Intermatic T10000R Manual

Intermatic Ikke kategoriseret T10000R

Læs gratis den danske manual til Intermatic T10000R (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Intermatic T10000R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

T10000R SERIES

POOL/SPA EQUIPMENT CONTROLS

INSTALLATION

OPERATION &

SERVICE MANUAL

CONTROL PANEL WITH TIME SWITCH FOR INDOOR/OUTDOOR USE

Suitable for Pool Equipment Control and for Direct Connection of Underwater Lights

ELECTRICAL RATINGS: See inside Enclosure Door

Many of today’s energy efficient pools and spas utilize

the advantages of a single electrical panel, containing

all the necessary controls for the safe, efficient and

automatic operation of the pool/spa equipment. In

addition, this Panel can also be used to control any

outdoor equipment, sign or pump within its rated

capacity.

The all-weather enclosure contains none, one or two

heavy-duty, industrial grade Time Switches.

Also, it has provisions to install switches inside

as well as a switch or GFCI receptacle on the outside.

The Time Switch can also accommodate an

optional heater control (fireman) switch.

The Control is designed to operate any pump,

within its rated capacity. However, if protection

to prevent dry start is required by the pump

manufacturer, it must be provided in addition

to this Control. Contact pump manufacturer

if not sure and/or for more details.

DANGER! TO AVOID RISK OF INJURY:

...do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times.

...test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA!

Contact a qualified service technician.

...always disconnect electricity before servicing this control or the equipment connected to it.

READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL

GENERAL INFORMATION

INSTALLATION

1. Remove the four #10 hex head screws from the

back of the enclosure and attach mounting brackets

to enclosure.

2. Select the proper location for the Control and hang

enclosure on a flat vertical surface or other support,

using hardware suitable for the purpose.

3. Prepare the necessary conduit runs, terminate them

at both ends and pull in the conductors as specified

by the installation layout.

4. Refer to Figure 1 below;

note that this enclosure

contains one or two Time

Switch(es). To wire the

panel, follow the wiring diagram located inside the

enclosure door. Make sure that connections to time

switch terminals are tight (25 lb.-in. minimum) and

insulation clears the pressure plate - see illustration.

5. If required by the heater manufacturer, install

fireman switch kit 156T4042A (not furnished)

on Time Switch Plate and make the fireman switch

connections. Use at least #18 AWG wiring with

insulation rated 300 Volt or higher. Place heater

ON/OFF switch on heater to ON (see Figure 2).

Some heaters may require a special connecting

harness, contact heater manufacturer

for details.

6. For direct wiring of underwater lights, the

installation must comply with Article 680-21(b)

of the National Electrical Code or in Canada,

Articles 68-060, -062 and -066.

7. To install additional wiring devices inside the

enclosure, first remove rectangular knock-out(s) in

dead front. Next, remove hex head screws in back

of enclosure and install stand-offs* in place of

screws. Attach wiring device to stand-offs.

• Stand-offs are not furnished. Order 21T156A for

a set of four (4) stand-offs and mounting hardware.

8. If external bonding is required, install a bonding

lug at bottom of enclosure and bond installation

according to code requirements.

9. Testing of the installation is optional and recom-

mended only if pump is securely in place and will

not be damaged by this test:

a. Turn the manual lever of the Time Switch to OFF.

b. Turn ON power at breaker panel.

c. Move the manual lever of Time Switch to the

right (ON). Pump should start and run on full speed.

In case of unsatisfactory results, turn OFF power,

check your wiring, refer to Troubleshooting on Page 3.

10. Install front panel over wiring compartment.

The control is now ready for programming,

see OPERATION section on Page 3.

IMPORTANT SAFETY INSTRUCTIONS

When installing and operating this Product and other associated equipment, basic safety precautions should always be followed, including the following:

1. Read and follow all instructions.

2. This Control must be installed by a qualified electrician, according to National and Local Electrical Codes.

3. Install this control not less than 5 feet (3 meters in Canada) from inside edge of pool. USE COPPER CONDUCTORS ONLY.

4. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of conductors.

5. For Control grounding, bonding, installing and the wiring of underwater lights, refer to Article 680 of the National Electrical Code or Article 68 of the

Canadian Electrical Code.