Integral LED ILSTWHIA101E Manual

Integral LED Lys ILSTWHIA101E

Læs gratis den danske manual til Integral LED ILSTWHIA101E (4 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Integral LED ILSTWHIA101E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

2±0.2m

350±5mm 16.67±0.2mm

5010±10mm

6±0.2mm

100±1mm

24V



Flexible 24V INTEGRAL LED Bendy Strip IP20

Installation Guide

IMPORTANT NOTICE

• This product should be installed according to the instructions in this guide and by a qualied electrical installer.

• All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for the UK or in accordance with all applicable

regulations and laws in the country in which it is being installed. This product falls under a low voltage Class III circuit category.

• Switch OFF power at the mains before installing the LED strip

• Strip must only be installed indoors, in a dry area

• Avoid looking directly at the strip when turned on, for a long period of time

• Observe the operating temperature of the LED strip: -25C to +60C

To avoid any damage to the LED strip or driver;

• Always disconnect or switch o the power supply before cutting or connecting an LED strip.

Wait at least one minute before connecting to a recently powered driver.

• Always handle the LED strip with care.

• Observe the correct polarity for 24V connections, positive (+ RED) to positive and negative (–BLACK) to negative.

• Safely route and secure all wires so they cannot be pinched or damaged

• Do NOT power the strip whilst in its packaging reel

• Do NOT touch the LEDs on the strip surface

• To avoid damage or malfuction, DO NOT coat the LED strip with pount, varnish or similar.

INTRODUCTION

• This installation guide is for exible, IP20 constant voltage self-adhesive LED strips produced by Integral LED.

• Unlike standard LED strip, Integral LED Bendy Strip can be bent on dierent axis allowing easy installation to non-linear shape such as furniture or

signage letters.

• The LED Strip is dimmable with a suitable driver and dimmable controller.

A) CHOOSING A 24V LED DRIVER

• This LED strip operates with a 24V DC constant-voltage power supply known as a driver. Drivers are sold separately and are available in varying wattage

outputs.

• The specication of the driver required will depend on the total power requirement of the connected strip(s). The power output of the driver (wattage

rating) must be at least 10% higher than the total required wattage of the strip(s) being powered.

For example, if you are installing 2 LED strips of 1M each and the power requirement of each 1M strip is 6.6W/metre – the total power requirement is 13.2W.

The power rating of the driver should be a least 10% above 13.2W i.e. A minimum of 15W

• Recommended cable specication: 2x0.5mm

2, when cables are required between strip and LED driver.

B) STRIP PROFILE

In the bag

1 X 5M IP20 INTEGRAL LED STRIP on reel pre-tted with an

appropriate connector to connect to a suitable power supply.

IP20

Integral Partcode Colour/Temp.

ILSTWHIA0100E 3000K

ILSTWHIA0101E 4000K

ILSTWHIA0102E 6500K

WARNING

DO NOT CONNECT THE LED STRIP DIRECTLY TO A MAINS SUPPLY.

THE LED STRIP MUST ONLY BE CONNECTED TO A SUITABLE 24V LED DRIVER.

Unit: mm

C) PRE-INSTALLATION GUIDE

Integral LED Bendy strips make a great addition to any domestic or commercial environment. The

possibilities are endless so the requirement for each lighting project will be dierent.

It is worth taking some time to plan your project for the desired eect before removing the backing

tape on the LED strip. The specication, length, mounting position and distance from an object

determines the appearance of a lit LED strip. You will also need to consider the placement and

concealment, of the 24V LED driver and wires, and the power switch to turn the LED strip ON and

OFF.

We recommend that you test the strip by temporarily holding the LED strip in place by using a

suitable tape, such as masking tape (do not apply the tape on LED). Safely connect the power supply

- you can then carefully move the strip to try dierent angles and positions to gain the desired

illumination eect and position. Check for light spots, reections and shadows.

Please consider the surface you are applying the LED strip to; the surface should be stable, clean

and smooth. On removal of a xed LED strip - damage to paint, wallpaper or other substrates may

occur. Take care in measuring the length required before cutting the strip, take into account the

space required for the connector. You may also consider using a spirit level, plumb line or other

guide if required.

D) POWER SUPPLY CONFIGURATIONS AND WIRING

1) POWERING THE STRIP

The LED strip is powered by a suitable 24V LED driver. Ensure the power is OFF and that the correct

polarity is observed when wiring the LED driver. (Fig 1)

2) VOLTAGE DROP

If the total length of LED strips powered by a single LED driver is too long, you may nd that the LEDs

furthest away from the driver will be unlit or dimmed. To avoid this you will need to use additional

drivers. For instance if you are powering 2 X 5M strips from one driver – you will need to split the run

into separate 5M runs each powered by its own driver.

E) PRECAUTIONS FOR INSTALLING THE INTEGRAL LED STRIP

1. Please check the bag contents before installation.

2. Do not remove the strip from the packaging until ready for installation.

3. Do NOT touch or press the LEDs or other components during installation (g 4).

4. Do not power the strip before completely releasing it from the reel.

5. Do not install the product in an environment, which exposes it to direct sunlight, rain, water,

moisture or other particles.

6. If the product needs to be cut to length; please measure carefully and cut squarely at the

appropriate cut marks only using a sharp pair of scissors (g 5).

7. To x the LED strip to a smooth surface; the strip is pre-tted with 3M adhesive backing tape.

Ensure that the mounting surface is clean, dry and free from any oils, grease or wax.

8. The strip is pre-tted with positive and negative connection wires at one end. Check the

supply voltage and wire connections before switching the power on.

CAUTION – Pressing on LEDs, cutting at non-cut points, incorrectly powering the strip or

exposing a standard strip (IP20) to water, particles or direct sunlight will invalidate the warranty

(your statutory rights remain unaected).

F) INSTALLATION INSTRUCTIONS

1. To ensure a successful installation - please read the precautions and pre-installation

recommendations above.

2. The mounting surface must be clean, dry and free from dust or grease.

3. Release the LED strip from the package and unreel.

4. Measure and cut the LED strip to the required length (only cut at the cut marks with power

OFF).

Typical installation conguration

Straight run

An LED driver powers the rst LED strip. Additional strips can be connected

in series. The installer will need to consider voltage drop. The maximum run

length is 5 metres (see 2).

g 2

Powered from the centre

Power one or two equal lengths of LED strip from the centre.

This conguration will give the best results.

g 3

Additional accessories (sold separately) may be required for complex congurations.

D R I V E R

200-240V AC

- V

+ V

- V

+ V

L E D 1

D) 1 (g 1)

D R I V E R

Max Run = 5 Metres

D) 1 (g 2)

D R I V E R

D) 1 (g 3)

E) 6 (g 5)

F) 5 (g 6)

E) 3 (g 4)

24V DC

Produkt Specifikationer

Mærke:	Integral LED
Kategori:	Lys
Model:	ILSTWHIA101E
Kode for international beskyttelse (IP):	IP20
Type:	Universal stribelys
Bredde:	6 mm
Vægt:	100 g
Antal pr. pakke:	1 stk
Produktfarve:	Hvid
Pakkevægt:	500 g
Pakkedybde:	2 mm
Pakkebredde:	210 mm
Driftstemperatur (T-T):	-25 - 60 °C
Husmateriale:	Polykarbonat (PC)
Lampetype:	LED
Certificering:	CE RoHS
Energieffektivitetsskala:	A til G
Strømkilde type:	DC
Monteringstype:	Klæbende tape
Nem at installere:	Ja
Fjernbetjent:	Ja
Energieffektivitetsklasse:	F
Pæreeffekt:	6.6 W
Understøttet placering:	Indendørs
Lysfarve:	Kold hvid
Beskyttelsesklasse:	III
Bæredygtighedscertifikater:	Lavspændingsdirektivet (LVD)
Lysstrøm:	560 lm
Strålevinkel:	115 °
Pære levetid:	25000 t
Plug and play:	Ja
Dæmpbar:	Ja
Længde:	5000 mm
Driftsspænding:	24 V
Egnet til lys type:	Atmosfære
Integreret LED:	Ja
Antal lyskilder:	300 pære(r )
Total effekt:	33 W
Farvetemperatur (min.):	4000 K
Farve-gengivelse (CRI):	90
Fleksibilitet:	Ja
Energiforbrug pr. 1000 timer:	7 kWh
Garantiperiode:	3 År
LED-chip:	2835