Irox HBR558 Manual

Irox Vejrstation HBR558

Læs gratis den danske manual til Irox HBR558 (4 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Irox HBR558, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

32 33

1. INTRODUCTION

Congratulations on your purchase of the HBR558 radio

weather station. The main appliance displays the weather

forecast, the indoor and outdoor temperature/humidity

and the time and date. The weather data are received by

the external sensor.

The 433 MHz technology used in the appliance means

that no cables are needed between the outdoor sensor

and the main appliance.

The appliance is also equipped with a radio clock. The

time is automatically synchronised with the time signal

transmitter DCF77. If the appliance is located out of the

range of the DCF77 signal, the time and date can also be

set manually.

The appliance has a barometer to reliably calculate the

weather forecast. As a basic principle, the appliance does

not need to be operated. The respective barometric

pressure tendency of the previous 24 hours is depicted

graphically.

WEATHER STATION WITH

WEATHER FORECAST

INDOOR/OUTDOOR RADIO-

THERMO/HYGROMETER

AND RADIO-CONTROLLED

CLOCK

(DCF77)

HBR558

INSTRUCTIONS FOR USE

IROX TE558NL & TS33C MANUAL (3 ENG)

SIZE: W93 X H150 (mm)

BY ROSE KOON 30/04/08

FILM 02/05/08

(3 ENG)-Page 31-45

36 37

3534

2c) PREPARATION OF THE RECEIVER UNIT

1. Open the cover of the battery compartment

2. Insert the 2 batteries (1.5 V, UM-3 or size ‘AA’) in

accordance with the respective polarities.

3. Close the battery compartment again.

2d) BATTERY ‘EMPTY’ DISPLAY

When it is time to replace the battery with a new one,

an indicator [ ] will appear next to the display of the

indoor temperature (batteries receiver unit) or outdoor

temperature (batteries transmitter unit) respectively.

2e) SETTING THE EXTERNAL SENSOR –

THERMO/HYGRO

a. As soon as the batteries are in the outdoor sensor, the

sensor starts to transmit the values measured in

intervals of approx. 45 seconds. The main appliance

also looks for signals (for approx. 2 minutes) as soon

as the batteries are inserted. When the signal from the

outdoor sensor is received, the outdoor temperature

and the air humidity values appear on the display.

b. If no sensor signals are received within 2 minutes,

[ ] then appears on the display. Press the [ ] key

for 3 seconds to initiate a search for the signals of the

external sensor. In this way, you can synchronise the

receiving and transmitting signal between the outdoor

sensor and the main appliance. Important: The

external sensor must be set to channel 1.

A LCD DISPLAY

For the convenient reading of all values.

B MODE KEY (BACK PANEL)

Manual setting of clock / data (if required)

C DOWN KEY ( )

- Reduces settings

- Switch radio signal reception on/off

- New search for the temperature sensor.

D UP KEY ( )

- Increases settings´

- Keep pressed: Changes the display

Barometric pressure – Date (barometric pressure is

not compensated at sea level)

- Changes the display unit for the temperature

display in degrees Celsius (°C) or degrees

Fahrenheit (°F)

E HOLDER FOR WALL HANGING

For wall hanging

F BATTERY COMPARTMENT

For two batteries of the type UM-3 or ‘AA’. 1.5V

alkaline batteries or better are recommended.

G STAND

For setting the appliance up on a table

WIRELESS THERMO • HYGRO

FEATURES OF THE THERMO/HYGRO

TRANSMITTER UNIT HTS33

A LED DISPLAY

Flashes 1 x briefly during signal transmission and 2 x

when battery is running out.

B BATTERY COMPARTMENT

For two batteries of the type UM-3 or ‘AA’. 1.5V

alkaline batteries or better are recommended.

C RESET BUTTON

Resetting of the appliance to the default settings and

after a change of channel.

D TRANSMISSION CHANNEL – SELECTOR

SWITCH

Allocates channel 1, channel 2 or channel 3 to a

sensor

E HOLDER FOR WALL HANGING

For wall hanging

F °C/°F SWITCH

Switching between the temperature display in degrees

Celsius (°C) or degrees Fahrenheit (°F) on the display

unit.

2. PUTTING INTO OPERATION

2a) PLEASE READ BEFORE USE

Please note the following instructions to ensure

optimum operation of the appliances:

- Place the receiver unit and the transmitter unit within

1 metre of one another.

- Please follow the sequence described in 2b and 2e

and wait until the measured value appears on the

display.

- Then install the receiver unit and the external

transmitter unit within the possible range of the

appliances, i.e. within a maximum radius of 30

metres.

Please note that the actual range of the transmitters

depends on the building materials of the respective

building and on the respective position of the

external transmitter unit and that the possible

distance can be greatly reduced from the 30 metres

by external influences (various radio transmitters and

other sources of interference). In such cases, we

recommend that you seek another position for both

the transmitter and the receiver. Sometimes, moving

them by just a few centimetres is sufficient!

Although the external transmitter units are

weatherproof, you should not position them in places

where they are exposed to direct sunlight, rain or

snow.

2b) PREPARATION OF THE EXTERNAL

THERMO/GYRO TRANSMITTER UNITS

1. Remove the cover of the battery compartment.

2. Set channel 1 by moving the sliding switch

(important: only set to channel 1!)

3. Insert the 2 batteries (1.5 V, UM-3 or size ‘AA’) in

accordance with the respective polarities.

4. Press the RESET button (e.g. with a paper clip)

5. Screw down the cover of the battery compartment

again.

Produkt Specifikationer

Mærke:	Irox
Kategori:	Vejrstation
Model:	HBR558

Har du brug for hjælp?

Hvis du har brug for hjælp til Irox HBR558 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Irox Manualer

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

Vejrstation Manualer

Nyeste Vejrstation Manualer

Levenhuk Wezzer SN10 Manual

17 Juni 2025

Levenhuk Wezzer PH20 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH10 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH30 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH50 Manual

16 Juni 2025

Levenhuk Wezzer Air PRO DM20 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH40 Manual

15 Juni 2025

Levenhuk Wezzer PRO LP240 Manual

15 Juni 2025

Levenhuk Wezzer BASE L50 Manual

15 Juni 2025

Levenhuk Wezzer SN70 Manual

15 Juni 2025