2025

Brentwood JBS-1000BK Manual

29 September 2025