Jablotron GC-61 Manual

Jablotron Sikkerhed GC-61

Læs gratis den danske manual til Jablotron GC-61 (4 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Jablotron GC-61, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

GC-61 GSM communicator 1 / 1 MHZ51105

The GC-61 GSM communicator

Installation manual

The GC-61 communicator is designed for communication with an

alarm receiving centre via a GSM network. The communicator receives

data from a control panel via a simulated telephone line. Report codes

are transmitted from a control panel to the GC-61 in Contact ID format.

A SIM card determines the GSM network used. This manual is valid for

version HZ61008.

The GSM module, when installed in the alarm control panel, enables:

• Data transfer to one or two Alarm Receiving Centres (ARC)

• Remote control and programming of the communicator via SMS

instruction messages from a mobile phone or from Jablotron’s SMS

website

• Programming of the communicator via Jablotron’s website

www.GSMlink.cz

• Phone calls using a telephone set attached to the communicator

(via the GSM network)

• An SMS terminal can be used for the easy and convenient

receiving and sending of SMS messages

1. Installation

The communicator can be installed into an alarm control panel or into

a metallic box with a TAMPER switch.

a) Disconnect the control panel’s power supply (both AC and

backup battery). If the control panel has been previously used

before this installation, enter programming mode before

disconnecting the power supply.

b) We recommend you to disable the SIM card PIN code protection

before you insert it into the dialler. Use a mobile phone to perform

this task (if you have a NOKIA phone, select: Menu, Settings,

Security settings, PIN code request, Off). If you insist on using a

PIN, enter PIN 1234.

c) Open the SIM card holder (by sliding it in the direction shown in

the figure 1 below and insert the SIM card into the holder and

close it by sliding it back.

d) Attach the communicator into the control panel case or metallic box

e) Connect the GSM antenna (never switch the power supply on

without a proper antenna)

f) Connect a telephone set to the PHONE connector (or to the

PHONE terminals) together with the SMS terminal if desired. Only

one telephone set can be attached to the dialler. The PHONE

output of the dialler should never be connected to any other

telephone network.

GC-61

connector

GSM network

failure monitoring

telephone dialer

+12V

GND

INP

GSM ANTENNA

Figure. 1

g) The AUX output is switched on if the GSM network is not available

for 15 minutes. AUX can be used as an alarm terminal. (normally

open dry contact, max. 100mA / 60V) – see the figure 1

h) It is possible to connect an external device (tamper, alarm output

etc.) to the INP input. When activated (by disconnection from

GND), then an activation event will be sent to the ARC (in CID

protocol “1”) and a deactivation event will be sent after

reconnecting INP to the GND.

i) Connect the control panel’s power supply. The LED will start

flashing once every 2 seconds when it has successfully registered

to the GSM network (within 1 minute).

If the LED starts flashing quickly, the module was not able to connect

to the GSM network. In this case, switch off the control panel power.

Remove the SIM card and insert it into a mobile phone to confirm

whether it is possible to connect to the network at this location. You

can also select a desired network manually if this option is available.

Ensure that the SIM card does not request a PIN code (or the PIN

code is set to 1234) Once the SIM card works in the mobile phone,

insert it back into the GSM dialler and repeat step i). If the GSM signal

is weak in this area, change the location of the GSM antenna before

you try to re-establish the connection. The level of GSM signal can be

checked by the SMS command “DINFO”.

j) After connection to the GSM network you can call directly from the

attached telephone.

k) Set all the parameters for Alarm Receiving Centre communication.

l) Programming of the GSM dialler is possible by entering

programming sequences via a mobile phone or an attached SMS

terminal. The most convenient programming method however is via

the www.GSMlink.cz website.

2. Alarm Receiving Centre communication

setting:

The dialler can report events to two different Alarm Receiving

Centres (ARCs). Each ARC has its own setting sequences that differ in

parameter p (p=1 for ARC1 and p=2 for ARC2). Primary and backup

telephone or IP numbers can be set for each ARC. The dialler uses

Ademco Contact ID format and it is also equipped for the future use of

GPRS data transfers. The product is ready to report events to an ARC

based on either landline or GSM data transfer.

The GC-61 re-sends original report codes – the content is not modified

except the Account ID. The communicator forwards original CID

protocol report codes with separator constants 18 and 98 to the ARC

(the constants are converted to 18 during forwarding). Otherwise, their

contents are not altered except for the installation number, which is set

according to communicator settings. The time of a sent event is

generated by the GC-61. The system time is set when the first SMS is

received by GC-61.

Every SMS command must begin with a service access code.

Several setting sequences can be sent within a single SMS.

Sequences must be separated by a comma or space.

2.1. Digital dialler setting

The digital dialler must be set to:

format : Contact ID

ARC telephone number (DTMF): 002

2.2. GPRS setting

GPRS data communication can be used for transmitting events to an

ARC or for connection to the web page www.gsmlink.cz (see section

3). GPRS must be activated on the SIM card. It is also necessary to

set the name and APN in the communicator (for detailed information

ask your GSM provider).

GPRS xxx,yyy,zzz,

where: xxx is the APN

yyy is a the user name (when not used, insert a space)

zzz is a password (when not used, insert a space)

Example: If the name and password are not required and the APN is

“internet”, then the sequence is: 0000 GPRS internet, , ,

2.3. Setting the service remote access code

PG0 xxxxxxxx

Where: xxxxxxxx is a numerical code of 1 to 8 figures

Default setting: 0000 (4 zeros)

2.4. Entering ARC phone numbers (IP addresses)

Primary and back up telephone numbers can be entered for each

ARC:

Primary number: PG1p xx....x

Back up number: PG2p xx....x

where:

GC-61 GSM communicator 2 / 2 MHZ51105

p 1 = ARC1, 2 = ARC2

xxx...x is a telephone number (max. 20 digits) or an IP

address plus port beginning with a #. The IP plus port

must be specified by exactly 4x3 + 5 = 17 digits using

zeros for left-hand bit stuffing, if necessary.

Examples:

(a) 123456789 can be entered as the ARC2 primary number by

entering: 0000 PG12 123456789.

(b) IP address 192.168.1.123 together with port 8080 are set as the

ARC1 primary number by entering PG11#192 168 001 123 08080.

Default setting: No phone number or IP address is set.

2.5. Account ID setting

An ARC uses this ID number for alarm system identification:

PG3p zzzz

where: p 1=ARC1, 2=ARC2

zzzz is the account ID number (z = numbers from 0 to 9 or

A=F1, B=F2, C=F3, D=F4, E=F5 a F=F6,

hexadecimal)

Default setting: ID is 0000 for both ARCs

Note: When an Account ID for ARC1 and ARC2 are not set, it will be

set according to the first received event from a control panel.

2.6. Selecting the ID number

It is possible to select the ID number of the GC-61 or the ID number of

the attached landline communicator for transmission to an ARC.

PG94 x

where:

x=0 The ID number of the GC-61 is used for alarm system

identification.

x=1 The ID number of the attached landline communicator

is used for alarm system identification.

Default setting: x=0

Notes:

The setting can only be done by SMS.

The events from the GC-61 (e.g. triggering its own input), are

transferred with an ID number according to the PG3p zzzz settings.

2.7. Format setting

This sequence is used to select the communication format:

PG4p x

where: p 1=ARC1, 2=ARC2

x is the protocol type – see table

Default setting: Contact ID for both ARC’s

Protocol Type x

Contact ID DTMF 0

Jablotron SMS SMS type 1

Jablotron GPRS GPRS type 2

2.8. Disabling ARC communication

If you need to temporarily disable all ARC reporting, you can do this,

while retaining your settings:

PG5p 1 all reports to ARC p enabled

PG5p 0 all reports to ARC p disabled

where: p 1=ARC1, 2=ARC2

Default setting: all ARC reports disabled.

2.9. ARC 2 as a back-up for ARC1

ARC 2 can serve as an optional back-up for ARC data transfer if

ARC1data transfer fails. When the first event is transferred to the back-

up monitoring station (ARC2) a “tel. line #1 communication fault“ event

will be reported.

PG62 0 ARC1 and ARC2 are two independent stations

PG62 1 ARC 2 works as a transfer back-up

When 081 is selected, the ARC 2 settings are used only if ARC 1

transfer fails .

Default setting: two independent ARC’s.

2.10. ARC re-dialling interval setting

If the dialler is activated it attempts to make a connection (alternating

between the primary and the back-up telephone number). If it is not

possible to make a connection, a dialling pause is initiated. After this

interval the dialler will re-attempt to make a connection. The interval

can be set in the following way:

PG7p t

where: p 1 = ARC1, 2 = ARC2

t is the pause duration x 5 minutes (i.e.1 = 5 minutes,

2 = 10 min,..., 9 = 45 minutes etc)

Default setting: 5 minutes for both ARCs

2.11. Interval of periodic test

Periodic tests are sent by the GC-61. These events do not depend

on a connected control panel. The following sequence sets the time

interval between periodic test messages:

PG8p hh:mm

where: p 1 = ARC1, 2 = ARC2

hh is hours

mm is minutes

Default setting: the periodic test is not sent – 00:00 is set

2.12. INP input CID code setting

When the INP input is used for transmission to an ARC, it is

necessary to set CID code for the required event. Enter the following

sequence:

PG91 xxxyyzzz

where: xxx is the event (e.g. alarm – 130, tamper – 137,

arm/disarm – 401 etc.)

yy is the number of the subsystem

zzz is the number of event source

Example: if you enter PG91 13001123, then on activation of the INP

input, the report –“ alarm to subsystem 01, event source 123” will be

sent to the ARC.

Default setting: no report is transferred.

2.13. Phone number prefix setting.

In some countries it is necessary to use “00” instead of the “+”

character as a prefix at the beginning of a phone number to be able to

send SMS message. If required, enter this sequence:

PG92 xx

Where: xx is the prefix which will be used instead of “+”

Enter PG92 to reset to the default setting.

Default setting: “+”.

2.14. Reset to the default setting

When the SMS “reset” is sent to the GC-61, the factory default

setting will be restored. A hardware reset can also be performed as

follows:

Switch off the power supply, connect the two middle pins of the K1

connector and restore the power supply. The hardware reset is

indicated by fast LED flashing.

2.15. Reset – GSM module

When the command gsm is sent to the GSM module it will

disconnect from and then reconnect to the GSM network. This function

is useful when it is necessary to switch the mobile device off and on

(e.g. when the SIM card has been unblocked by the mobile operator).

2.16. Appliance remote control by SMS (AUXON,

AUXOFF)

These commands can be used to control the AUX output (e.g. switch

a telephone line to the control panel). The switching event is sent to an

ARC. The AUX is also switched on if a GSM network is not available

for 15 minutes.

To switch on the AUX output, send the SMS text: AUXON

To switch off the AUX output, send the SMS text: AUXOFF

Produkt Specifikationer

Mærke:	Jablotron
Kategori:	Sikkerhed
Model:	GC-61

Har du brug for hjælp?

Hvis du har brug for hjælp til Jablotron GC-61 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sikkerhed Jablotron Manualer

Jablotron EYE-02 Manual

22 August 2024

Jablotron JA-60G Manual

22 August 2024

Jablotron JA-60B Manual

21 August 2024

Jablotron JA-63E Manual

21 August 2024

Jablotron JA-80D Manual

21 August 2024

Jablotron JA-50S Manual

21 August 2024

Jablotron JA-63F Manual

21 August 2024

Jablotron GBS-200 Manual

19 August 2024

Jablotron JA-63F wireless keypad Manual

17 August 2024

Jablotron CA-322 Accent Manual

17 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech SHATTERPRO 3 Manual

15 Januar 2025

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025

Eminent EM6511 Manual

15 Januar 2025

Ranex RX2567-Z Manual

11 Januar 2025

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024

Provision-ISR NVR2-4100P Manual

23 September 2024

Gira 0342 Manual

23 September 2024

Unitron Smart Alert Systeem Manual

23 September 2024

Netatmo Welcome Manual

21 September 2024

NetworX NX-408 Manual

20 September 2024