Industrial Music Electronics Kermit Mark III Manual

Industrial Music Electronics Ikke kategoriseret Kermit Mark III

Læs gratis den danske manual til Industrial Music Electronics Kermit Mark III (22 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 74 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 37.5 anmeldelser. Har du et spørgsmål om Industrial Music Electronics Kermit Mark III, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/22

KERMIT MARK III

OPERATIONS MANUAL • FIRMWARE V1.0

FUNDAMENTALS

Kermit is a 4-channel tempo-synced wavetable oscillator (optimized for LFO operation) that has many generation

modes. The A and B channels have full controls and a high sampling rate. The C and D channels have some shared

controls, but with nearly the same capability of the A and B channels. Kermit is only a 12HP module, so the user

interface is economized. Some controls are shared. “Deep” parameters and CV/modulation assignments are made by

using “hotkeys”. Each channel has a button that, when held down, changes the action of all the knobs on the module.

For example, on channels A or B, you can access the deep parameters of ne tune, phase, and waveform bank by

holding down the channel button and turning the frequency, amplitude, or waveform knob respectively.

To assign the channel’s external CV input to a parameter, hold down the rotary encoder’s button and turn the

destination knob. To cross-modulate a parameter with the output of another channel, hold down the source channel’s

button and turn the knob of the desired destination parameter. When any of these hotkey actions are used, a window

will pop up on the display showing the name of the parameter being changed and a visual representation of the

modulation amount. After a few seconds, this popup display will go away and the main screen will reappear. To exit

from the popup sooner, press a nearby channel button.

Channels C and D have limited controls. The single knob for each channel normally controls the coarse frequency.The

following table shows the assignment key combinations necessary to program the modulation matrix for channels C

and D.

Each channel has an LED near its output which displays its absolute voltage from -6V (led OFF) to +6V (led brightest).

When the amplitude of the channel is attenuated, the LED will tend towards medium brightness instead of OFF. Use the

channel at full scale amplitude to make full use of the LED indicator.

SCREEN SAVER

The Kermit’s display is an OLED. It is set to a brightness to provide the best balance between visibility and long

life. To preserve the life and maximum brightness of the OLED, it will turn off if a button or encoder is not used for 10

minutes. To turn it back on, press a button or turn the encoder.

MK III MENU SYSTEM

Most buttons on Industrial Music Electronics modules have hidden menus associated with them. To access them,

hold down the rotary encoder button and push a button. The menu will appear on the display. Turn the encoder to

select the desired menu item. Push the encoder to select the item, and turn the encoder to change the value of the

selected item. Push the encoder button again to enter your selection. Exit the menu by pressing any of the other

buttons. If a button does not have a menu associated with it, then the button press combination will usually invoke

another shortcut function.

The menus for channel C and D are shared, and accessed by the one channel C/D button. To access the channel

D menu, enter the channel C menu and keep scrolling down.

GETTING STARTED

Select modes for each channel. Enter the menu for each channel and look at the parameters "Channel Type" and

"Mode". The Type option selects the class of functions: LFO, oscillator, envelope, random, or S+H. Each oscillator

type has three Modes associated with it Details are given in the "MODE OVERVIEW" section.

MODE SELECT SHORTCUT

Hold down the PRESET button and press one of the channel buttons to increment the channel's mode/type selection.

You can quickly cycle through the 12 possible modes this way. To increment channel D, hold down both the Preset and

Tap buttons, then press the channel C/D button.

HOLD DOWN THE FOLLOWING bUTTONS WHILE TURNING THE C/D kNObS TO ACCESS ALL PARAMETERS:

Amplitude Waveform FIne Tune Phase Wave Bank

A b A+C/D b+C/DC/D

Produkt Specifikationer

Mærke:	Industrial Music Electronics
Kategori:	Ikke kategoriseret
Model:	Kermit Mark III

Har du brug for hjælp?

Hvis du har brug for hjælp til Industrial Music Electronics Kermit Mark III stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Industrial Music Electronics Manualer

Industrial Music Electronics HERTZ DONUT MARK III Manual

4 August 2024

Industrial Music Electronics Kermit Mark III Manual

31 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Miele WTV 417 Manual

10 Oktober 2025

Miele EBA 7747 Manual

10 Oktober 2025

Panasonic MX-HG4401 Manual

10 Oktober 2025

Fresh 'n Rebel Selfie Stick Manual

10 Oktober 2025

TOA VX-3308WM Manual

10 Oktober 2025

Teka EWH 100 DHH Manual

10 Oktober 2025

Xerox App Gallery Manual

10 Oktober 2025

Miele WTV 511 Manual

10 Oktober 2025

Miele WTV 601 Manual

10 Oktober 2025

Miele GaLa-S Manual

10 Oktober 2025