Intellinet 509091 Manual

Intellinet Ikke kategoriseret 509091

Læs gratis den danske manual til Intellinet 509091 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Intellinet 509091, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Installation Manual
Type：
：
：
：：NDR DIN rail power supply（
（
（
（（Series：
：
：
：：NDR-75, 120, 240, 480）
）
）
））
NDR-75-12 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 12V 6.3A
NDR-75-24 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 3.2A
NDR-75-48 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 1.6A
NDR-120-12 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 12V 10A
NDR-120-24 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 24V 5A
NDR-120-48 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 48V 2.5A
NDR-240-24 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 24V 10A
NDR-240-48 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 48V 5A
NDR-480-24 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 24V 20A
NDR-480-48 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 48V 10A
Introduction
NDR is a DIN rail power supply series with an economical price and slim design. Like other Mean Well’s DIN series,
they can be mounted on a TS35 Standard DIN rail.
Installation
（ ）1 Always allow good ventilation clearances, 5mm left and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheating. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
（ ）2 The appropriate mounting orientation for the unit is vertical, the input terminals at the bottom and output on
the top. Mounting orientations other than that, such as upside down, horizontal, or table-top mounting, is not
allowed.
（ ）3 Use copper wire only, and recommended wires are shown as below.
AWG 18 16 14 12
Rated Current of
Equipment (Amp) 7A 10A 15A 20A
Cross-section of
Lead(mm2 ) 0.8 1.3 2.1 3.3
Note: Current each wire carries should be de-rated to 80% of the current suggested
above when using 5 or more wires connected to the unit.
Make sure that all strands of each stranded wire enter the terminal connection and the screw terminals are
securely fixed to prevent poor contact. If the power supply possesses multi-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
（ ）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.
（ ）5 Recommended wire strapping length is 5mm (0.197”).
（ ）6 Recommended screwdriver is 3mm, slotted type.
Installation Manual
3
12
4
（ ）7 The recommended torque setting for terminals is shown as below.
Model I/P O/P
NDR-75 6.9 kgf-cm (6 Lb-in) 6.9 kgf-cm (6 Lb-in)
NDR-120 7.5 kgf-cm (6.5 Lb-in) 7.5 kgf-cm (6.5 Lb-in)
NDR-240 7.5 kgf-cm (6.5 Lb-in) 7.5 kgf-cm (6.5 Lb-in)
NDR-480 10.35 kgf-cm (9 Lb-in) 10.35 kgf-cm (9 Lb-in)
（ ）8 Suggested fuse and maximum number of the PSUs that can be connected to a circuit breaker at 230V are shown
as below.
Model Fuse Circuit breaker
C16 D16
NDR-75 T3.15A/L250V 6 13
NDR-120 T4A/L250V 5 10
NDR-240 T5A/L250V 4 10
NDR-480 T8A/L250V 3 5
（ ） ：9 Mounting Instruction
Mount as shown in figure only, with input terminals down, or else sufficient cooling will not be possible.
Admissible DIN rail TS35/7.5 or TS35/15 ：
For rail fastening：
（ ）a Tilt the unit slightly rearwards.
（ ）b Fit the unit over top hat rail.
（ ）c Slide it downward until it hits the stop.
（ ）d Press against the bottom for locking.
（ ）e Shake the unit slightly to check the locking action.
（ ）10 For other information about the products, please refer to www.meanwell.com for details.
Warning / Caution !!
（ ）1Risk of electrical shock and energy hazard. All failure should be examined by a qualified technician. Please do
not remove the case of the power supply by yourself!
（ ）2Risk of electric arcs and electric shock (danger to life). Connecting both the primary and the secondary sides
together is not allowed.
（ ）3Risk of burn hazard. Do not touch the unit in operation and shortly after disconnection!
（ ）4 Risk of fire and short circuit. The openings should be protected from foreign objects or dripping liquids.
（ ）5 Only install the unit in a pollution degree 2 environment (Note.1).
（ ）6 Please do not install the unit in places with high moisture or near the water.
"Click"

Produkt Specifikationer

Mærke: Intellinet
Kategori: Ikke kategoriseret
Model: 509091

Har du brug for hjælp?

Hvis du har brug for hjælp til Intellinet 509091 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Intellinet Manualer

Intellinet

Intellinet 713191 Manual

31 Juli 2025
Intellinet

Intellinet 712996 Manual

31 Juli 2025
Intellinet

Intellinet 561730 Manual

31 Juli 2025
Intellinet

Intellinet 713078 Manual

31 Juli 2025
Intellinet

Intellinet 715768 Manual

30 Juli 2025
Intellinet

Intellinet 713153 Manual

30 Juli 2025
Intellinet

Intellinet 713160 Manual

30 Juli 2025
Intellinet

Intellinet 712958 Manual

30 Juli 2025
Intellinet

Intellinet 712965 Manual

30 Juli 2025
Intellinet

Intellinet 713139 Manual

30 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

RGV

RGV AF-XXL Manual

24 August 2025
Candy

Candy TX60PET 011 Manual

24 August 2025
Deye

Deye SUN1000G3-EU-230 Manual

24 August 2025
Deye

Deye SUN-4K-G Manual

24 August 2025
Candy

Candy HWP 49AMBCR/1-S Manual

24 August 2025
Revitive

Revitive Pro Health 5572AQ Manual

24 August 2025
Vonroc

Vonroc GS501XX Manual

24 August 2025
Candy

Candy NRE H10A2TCBEXSS Manual

24 August 2025
Candy

Candy H5WPB69AMBC/1-S Manual

24 August 2025
Vonroc

Vonroc S2_CF501DC Manual

24 August 2025