Intermatic PF1103 Manual

Intermatic Ikke kategoriseret PF1103

Læs gratis den danske manual til Intermatic PF1103 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Intermatic PF1103, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION

OPERATION &

SERVICE MANUAL

Model: PF1103 FREEZE PROTECTION CONTROL

IN RAINPROOF (TYPE 3R) ENCLOSURE

Model: PF1103M FREEZE PROTECTION CONTROL MECHANISM

SUITABLE FOR POOL/SPA EQUIPMENT CONTROL

INPUT VOLTAGE: 120 VOLT - 60 HZ OR 240 VOLT - 60 HZ.

ELECTRICAL RATING: 3 HP - 240 VOLT AC.

DANGER! To Reduce the Risk of Injury:

...do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times.

...test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a qualified

service technician.

...always disconnect electricity before servicing this control or the equipment(s) connected to it. THIS CONTROL IS NOT

TO BE USED AS A POWER DISCONNECT.

READ, FOLLOW & SAVE THIS INSTRUCTION MANUAL

GENERAL INFORMATION

Model PF1103 Freeze Protection Control is self-contained in an indoor-outdoor, beige, rainproof

enclosure and designed to be connected to a timing or switching device. Together, they control as well

as protect the Pool/Spa equipment and

plumbing against freeze damage. The Control,

if wired according to instructions, turns ON

the Filter Pump when the air

temperature (where this Control is

located) drops below the temperature

set by the thermostat dial (between

32˚F and 45˚F). Nevertheless, the

Control is not intended to be a

substitute for the insulation, coverings or

maintenance.

Model PF1103M is a mechanism only,

functions just like Model PF1103 and

fits (snaps into) any Intermatic Pool

Panel, Models T10000R, T30000R or

T40000R Series. Both models are

designed to operate either on 120 Volt

or 240 Volt, 60 cycle. When used on

240 Volt however, the neutral wire must be

installed and it is not recommended for

controlling 240 Volt GFCI protected

equipment. For such application, use

Model PF1102 or PF1102M Freeze

Protection Control.

FREEZE PROTECTION

FOR POOLS, SPAS

AND WATER FEATURES

158PF11834.indd 1 3/24/09 9:00:32 AM

IMPORTANT SAFETY INSTRUCTIONS

When installing and operating this Product and other associated equipment, basic safety precautions should always be

followed.

1. This Control must be installed by a qualified person, according to National and Local Electrical Codes.

2. Install this Control not less than 5 feet (3 meters in Canada) from inside edge of pool and 1 foot (30cm) above ground.USE

COPPER CONDUCTORS ONLY rated minimum 75˚ C.

3. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of conductors.

4. For Control grounding, bonding, installing and the wiring of underwater lights, refer to Article 680 of the National Electrical Code

or Article 68 of the Canadian Electrical Code.

5. The Control should not operate any equipment which would cause bodily injury or property damage should it be activated

unexpectedly.

INSTALLATION - MODEL PF1103

1. Select the proper location for theoutdoor

Freeze Protection Control and prepare the

necessary conduit run(s) required by the

installation layout.

2. Hang enclosure on a flat vertical surface or

other support, preferably next to the Switching

Device, using hardware

suitable for the purpose.

3. Properly terminate

conduits at both ends

and pull-in the

conductors as specified by the installation layout.

4. Select the appropriate wiring diagram (120 V.

or 240 V. installation) on page 3 or 4 of this

manual and make LINE and LOAD (Pump)

connections as shown. Wiring the Freeze

Control, first identify each lead by its color

then make wire connections by using wire

nuts. wiring the Time Switch, if it is Intermatic,

follow the diagram. Make connections to

terminal block as shown, see insert above for

Time Switch made prior to 1984 by Intermatic

or made by another manufacturer or it is an air

switch, first identify the LINE and LOAD

terminals of the control and wire the two

devices in Parallel.

Make sure the installation is properly grounded.

5. If the Freeze Protection Control is installed in

location, where it is exposed to direct sun

most of the day, extend 8 inches of the

copper capillary tube of the thermostat into an

open ended (plastic or metal) conduit, about

10 inches long, installed at bottom of the

enclosure. Handle capillary tube with care!

6. TEST INSTALLATION:

a. Turn the thermostat dial to its lowest setting

and place crushed ice (in plastic bag) inside

capillary coil of Thermostat.

b. Turn ON power to Control Panel, wait one

minute then slowly turn thermostat dial

counterclockwise until Filter Pump starts.

c. Turn power OFF to Control, remove ice,

check wiring, tighten terminal screws if

necessary, reinstall front plate.

d. Turn power ON to Control and set Time

Switch and the Thermostat, see

OPERATION instructions below.

Install mechanism in any Intermatic Pool

Panel with only one Time Switch by snapping

it into the unused mounting bracket, furnished

with the Panel and follow steps 4 to 6 above.

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE INSULATION

CLEARS PRESSURE PLATE

CONDUCTOR

TO SET THERMOSTAT, turn dial, pointing to desired temperature between 32˚F and 45˚F, marked on

the plate. Remember, many variables, such as the location of the Freeze Protection Control, the location

of equipment and the pool or spa, the location and insulation of the plumbing, etc., must be considered

before selecting the “turn ON” temperature of the Filter Pump. Your local pool service professional is the

best source of information. The Thermostat is factory set to turn OFF the Filter Pump when the ambient

temperature rises 5˚F above its set point.

TO SET TIME SWITCH, follow instructions inside Time Switch enclosure cover.

OPERATION

INSTALLATION - MODEL PF1103M

158PF11834.indd 2 3/24/09 9:00:32 AM

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	Ikke kategoriseret
Model:	PF1103

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic PF1103 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Intermatic Manualer

Intermatic K121 Manual

8 Juni 2025

Intermatic EK4227S Manual

8 Juni 2025

Intermatic IG1240RC3 Manual

8 Juni 2025

Intermatic LC4523 Manual

8 Juni 2025

Intermatic IG3240RC3 Manual

8 Juni 2025

Intermatic IG2280 Manual

8 Juni 2025

Intermatic KPT0170 Manual

8 Juni 2025

Intermatic EK4135S Manual

8 Juni 2025

Intermatic EK4336S Manual

8 Juni 2025

Intermatic EK4127S Manual

7 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025

Garritan Harps Manual

14 Juni 2025

Marshall CV-H20-HF Manual

14 Juni 2025

Aiphone IXW-MAA Manual

14 Juni 2025

Rival HM-743 Manual

14 Juni 2025

Lutec Avony Manual

14 Juni 2025

Giordani G-SAFE & PLAY Manual

14 Juni 2025

Gourmia GAF799 Manual

14 Juni 2025

Arendo 307503 Manual

14 Juni 2025

Hughes & Kettner Tube 100 Manual

14 Juni 2025