Intermatic PF1202T Manual

Intermatic Ikke kategoriseret PF1202T

Læs gratis den danske manual til Intermatic PF1202T (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Intermatic PF1202T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

FREEZE PROTECTION

FOR POOLS, SPAS

AND TER FEATURESWA

FREEZE PROTECTION FOR POOLS AND SPAS

By ®

INSTALLATION

OPERATION &

SERVICE MANUAL

MODEL: PF1202T

TWO CIRCUIT POOL EQUIPMENT CONTROL

WITH FREEZE PROTECTION IN RAINPROOF ENCLOSURE

ELECTRICAL RATING: 3 HP MAX. - 240 VOLT, 60 HZ.

SUITABLE FOR POOL/SPA EQUIPMENT CONTROL

DANGER! To Reduce the Risk of Injury:

...do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times.

...test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a qualified

service technician.

...always disconnect electricity before servicing this control or the equipment(s) connected to it. THIS CONTROL IS NOT

TO BE USED AS A POWER DISCONNECT.

READ, FOLLOW & SAVE THIS INSTRUCTION MANUAL

GENERAL INFORMATION

This Pool Equipment Control is designed to automatically operate the Filter Pump, Cleaner Pump

and also to provide freeze protection for the pool equipment. Nevertheless this product is not

intended to be a substitute for insulation, coverings, or maintenance.

THE FILTER PUMP TIME SWITCH is located in the upper left side of the enclosure and operates

the Filter Pump, as set by the trippers on the yellow dial, on a 24 hour schedule. For setting the

schedule, refer to page 3 of this Manual.

THE CLEANER PUMP TIME SWITCH is located in the upper right side of the enclosure and

operates the Cleaner Pump (Booster Pump). The trippers of this

Time Switch should be set so that the operation of the

Cleaner Pump falls within the operation of the

Filter Pump. To avoid equipment damage, the two

Time Switches are interlocked and the Cleaner

Pump would not operate unless the Filter Pump

is already operating.

THE FREEZE PROTECTION THERMOSTAT is

located in the lower left side of the enclosure

and turns ON the Filter Pump when the air

temperature (where the Control Panel is located)

drops below the temperature set by the dial

(between 32˚F and 45˚F).

IMPORTANT SAFETY INSTRUCTIONS

When installing and operating this electrical control and other associated equipment, basic safety precautions should

always be followed, including the following:

1. Read and follow all instructions.

2. This Control must be installed by a qualified electrician, according to National and Local Electrical Codes.

3. Install this Control not less than 5 feet of inside edge of pool. USE COPPER CONDUCTORS ONLY.

4. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of

conductors.

5. For grounding and bonding this Control and the installation, refer to section 680 of the National Electrical Code.

6. The Control should not operate any equipment which would cause bodily injury or property damage should it be

activated unexpectedly.

INSTALLATION

1. Select the proper location for the Control Panel and

prepare the necessary conduit run(s) required by the

installation layout.

2. Remove the four #10 hex head screws from the back

of the enclosure and attach mounting brackets to

enclosure.

3. Hang enclosure on a flat vertical surface or other

support, using hardware suitable for the purpose.

4. Properly terminate conduits

at both ends and pull-in the

conductors as specified by

the installation layout.

5. Follow wiring diagram on page 4 of this Manual,

connect LINE1 and LINE 2 OF THE 240 Volt supply

conductors from a 20 Amp. circuit breaker, either in the

main panel or in this subpanel to TB1 terminal block

(see insert above for proper connection) and the

grounding conductor to the Equipment Grounding

Terminal.

6. Connect Filter Pump leads to terminals 2 and 4 of Filter

Pump Time Switch and Cleaner Pump leads to

terminals 2 and 4 of Cleaner Pump leads to terminals 2

and 4 of Cleaner Pump Time Switch. Connect the

grounding leads of each pump to the Equipment

Grounding Terminal at the bottom of the enclosure.

7. If the Control Panel is installed in location, where it is

exposed to direct sun most of the day, extend 8 inches

of the copper capillary tube of the thermostat into an

open ended (plastic or metal) conduit, about 10 inches

long, installed at bottom of the enclosure. Handle

capillary tube with care!.

8. If required by the heater manufacturer, install fireman

switch kit 156T4042A (not furnished) on Time Switch

Plate and make the fireman switch connections. Use at

least #18 AWG wiring with insulation rated 300 Volt or

higher. Place heater ON/OFF switch on heater to ON

(see Figure 2). Some heaters may require a special

connecting harness, contact heater manufacturer for

details.

9. To install additional wiring devices inside the

enclosure, first remove rectangular knock-out(s) in

dead front. Next, remove hex head screws in back of

enclosure and install stand-offs* in place of screws.

Attach wiring device to stand-offs.

 • Stand-offs are not furnished. Order 21T156A for a set of four (4)

stand-offs and mounting hardware.

10. If external bonding is required, install bonding lug(s) on

bottom of enclosure (156T11047A may be ordered)

and bond installation according to code requirements.

11. TEST INSTALLATION:

a. Turn the thermostat dial to its lowest setting and

place crushed ice (in plastic bag) inside capillary coil

of Thermostat.

b. Turn ON power to Control Panel, wait 20 seconds

then slowly turn thermostat dial counter-clockwise

until Filter Pump starts.

c. Using the manual lever on Cleaner Time Switch,

turn ON-OFF the Cleaner Pump.

d. Turn OFF power to Control Panel, remove ice,

check wiring, tighten terminal screws if necessary,

reinstall time switch insulators and front plate.

e. Turn ON power to Control Panel and set time

Switches and the Thermostat, see OPERATION

instructions on page 3.

Figure 1

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE INSULATION

CLEARS PRESSURE PLATE

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	Ikke kategoriseret
Model:	PF1202T

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic PF1202T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Intermatic Manualer

Intermatic K121 Manual

8 Juni 2025

Intermatic EK4227S Manual

8 Juni 2025

Intermatic IG1240RC3 Manual

8 Juni 2025

Intermatic LC4523 Manual

8 Juni 2025

Intermatic IG3240RC3 Manual

8 Juni 2025

Intermatic IG2280 Manual

8 Juni 2025

Intermatic KPT0170 Manual

8 Juni 2025

Intermatic EK4135S Manual

8 Juni 2025

Intermatic EK4336S Manual

8 Juni 2025

Intermatic EK4127S Manual

7 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Aiphone GT-4ZP Manual

15 Juni 2025

Moulinex Secanto DJAB41 Manual

15 Juni 2025

Blodgett Invoq 201E Manual

15 Juni 2025

Vocopro FIELD-QUAD-H Manual

15 Juni 2025

ORNO OR-DB-MK-175P Manual

15 Juni 2025

Milwaukee M12 HSFSM Manual

15 Juni 2025

Berkel Suprema Salumeria PES370 Manual

15 Juni 2025

Bugaboo Butterfly 2 car seat adapters Manual

15 Juni 2025

ORNO OR-CR-278 Manual

15 Juni 2025

Wahoo BLUE SC Manual

15 Juni 2025