Intermatic ST01A Manual

Intermatic Ikke kategoriseret ST01A

Læs gratis den danske manual til Intermatic ST01A (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Intermatic ST01A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

8. The hours digit of the

current day’s DAWN time

ﬂashes on the display.

• Press + or - to adjust the

hour, as necessary.

• Press ON/OFF to conﬁrm

and advance to the DAWN

minutes digit.

• Press + or - to adjust the minutes, as

necessary

• Press ON/OFF to conﬁrm and advance to the

DUSK hours digit.

• Use the same process for setting the DAWN

time to set the time for DUSK.

Note: Locate the current day’s dusk and dawn times in a

local paper or online. You may deliberately adjust

DUSK and/or DAWN settings up to +/- 120 minutes,

if desired, to cause Astronomic events to always

occur a predictable amount of time before or after the

actual dusk or dawn.

9. The timer loops to the beginning of the SETUP

mode.

• Press ON/OFF repeatedly to review/revise your

settings, or press MODE to exit SETUP.

Programming Events

Note: Program ON and OFF events as separate events.

1. Press MODE until PGM

appears on the display.

2. Press ON/OFF to conﬁrm. An

event number ﬂashes on the

display.

Note: If this is the ﬁrst event,

you will see 01.

3. Press ON/OFF to conﬁrm the

event number. An event type

ﬂashes on the display.

4. Use + to select the event type.

• ON - sets an ON event

• SKIP - stops the event

• OFF - sets an OFF event

5. Press ON/OFF to conﬁrm. An

event time type ﬂashes on the display.

6. Use + to select a time type.

• DAWN

• DUSK

• Fixed Time

Note: To set a Fixed Time, press ON/OFF, then + or - to

adjust the hour. Press ON/OFF. Use the same

process to set minutes.

7. Press ON/OFF to conﬁrm. A day selection ﬂashes

on the display.

ST01/ST01K/EI600

In-Wall Timer with Astro Feature

Installation and User Guide

RATINGS

ST01/ST01K EI600

Operating

Voltage

120-277 VAC, 50/60 Hz

Resistive

(heater)

15 A, 120-277 VAC 20 A, 120-277 VAC

Tungsten

(incandescent)

15 A, 120 VAC; 6 A, 208-277 VAC

Ballast

(ﬂuorescent)

8 A, 120 VAC;

4 A, 208-277 VAC

16 A, 120-277 VAC

Motors 1 HP, 120 VAC; 2 HP, 240 VAC

DC Loads 4 A, 12 VDC; 2 A, 28 VDC

Operating

Temperature

32° F to 104° F (0° C to 40° C)

Dimensions 4 1⁄8” H x 1 3⁄4” W x 1 13⁄16” D

SAFETY SECTION

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect

switch(es) before installing or servicing (including replacing the

battery).

• Installation and/or wiring must be in accordance with national

and local electrical code requirements.

• Use COPPER conductors ONLY.

• Do Not recharge, disassemble, heat above 212° F (100° C),

crush, or incinerate the Lithium battery. Keep out of reach of

children.

• Replace battery with Type CR2 only that is certiﬁed by

Underwriters Laboratories (UL).

• Do NOT use timer to control devices that could have dangerous

consequences due to inaccurate timing, such as: sun lamps,

saunas, heaters, slow cookers, etc.

NOTICE

• Risk of timer damage due to leakage if weak battery is not

replaced promptly.

• Dispose of product per local regulations for disposal of Lithium

batteries.

Spring Grove, Illinois 60081

www.intermatic.com

PRODUCT DESCRIPTION

The ST01 Series and EI600 Series In-Wall Timers

give you versatility in a simple to install, 24/7

programmable package. These timers allow you to

customize your timer schedule with automatic dusk/

dawn, random, and Daylight Saving Time (DST)

programming options for up to 40 ON/OFF events.

The ST01 Series and EI600 Series are incandescent/

ﬂuorescent/CFL/LED compatible. In addition, these

timers can handle any load type and require no

neutral wire connection, making them ideal for any

application, regardless of complexity.

TIMER INTERFACE

Display

Mode button

On/Off button

– button (Decrease)

+ button (Increase)

Reset button

Access door to

battery tray

PRE-INSTALLATION

Before mounting the timer in the wall, install the

supplied battery.

1. Gently pry open the access door, located below

ON/OFF, and remove the battery tray from the

timer.

2. Place the supplied CR2 battery into the battery

tray, matching the battery and markings to + –

the and markings on the tray, then place the + –

battery tray back in the timer.

3. The display initializes, then ﬂashes 12:00 am in

manual mode.

4. Press ON/OFF. The timer “clicks” to conﬁrm it is

ready for programming.

Note: If the display doesn’t ﬂash 12:00 am, check/replace

the battery before proceeding.

NOTES

Read these notes before continuing with the timer

installation and programming process.

• The timer is battery-powered and does not need

AC power for initial setup and programming. For

new installations, it is recommended that you setup

and program your timer before installing it.

• The battery controls the ON/OFF function (“click-

ing” sound) and maintains the time and date. The

screen ﬂashes BATT when the battery strength is

low. When replacing the battery, disconnect AC

power. You will have a few minutes to insert new

batteries before the date and time settings are lost.

All other settings will remain in memory, without

battery or AC power.

• Each ON or OFF setting is an event. Each event

must be programmed separately.

• The MODE menu includes SETUP, PGM (program),

AUTO (automatic), RAND (random), and MAN

(manual). AUTO and RAND modes do not appear

on the menu options until the time of day is set and

at least one ON or OFF event is programmed.

• All menus loop (repeat options when you get to the

end of the menu). When in a speciﬁc Mode, press

ON/OFF to loop within that Mode.

• When using the or buttons to change a ﬂashing + –

setting, hold the button to make the numbers scroll

faster.

• When advancing to the next setting, the timer au-

tomatically saves the data from the previous screen

whether you changed a setting or not. All settings

save automatically after ﬁve minutes.

PROGRAMMING

Follow these steps for initial setup and programming

of the ST01 Series and EI600 Series timers.

Clear All Existing Settings

When ﬁrst setting the timer, it is recommended that

any existing settings be cleared.

1. Press and hold ON/OFF button.

2. Using a paper clip or pen, press and release

the RESET button. The timer displays INIT after

approximately ﬁve seconds.

3. Release the ON/OFF button. All previous settings

are removed.

Initial Setup

1. Press MODE until SETUP

appears on the display.

2. Press ON/OFF to advance to

the next menu item (HOUR).

3. Press + or - to adjust the

ﬂashing menuitem (HOUR).

4. Press ON/OFF to advance to

the next menu item (MINUTES).

5. Repeat steps 3 & 4 to set the

MINUTES, YEAR, MONTH,

andDATE.

Note: After setting the DATE, thecurrent day of the week

ﬂashes. Verify the DAY. If wrong, press + or - to review

and adjust the YEAR, MONTH, and DAY. Press ON/

OFF to conﬁrm.

6. The DST selections (AUTO

or MAN) ﬂash on the display.

• Press + to change the

selection.

–Select AUTO if your

location observes DST.

–Select MAN to disable

automatic DST

adjustment.

• Press ON/OFF to conﬁrm and advance to

ZONE selection.

Note: The remaining settings for initial setup (ZONE, DAWN,

and DUSK settings) are only used for regulating

Astronomic events. There is no need to adjust these

settings if you are not scheduling an Astronomic

event.

7. The ZONE selections* (CENT, SOU, or NRTH)

ﬂash on the display.

• Press + to change the

selection to match

your location on the

map.

• Press ON/OFF to

conﬁrm and advance

to DAWN/DUSK selection.

Note: Astronomic adjustment on this product is designed

for the continental United States. Astronomic

schedules are not recommended for locations

substantially beyond the continental US borders,

including Alaska. For southern Canada, select “NRTH”

zone. For northern Mexico, select “SOU” zone. Please

visit www.intermatic.com for other timer models

offering expanded Astronomic geographic coverage.

NORT

CENTRA

SOUTH

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	Ikke kategoriseret
Model:	ST01A

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic ST01A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Intermatic Manualer

Intermatic EK4536 Manual

12 November 2025

Intermatic LC4521C Manual

11 November 2025

Intermatic OP2GY24 Manual

8 November 2025

Intermatic OP2BK24 Manual

6 November 2025

Intermatic WP1010HMXD Manual

6 November 2025

Intermatic WP1250MXD Manual

5 November 2025

Intermatic OP2BK18 Manual

4 November 2025

Intermatic WP1030MXD Manual

4 November 2025

Intermatic OP5BK24 Manual

4 November 2025

Intermatic OP5GY24 Manual

4 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Topping DX5 Manual

4 December 2025

CyberPower GX150C2 Manual

4 December 2025

SPT SM-1024K Manual

4 December 2025

Novy 990037 Manual

4 December 2025

D&R Hybrid-2 Manual

4 December 2025

Iogear GHDSW4K3 Manual

4 December 2025

FLIR Scout BTS-XR Pro Manual

4 December 2025

Vevor WK320016-1 Manual

4 December 2025

ELO E426554 Manual

4 December 2025

Bosch GHV 18 V Professional Manual

4 December 2025