Intermatic ET2805CP Manual

Intermatic Ikke kategoriseret ET2805CP

Læs gratis den danske manual til Intermatic ET2805CP (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Intermatic ET2805CP, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
Electronic 1-Circuit
Astronomic 7-Day Time Switch
Installation and Setup Instructions
With 100-Hour Backup
Federal Communications Commission (FCC) Notice for ET2000 Series Time Switches
Description
This document explains the setup and conguration of the Intermatic ET2805 1-Circuit
Electronic Astronomic 7-Day Time Switch. The ET2805 time switch automatically switches
loads according to the entered weekly schedule. The time switch can support up to 48
be applied to any combination of days.
The time switch features an LCD and panel-mounted control buttons to set, review, and
monitor the time switch functions, including setting date and time, schedule creation,
enabling or disabling Daylight Saving Time (DST) and conguring DST switchover dates.
Follow these instructions to complete the installation and programming of the ET2805 time
switch.
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause
undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and radiates radio frequency energy and, if
not installed and used in accordance with instructions, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference that requires the user to correct at his or her own expense.
MODELS ET2805C, ET2805CR, ET2805CP
Shown in indoor/outdoor
lockable metal enclosure
NOTICE
• Do NOT touch circuit board components, contact can create a static discharge, which can damage these electronic components.
• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.
• More than one circuit breaker or disconnect switch may be required to de-energize the equipment before servicing.
• For plastic enclosures, bonding between conduit connections is not automatic and must be provided as part of the installation.
• Installation and/or wiring must be in accordance with National and Local Electrical Code requirements.
• Use #14-#8 AWG wires, rated at least 105°C - COPPER conductors ONLY.
• If the power disconnect point is out of sight, lock it in the OFF position and tag it to prevent unexpected application power.
• Make sure there is no wire insulation under the terminal plate on the time switch connector. Firmly tighten terminal screws.
• For outdoor locations or wet locations (rain-tight), conduit hubs that comply with requirements of the UL514B (standard for fitting conduit and
outlet boxes) are to be used.
• Do not remove insulator that is covering terminals.
• Do NOT exceed maximum current carrying capacity.
• KEEP DOOR CLOSED AT ALL TIMES when not servicing.
Risk of Fire or Electric Shock
WARNING
AC IN
NO-1 COM1
CIRCUIT 1
TIMER
POWER
L1
L2/N
OUTPUT 1
INDIVIDUAL 120/277 VAC LOADS
OUTPUT CONFIGURATION: IND
INPUT 1
AC IN
TIMER
POWER
L1
L2/N
POWER TO TIMER
120/277 VAC
(AUTO VOLTAGE, NO JUMPERS REQUIRED)
Latch location
Tilt top forward
Installation
Follow these instructions to install the time switch.
1. Open the time switch enclosure door.
2. Remove and retain the screw that secures the plastic insulator.
3. Lift the left side of the plastic insulator and pivot away to expose the terminal strip.
4. Press the latch at the top of the enclosure and pull out the mechanism from the
enclosure.
5. Choose and remove the selected knockout(s) from the enclosure.
NOTE: There are ve 1/2 inch to 3/4 inch combination knockouts available. There are
two on the bottom of the enclosure, one on each side, and one on the rear. If a 3/4
inch knockout is needed, remove the 1/2 inch knockout rst, then the 3/4 knockout.
6. Place the enclosure in the desired location providing space for the enclosure door to
swing open fully.
7. Securely mount enclosure using provided mounting holes.
8. Use appropriately rated ttings for the installation.
9. Snap the mechanism back into the enclosure.
10. Strip 1/2 inch off the supply and load wires. Use AWG #14-#8 copper conductors
rated at least 105ºC. Torque to 15.6 lbf-in.
11. Connect the wires to the proper terminals on the time switch and tighten the screws
rmly (See wiring diagrams).
12. Connect ground wire to grounding terminal at the bottom of metal enclosures.
13. Return the insulator to its original position and replace the screw.
14. Close enclosure door.
15. Apply power to the time switch.
Wiring Diagrams
1/2 inch
Initial Setup
The following sections provide instructions for the initial setup of the time switch.
Programming Overview
The steps to program the time switch include setting the current date, time, Astro zone, Astro events, xed events, DST, and holiday
events, setting the time switch’s operation to AUTO mode, ENERGY SAVER mode or MANUAL mode (only MANUAL mode will
appear if there are no scheduled events) and read or write an event schedule from a USB memory stick.
NOTE: If the time switch is left inactive for ve minutes in a programming mode, it will return to the AUTO mode screen ( icon AUTO
turned on). If no scheduled events are programmed, the time switch will return to MANUAL mode. If the date has not yet been
entered, the time switch will go to the Enter Date Mode.
Setting Date
Follow this procedure below to set the date and time in the time switch.
NOTE: If necessary, hold + or - to scroll through the digits rapidly.
1. Press MODE to scroll through the mode selections until and icons appear at the top of the display. The month SET DATE
ashes.
2. Press + or - to select the current month and then press ENTER/NEXT. The day of the month ashes.
3. Press + or - to select the current day of the month, and then press ENTER/NEXT. The year ashes.
4. Press + or - to enter the current year, and press ENTER/NEXT. The month will ash again.
5. Press MODE to move to the next mode selection.

Produkt Specifikationer

Mærke: Intermatic
Kategori: Ikke kategoriseret
Model: ET2805CP

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic ET2805CP stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Intermatic Manualer

Intermatic

Intermatic ELC4236 Manual

21 August 2025
Intermatic

Intermatic ELC4736 Manual

20 August 2025
Intermatic

Intermatic ET-NF Manual

20 August 2025
Intermatic

Intermatic ET2825CR Manual

31 Juli 2025
Intermatic

Intermatic EI230W Manual

30 Juli 2025
Intermatic

Intermatic WH40 Manual

30 Juli 2025
Intermatic

Intermatic R8806P101C Manual

30 Juli 2025
Intermatic

Intermatic LC4527 Manual

30 Juli 2025
Intermatic

Intermatic Arista ALC-4B-BT Manual

30 Juli 2025
Intermatic

Intermatic ET2105CR Manual

30 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Cougar

Cougar GX-S Manual

26 August 2025
AccuTemp

AccuTemp Evolution E62403E110 Manual

26 August 2025
Mastercraft

Mastercraft X14V Manual

26 August 2025
Tefal

Tefal Delfini Plus TT131E Manual

26 August 2025
Saris

Saris Guardian 2 Manual

26 August 2025
Telestar

Telestar HW1 Manual

26 August 2025
Sauermann

Sauermann Si-RS1 Manual

26 August 2025
Tefal

Tefal Subito CM5S1D Manual

26 August 2025
Maxview

Maxview Roam Campervan MXL056 Manual

26 August 2025
Mr Coffee

Mr Coffee BVMC-IHC Manual

26 August 2025