Integral LED ILSTRGBWB030E Manual

Integral LED Lys ILSTRGBWB030E

Læs gratis den danske manual til Integral LED ILSTRGBWB030E (4 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Integral LED ILSTRGBWB030E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Flexible 24V INTEGRAL LED RGBW Strip IP65

Installation Guide

Pour des instructions en français, merci de

vous rendre à l’adresse www.integral-led.

com an de les télécharger directement

depuis la page du produit (‘Product’ sur

le site) dans la section Téléchargement

(‘Download’)

IMPORTANT NOTICE

• This product should be installed according to the instructions in this guide and by a qualied electrical installer.

• All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for the UK or in accordance with all applicable

regulations and laws in the country in which it is being installed. This product falls under a low voltage Class circuit category.III

• Switch OFF power at the mains before installing the LED strip.

• S trip must only be installed indoors or in outdoor areas are sheltered. Unit is protected against water jets and dust. Not suitable for water immersion.

• Avoid looking directly at the strip when turned on, for a long period of time.

• Observe the operating temperature of the LED strip: -25C to +60C.

To avoid any damage to the LED strip or driver

• Always disconnect or switch o the power supply before cutting or connecting an LED strip. Wait at least one minute before connecting to a recently

powered driver.

• Always handle the LED strip with care.

• Observe the correct polarity for 24V connections (g 1).

• Safely route and secure all wires so they cannot be pinched or damaged.

• Do NOT power the strip whilst in its packaging reel.

• Do NOT twist the LED strip or heavily press down on the area above LEDs.

INTRODUCTION

• This installation guide is for exible, IP65 constant voltage self-adhesive LED strips produced by Integral LED.

• Depending on your installation, you can purchase additional accessories such as mounting clips.

A) CHOOSING A 24V LED DRIVER

• This LED strip operates with a 24V DC constant-voltage power supply known as a driver. Drivers are sold separately and are available in varying wattage outputs.

• The specication of the driver required will depend on the total power requirement of the connected strip(s). The power output of the driver (wattage

rating) must be at least 20% higher than the total required wattage of the strip(s) being powered.

For example, if you are installing 5 LED strips of 1M each and the power requirement of each 1M strip is 3W/metre – the total power requirement is 15W.

The power rating of the driver should be a least 20% above 15W i.e. A minimum of 18W

• Ensure the LED driver specication and IP rating is correct for your application.

B) PRE-INSTALLATION GUIDE

LED strips make a great addition to any domestic or commercial environment. They can change the mood and look of a space instantly and are very energy

ecient. The possibilities are endless so the requirement for each lighting project will be dierent.

It is worth taking some time to plan your project for the desired eect before removing the backing tape on the LED strip. The specication, length, mounting position

and distance from an object determines the appearance of a lit LED strip. You will also need to consider the placement and concealment, of the 24V LED driver, control

unit and wires and the power switch to turn the LED strip ON and OFF.

We recommend that you test the strip by temporarily holding the LED strip in place by using a suitable tape, such as masking tape. Safely connect the power

supply - you can then carefully move the strip to try dierent angles and positions to gain the desired illumination eect and position. Check for light spots,

reections and shadows.

Please consider the surface you are applying the LED strip to; the surface should be stable, clean and smooth. On removal of a xed LED strip - damage to

paint, wallpaper or other substrates may occur. Take care in measuring the length required before cutting the strip, take into account the space required for the

connection wires. You may also consider using a spirit level, plumb line or other guide if required.

In the bag

1 X 5M ±5cm IP65 INTEGRAL LED RGBW STRIP on reel pre-tted with an

appropriate connector to connect to a suitable control unit and power

supply.

IP65

WARNING

DO NOT CONNECT THE LED STRIP DIRECTLY TO A MAINS SUPPLY.

THE LED STRIP MUST ONLY BE CONNECTED TO A SUITABLE 24V LED DRIVER.

Produkt Specifikationer

Mærke:	Integral LED
Kategori:	Lys
Model:	ILSTRGBWB030E
Kode for international beskyttelse (IP):	IP65
Type:	Universal stribelys
Bredde:	12 mm
Vægt:	280 g
Antal pr. pakke:	1 stk
Produktfarve:	Beige
Pakkevægt:	285 g
Pakkedybde:	11 mm
Pakkebredde:	180 mm
Driftstemperatur (T-T):	-25 - 60 °C
Husmateriale:	Polykarbonat (PC)
Lampetype:	LED
Certificering:	CE RoHS
Energieffektivitetsskala:	A til G
Strømkilde type:	DC
Monteringstype:	Klæbende tape
Fjernbetjent:	Ja
Energieffektivitetsklasse:	G
Pæreeffekt:	12 W
Understøttet placering:	Indendørs
Lysfarve:	Blue, Green, Red, White
Beskyttelsesklasse:	III
Bæredygtighedscertifikater:	Lavspændingsdirektivet (LVD)
Strålevinkel:	115 °
Pære levetid:	15400 t
Plug and play:	Ja
Dæmpbar:	Ja
Længde:	5000 mm
Driftsspænding:	24 V
Egnet til lys type:	Atmosfære
Integreret LED:	Ja
Farve skiftende:	Ja
Antal lyskilder:	360 pære(r )
Total effekt:	60 W
Farvetemperatur (min.):	4000 K
Farve-gengivelse (CRI):	80
Fleksibilitet:	Ja
Energiforbrug pr. 1000 timer:	12 kWh
Garantiperiode:	3 År