Connect the cables from the Quattro LNB to the input connectors marked with LNB V/L, V/H, H/L and
H/H inputs (pay attention to identification of the Quattro LNB connectors). The multiswitch is equipped
with Terrestrial input. Connect the Terrestrial antenna to this input:
V/H H/L H/H
Terrestrial
input
Satellite - Input
V/L
Terrestrial
input
Satellite - Input
V/H H/L H/HV/L
Terrestrial
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Made in China
Designed in LU
Legacy Out
Unicable Out
TM
Satellite - loop-through output
+
V/H H/L H/HV/L
[+Terrestrial] [+Terrestrial]
There are two output connectors: Legacy and Unicable.
The Legacy output is a standard Universal switching output that allows to connect a legacy receiver that
is not supporting the Unicable protocol.
The Unicable output allows to connect up to 8 receiver tuners – each needs to be allocated one of the
8 user bands supported by the multiswitch.
Each receiver tuner is assigned with 1 out of 8 communication channel frequencies (user band). The
frequencies are listed on the product sticker:
For optimized performance, please follow the recommendations below:
1. use the highest frequency for a wall socket located the nearest to the multiswitch and use the low-
est frequency for wall socket located farest to the multiswitch.
2. If you install less than 8 receiver tuners, use the lowest frequencies first. We also recommend
to keep record of the user bands allocated to the different connections as these user bands will
then have to be set in the receiver. The satellite receivers connected to the multiswitch have to be
Unicable-compatible (usually marked with Unicable™ logo).
Note: Loopthrough outputs that are not used should be terminated with 75ohm DC-blocked
terminations.
Safety
Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A lightning strike
into the antenna may cause dangerous overvoltage over the product’s metallic/conductive parts.
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adaptor.
If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long periods of
time.
When disconnecting the product don’t pull the cable but the plug to prevent damage of the cable (wob-
bly plugs and outlets result in fire risk).
The product shall be serviced by qualified experts only.
Thank you for purchasing Inverto’s advanced Unicable multiswitch and we are certain it will meet your
expectations.
Before installing and operating the product, please read the following instructions and recommenda-
tions. We suggest that you keep this manual for future use.
Warranty
The Unicable multiswitch is designed for the distribution of satellite and terrestrial television and radio
signals in home installations. The warranty does not apply for products used for other purposes than
those specified herein. The user/installer shall be responsible for any damage incurred as a result of not
using the product according to the instructions in this manual.
Installation location
The product shall be installed on a wall or other hard inflammable surface.
The product shall be in no case held only with the connected cables.
Place the product in a dry environment where it is not exposed to rain or running water.
Do not install the product close to heat sources or in places exposed to direct sunlight.
Product installation
The following diagram may assist you when drilling the holes:
To connect the product inputs and outputs use high-quality coaxial cables designed for satellite recep-
tion and F-connectors. Use a high-shielding coaxial cables with minimum 90dB.
If you use wall sockets to loopthrough the 8 user bands, make sure the wall sockets were designed
for satellite reception compatible with Unicable technology and allows bidirectional signal propagation.
The following diagram describes the installation configurations supported by the product:
Quattro
LNB
Terminated
Outputs
AC
AC
Legacy
x8 User bands
UB 7 UB 5 UB 3 UB 1
UB 6 UB 4 UB 2
UB 0
Legacy
x8 User bands
UB 7 UB 5 UB 3 UB 1
UB 6 UB 4 UB 2
UB 0
Power In
20V DC, 380mA
V/H H/L H/H
Terrestrial
input
Satellite - Input
V/L
Terrestrial
input
Satellite - Input
V/H H/L H/HV/L
Terrestrial
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Made in China
Designed in LU
Legacy Out Unicable Out
TM
Satellite - loop-through output
+
V/H H/L H/HV/L
[+Terrestrial] [+Terrestrial]
Power In
20V DC, 380mA
V/H H/L H/H
Terrestrial
input
Satellite - Input
V/L
Terrestrial
input
Satellite - Input
V/H H/L H/HV/L
Terrestrial
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Made in China
Designed in LU
Legacy Out
Unicable Out
TM
Satellite - loop-through output
+
V/H H/L H/HV/L
[+Terrestrial] [+Terrestrial]
2 3
Power In
20V DC, 380mA
V/H H/L H/H
Terrestrial
input
Satellite - Input
V/L
Terrestrial
input
Satellite - Input
V/H H/L H/HV/L
Terrestrial
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Made in China
Designed in LU
Legacy Out
Unicable Out
TM
Satellite - loop-through output
+
V/H H/L H/HV/L
[+Terrestrial] [+Terrestrial]
Power In
20V DC, 380mA
V/H H/L H/H
Terrestrial
input
Satellite - Input
V/L
Terrestrial
input
Satellite - Input
V/H H/L H/HV/L
Terrestrial
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Made in China
Designed in LU
Legacy Out
Unicable Out
TM
Satellite - loop-through output
+
V/H H/L H/HV/L
[+Terrestrial] [+Terrestrial]
Power In - 20V DC, 380mA
+
Unicable OutLegacy Out
V/LV/HH/L H/H
V/L
V/H
H/L
H/H
Terrestrial
loop through
output
Terrestrial
input
Satellite - Input
Satellite - loop-through output
TM
Unicable Cascadable Switch
IDLP-UST111 -CUO1O-8PP
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
