J. Rockett Audio Designs APE Manual

J. Rockett Audio Designs Ikke kategoriseret APE

Læs gratis den danske manual til J. Rockett Audio Designs APE (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om J. Rockett Audio Designs APE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

MIX

REPEATS

DELAY

TIME

OUT

YOUR FAVORITE DELAY

INPUT

The APE can be configured in several different ways. The above configuration “A” is the series setup.

This allows you to use the APE in front of your delay. This will introduce the famous EP sound as well

but will not color the delayed notes like in Loop configuration. All of your delay controls will work as

they normally do, however, the APE will function differently. In this configuration the APE acts as a

preamp with no controls it just simply adds the influence of the EP sound which is wider and warmer.

It introduces a fat sound across the spectrum. Since it runs at 22.5v just like a real EP everything in

between the notes is cleaner and clearer. To introduce any controllable effect you must engage

the loop switch. Once the loop switch is engaged the “REC” knob becomes a treble boost and

gain. The “Mix” knob also controls output.

NOTE: Be careful to not crank the repeats control on the APE when in series or it can squeal loudly.

NOTE: When in config A and when the loop is engaged the repeats knob is a treble control, the mix

knob is an output control and the REC knob is a drive control. This is where you can add more EP

type push. This will not be the case when you loop in a delay.

NOTE: When using the APE with delays that do not have a mix control or go 100% wet we

recommend that you use it in the “A” configuration. The APE in the “B” configuration works best with

“flat frequency” digital delays. PT Chip delays and Analog delays seem to work best in the “A”

configuration. We encourage you try all configurations with any delay since we cannot try them all.

You may discover a great setup. The APE was intended to add the EP sound to those digital delays

lacking the warmth and fatness of the analog influence of an old EP, especially those delays that

claim to be a recreation of an EP. A real EP has no output control other than driving the record

head.

OTHER SETUPS: You can run your guitar into the “guitar input” and come out of the standard output

but you can also come out of the send or return. When you use the “Return” as the output you get

a fully bypass-able treble boost/gain controlled by the “REC” knob. When you use “Send” as the

output you get a non bypass-able clean boost controlled by the “REC” knob.

The APE works really well with BASS guitar but try it with everything…..you never know.

CONFIGURATION “A”

AMP

A.P.E. ( nalog reamp xperiment)A P E

MIX

REPEATS

DELAY

TIME

OUT

ALWAYS SET REPEATS

TO ABSOLUTE

MINIMUM OR 1 REPEAT

ALWAYS SET MIX TO

ABSOLUTE MAXIMUM

OR FULLY WET

YOUR FAVORITE DELAY

SET TO

DESIRED

DELAY TIME

The APE can be configured in several different ways. The above configuration “B” is the loop setup.

This allows you to loop your delay into the APE and let the APE take over some of the controls. You

will need to set your delay to 100% MIX or fully wet. You will need to set your repeats to only 1 repeat

or minimum. The APE will handle the repeats and the mix along with the record head level. The

Record head level adds gain to the delayed note. If you set the record head level low and the mix

high you will get cleaner delays. If you set the Record head leave; high and the mix low you will

have grittier delays, please experiment.

NOTE: Be careful to not crank the repeats control on the APE when in loop mode or it can send the

repeats into runaway mode..

The APE can be used in loop configuration or in series just like a typical pedal. Run the APE before

any delay and it will introduce the famous EP sound into your entire signal path. We prefer the APE

at the end of the chain just before a delay and/or reverb in loop or series configuration.

Things to experiment with: Try overdrives or boosts into the loop and you will find some amazing

Guitar Input

ar Output

CONFIGURATION “B”

A.P.E. ( nalog reamp xperiment)A P E

Produkt Specifikationer

Mærke:	J. Rockett Audio Designs
Kategori:	Ikke kategoriseret
Model:	APE

Har du brug for hjælp?

Hvis du har brug for hjælp til J. Rockett Audio Designs APE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret J. Rockett Audio Designs Manualer

J. Rockett Audio Designs El Hombre Manual

16 August 2024

J. Rockett Audio Designs Tim Pierce OD Manual

14 August 2024

J. Rockett Audio Designs Tim Pierce Manual

12 August 2024

J. Rockett Audio Designs Boing Manual

12 August 2024

J. Rockett Audio Designs The Dude Manual

11 August 2024

J. Rockett Audio Designs Archer Manual

10 August 2024

J. Rockett Audio Designs APE Manual

10 August 2024

J. Rockett Audio Designs Touch OD Manual

9 August 2024

J. Rockett Audio Designs Broverdrive Manual

9 August 2024

J. Rockett Audio Designs The Dude V2 Manual

8 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025