Integral LED ILSTRGBWB043E Manual

Integral LED Lys ILSTRGBWB043E

Læs gratis den danske manual til Integral LED ILSTRGBWB043E (4 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Integral LED ILSTRGBWB043E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Flexible 24V INTEGRAL LED RGBW Strip IP65

Installation Guide

Pour des instructions en français, merci de

vous rendre à l’adresse www.integral-led.

com an de les télécharger directement

depuis la page du produit (‘Product’ sur

le site) dans la section Téléchargement

(‘Download’)

IMPORTANT NOTICE

• This product should be installed according to the instructions in this guide and by a qualied electrical installer.

• All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for the UK or in accordance with all applicable

regulations and laws in the country in which it is being installed. This product falls under a low voltage Class circuit category.III

• Switch OFF power at the mains before installing the LED strip.

• S trip must only be installed indoors or in outdoor areas are sheltered. Unit is protected against water jets and dust. Not suitable for water immersion.

• Avoid looking directly at the strip when turned on, for a long period of time.

• Observe the operating temperature of the LED strip: -25C to +60C.

To avoid any damage to the LED strip or driver

• Always disconnect or switch o the power supply before cutting or connecting an LED strip. Wait at least one minute before connecting to a recently

powered driver.

• Always handle the LED strip with care.

• Observe the correct polarity for 24V connections (g 1).

• Safely route and secure all wires so they cannot be pinched or damaged.

• Do NOT power the strip whilst in its packaging reel.

• Do NOT twist the LED strip or heavily press down on the area above LEDs.

INTRODUCTION

• This installation guide is for exible, IP65 constant voltage self-adhesive LED strips produced by Integral LED.

• Depending on your installation, you can purchase additional accessories such as mounting clips.

A) CHOOSING A 24V LED DRIVER

• This LED strip operates with a 24V DC constant-voltage power supply known as a driver. Drivers are sold separately and are available in varying wattage outputs.

• The specication of the driver required will depend on the total power requirement of the connected strip(s). The power output of the driver (wattage

rating) must be at least 20% higher than the total required wattage of the strip(s) being powered.

For example, if you are installing 5 LED strips of 1M each and the power requirement of each 1M strip is 3W/metre – the total power requirement is 15W.

The power rating of the driver should be a least 20% above 15W i.e. A minimum of 18W

• Ensure the LED driver specication and IP rating is correct for your application.

B) PRE-INSTALLATION GUIDE

LED strips make a great addition to any domestic or commercial environment. They can change the mood and look of a space instantly and are very energy

ecient. The possibilities are endless so the requirement for each lighting project will be dierent.

It is worth taking some time to plan your project for the desired eect before removing the backing tape on the LED strip. The specication, length, mounting position

and distance from an object determines the appearance of a lit LED strip. You will also need to consider the placement and concealment, of the 24V LED driver, control

unit and wires and the power switch to turn the LED strip ON and OFF.

We recommend that you test the strip by temporarily holding the LED strip in place by using a suitable tape, such as masking tape. Safely connect the power

supply - you can then carefully move the strip to try dierent angles and positions to gain the desired illumination eect and position. Check for light spots,

reections and shadows.

Please consider the surface you are applying the LED strip to; the surface should be stable, clean and smooth. On removal of a xed LED strip - damage to

paint, wallpaper or other substrates may occur. Take care in measuring the length required before cutting the strip, take into account the space required for the

connection wires. You may also consider using a spirit level, plumb line or other guide if required.

In the bag

1 X 5M ±5cm IP65 INTEGRAL LED RGBW STRIP on reel pre-tted with an

appropriate connector to connect to a suitable control unit and power

supply.

IP65

WARNING

DO NOT CONNECT THE LED STRIP DIRECTLY TO A MAINS SUPPLY.

THE LED STRIP MUST ONLY BE CONNECTED TO A SUITABLE 24V LED DRIVER.

C) POWER SUPPLY CONFIGURATIONS AND WIRING

1) POWERING THE STRIP

The LED strip is powered by a suitable 24V LED driver. Ensure the power is OFF and that the correct

polarity is observed when wiring the LED driver (Fig 1).

2) VOLTAGE DROP

If the total length of LED strips powered by a single LED driver is too long, you may nd that the LEDs

furthest away from the driver will be unlit or dimmed. To avoid this you will need to use additional

drivers. For instance if you are powering 2 X 5M strips from one driver – you will need to split the run

into separate 5M runs each powered by its own driver.

D) PRECAUTIONS FOR INSTALLING THE INTEGRAL LED STRIP

1. Please check the bag contents before installation.

2. Do not remove the strip from the packaging until ready for installation.

3. Do NOT press on the LEDs or other components during installation (g 4).

4. Do not power the strip before completely releasing it from the reel.

5. Do not twist the LED strip (g 5).

6. Strip must only be installed indoors or in outdoor areas are sheltered. Unit is protected

against water jets and dust. Not suitable for water immersion.

7. If the product needs to be cut to length; please measure carefully and cut squarely at the

appropriate cut marks only using a sharp pair of scissors (g 6).

8. To x the LED strip to a smooth surface; the strip is pre-tted with 3M adhesive backing tape.

Ensure that the mounting surface is clean, dry and free from any oils, grease or wax.

9. The Integral LED strip has excellent exibility but requires the bending diameter to be no

smaller than 50 mm (g 7).

10. The strip is pre-tted with V+/R/G/B/W connection wires at one end. Check the supply

voltage and wire connections to control unit and LED driver before switching the power on.

CAUTION – Twisting, pressing on LEDs, over-bending the strip, cutting at non-cut points,

incorrectly powering the strip or not observing the conditions for the IP65 rating (see important

notice above) will invalidate the warranty (your statutory rights remain unaected).

E) INSTALLATION INSTRUCTIONS

1. To ensure a successful installation - please read the precautions and pre-installation

recommendations above.

2. The mounting surface must be clean, dry and free from dust or grease.

3. Release the LED strip from the package and unreel.

4. Measure and cut the LED strip to the required length (only cut at the cut marks with power

OFF). If strip needs to be cut, please see instructions below to seal the strip (F).

5. Remove the 3M self-adhesive backing tape from the strip gradually during installation.

Do not remove it all at once to avoid the strip becoming entangled and sticking to itself (gs

8 and 9).

6. Stick the LED strip to the mounting surface by pressing on the strip in between components

only. Do NOT press on the LEDs or other components on the strip.

7. Due to the weight of the strip, additional mounting clips must be applied to secure the

strip at aprox. 25cm intervals (g 10). Avoid covering the LEDs with the mounting clips. The

mounting clips are sold separately without screws and it is the responsibility of the installer

to select the correct type of screw depending on mounting substrate.

8. Once the strip is axed, it is then ready to be wired. Please see section C1.

F) CUTTING THE IP65 STRIP

The silicone (sold separately) is required to maintain the IP65 rating. For control, always apply the

nozzle ( cut the nozzle 4-5mm from the top). Wear protective gloves and eyewear. Always work on

a protected surface in case of spills. Work in a well-ventilated area. We recommend that the strip is

allowed to dry for 24hrs and 7 days to cure before subjecting the strip to water.

1) If the strip needs to be cut to length or into two or more lengths, all non-powered ends have

to be sealed using a silicone sealant.

a. Cut the non-powered end of the strip squarely with a sharp pair of scissors at the cut marks

Typical installation conguration

Straight run

An LED driver powers the control unit and the rst LED strip. Additional strips

can be connected in series. The installer will need to consider voltage drop

(see 2).

g 2

Powered from the centre

Power one or two equal lengths of LED strip from the centre.

This conguration will give the best results.

g 3

Additional accessories (sold separately) may be required for complex congurations.

2 0 0 - 2 4 0 V A C

D C + 2 4 v D C

D C - D C -

D C +

V +

L E D

D R

L E D

C) 1 (g 1) D = Driver, R = Receiver

C) 1 (g 2) D = Driver, R = Receiver

C) 1 (g 3) D = Driver, R = Receiver

Max Run = 5 Meters

D) 3 (g 4)

D) 5 (g 5)

D) 7 (g 6)

D) 9 (g 7)

E) 5 (g 9)

E) 5 (g 8)



>=50mm

Produkt Specifikationer

Mærke:	Integral LED
Kategori:	Lys
Model:	ILSTRGBWB043E
Kode for international beskyttelse (IP):	IP65
Type:	Universal stribelys
Bredde:	12 mm
Vægt:	280 g
Antal pr. pakke:	1 stk
Pakkevægt:	285 g
Pakkedybde:	16 mm
Pakkebredde:	180 mm
Driftstemperatur (T-T):	-25 - 60 °C
Husmateriale:	Polykarbonat (PC)
Lampetype:	LED
Certificering:	CE RoHS
Strømkilde type:	DC
Monteringstype:	Klæbende tape
Nem at installere:	Ja
Fjernbetjent:	Ja
Pæreeffekt:	12 W
Understøttet placering:	Indendørs
Lysfarve:	Blue, Green, Red, White
Beskyttelsesklasse:	III
Bæredygtighedscertifikater:	Lavspændingsdirektivet (LVD)
Strålevinkel:	115 °
Pære levetid:	13000 t
Plug and play:	Ja
Dæmpbar:	Ja
Længde:	5000 mm
Egnet til lys type:	Atmosfære
Integreret LED:	Ja
Farve skiftende:	Ja
Antal lyskilder:	360 pære(r )
Total effekt:	60 W
Farvetemperatur (min.):	7000 K
Fleksibilitet:	Ja
Garantiperiode:	3 År
LED-chip:	5050