Inno BRA220R Manual

Inno Tagboks BRA220R

Læs gratis den danske manual til Inno BRA220R (2 sider) i kategorien Tagboks. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Inno BRA220R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

5411-71089G

These instructions are for the installation and use of the Inno carrier system attachment. After reading this manual, keep it in a safe place along with the

installation instructions for the rest of your carrier system.

If using an aftermarket base rack system, make sure that it is installed properly

according to the procedures described in the installation instructions for that rack.

The distance between the front and rear crossbars should be at least 60cm ( 2 feet )

Cargo Box BRA220R Installation Instructions

Cargo Box BRA220R Installation InstructionsCargo Box BRA220R Installation Instructions

CAUTION

PRECAUTIONS

Do not overload your cargo box. Maximum load

capacity varies by vehicle. Check the appropriate

limits for your car in the Fit Guide and your vehicle

owner's manual and determine your maximum

loading capacity with the formula below.

The Cargo box includes the parts listed below. Verify that they are included with the

carrier you have purchased. In the event any of these is missing, contact our service

center as listed at the end of this manual.

Before driving the vehicle, shake the rack in

all directions to ensure that there is no

looseness in any of the mounting knobs and

screws. Retighten any loose knobs or screws.

Max load of

cargo box

110 lbs

Max load of

vehicle or

cross bar

Weight of

cargo box

OR -

Ins

tallation

tru

ctions

Use the lower of the 2 options below

Parts

Rooftop Box

QtyNO.

Knob

U-Bolt

Plate

Strap

Hole Covering

Molding

Strap Hook 2

Key

Manual Instruction

234

5 6 7

Temporarily put the Box on cross bars. And Insert key, turn clockwise and ① ②

push button to open the Box. push button

key

Adjust the location of the Box to align with holes at A.

Rooftop Box

Cross Bar

A B

Front

Attach the Box to front cross bar with Plate, U-Bolt and Knobs. Make sure that

the ring on the Plate is on the side nearest the side of box.

U-Bolt

Ring

Plate

Cross Bar A

Front

Ring

Plate

Cross Bar B

Rear

U-Bolt

Tighten right and left knobs alternately to secure the Box to cross bar.

U-Bolt

Knob

Front

U-Bolt

Knobs

Rear

Make sure to tighten the right

and left knobs evenly so that

the U-bolt sits square with the

bar.

If U-bolt is not tightened

correctly, it may allow the box

to come loose.

Warning

U-Bolt

Cargo Box

Cross Bar

Front - Place plugs into the 6 unused holes to seal

Rear - Trim Molding to the proper size and insert into slot.

U-Bolt

Plug

Front

U-Bolt

Cut Molding to this size.

Molding

Rear

Thread Strap trough two Rings on each side of the box and

fasten. Attach Strap Hooks inside box lid just above Straps.

Strap Hook

Box Lid

Buckle

Strap

Buckle Ring

Push Box in all directions to make sure that there is no

loosenesss. If you notice any play in the box, retighten 8 Knobs.

Insert Key into key cylinder and turn it clockwise to "Open" position. Lift Box Lid by

pushing release button.

Release button

Box lid

Key

Leave Key in key cylinder until Box is closed to avoid locking it in the box

accidentally.

Caution

Strap

Strap Hook

Buckle

Unfasten Buckle and hang Straps on Strap Hooks to keep them out of the way while

loading. Load cargo. Unhook Straps and fasten it to secure cargo from moving while

driving.

To close lid, make sure that Key is in the OPEN position. Make sure that Hooks line

up with latches and close Box all the way.

Hook latches

Hook

Try to lift the lid at the latch points shown below to make sure that the hooks

have full engaged with the latches.

Turn Key counter clockwise to the CLOSE position.

Check at these points

Genuine Inno Replacement Parts

Specifications and the appearance of the carrier system and genuine replacement

parts are subject to change without prior notice in the interest of product

improvement.

The following genuine replacement parts are available for this Inno carrier system

component. Specify the part number when ordering parts from your dealer.

Note

Manual

IN NO

ISP952 Strap

(2 pack)

ISP682 Strap Hook

(2 pack)

ISP193 Molding

(2 pack)

Key(Verify

Key number)

U-Bolt Knobs (2 pack) Plate

Instruction Manual

Fit Kit

ISP588 Hole Plugs

(4 pack)

Contact Information

If you have any questions or comments, please contact us at the service center listed below. CarMate shall not be held liable for any accidents or incidental losses arising

from improper installation or use, nor for those arising from installation or use after the customer has made any change to the system's original configuration or specifications.

Car Mate USA

383 Van Ness Ave., Suite 1603

Torrance, CA

www.innoracks.com

support@rv-inno.com