Jablotron JA-80D Manual

Jablotron Sikkerhed JA-80D

Læs gratis den danske manual til Jablotron JA-80D (1 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Jablotron JA-80D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The JA-80D universal transmitter 1 / 1 MHQ52802

The JA-80D universal transmitter

The JA-80D is a component of Jablotron’s Oasis 80 alarm system. It is

designed to indicate device status via wireless transmissions. Such a

device is typically a detector, but other devices with an ON/OFF

switching output terminal (whether NC or NO) are also applicable.

Among other uses, status transmission allows the control panel

communicator to report device faults. The JA-80D transmitter is

battery-powered.

Installation

Installation shall only be undertaken by technicians holding a

certificate issued by an authorized distributor. The transmitter should

be installed vertically. Avoid locating it directly on a metal frame as

metal influences the functioning of the magnetic sensor and radio

communication.

• Open the transmitter cover by pressing the tab in.

• Get an appropriate cable ready for the connection of a desired

device and test the device’s output terminal for its NO/NC

switching logic.

• Configure the transmitter function via the DIP switches (No. 1 and

2, see below).

• Route the cable and screw the cover onto the chosen location.

• Enroll the transmitter to the control panel (to a receiver) – follow

the control panel or receiver manual. The basics of enrollment are:

o Enter enrollment mode on the control panel by keying in “1” in

Service mode.

o Install a battery into the device to activate enrollment.

o Exit enrollment mode by pressing #.

• Wire the cable to the terminals and test the function.

To enroll the transmitter after having already connected a battery, first

disconnect the battery, and press and release the tamper sensor to

discharge any remaining charge to ready the device for enrollment.

DIP switches

Tamper

sensor

Terminals

Reaction

Input logic

NC ( )

normal

INSTANT

DELAY

LITHIUM

3. V AA6

NO ( )

inverted

• NO/NC – determines which of the Closed/Open input states is

interpreted as OFF. By default (corresponding to security industry

standards) the input is NC (Normally Closed). If a pulse reaction

is requested – so that only activations should be signalled – keep

the tamper switch pressed during battery installation.

• INSTANT/DELAY – selects what the natural reaction of the

control panel will be to an activation signal from the device

connected to the IN terminal. INSTANT = instant alarm, DELAY

= entrance delay starts – both require the system to be in a set

(armed) condition. The INSTANT/DELAY option is only

applicable for use with an OASiS control panel with a natural

reaction assigned to its address. The switch has no effect when

used with a UC-8x or AC-8x receiver.

• Whenever the detector (device) cover is opened, a tamper signal

is sent.

• Tamper indication also occurs on every TMP input

activation. If this function is not desired, the TMP and GND

terminals must be wired together.

Overflow alert detector – a wiring example (NO contact)

TMP

GND

Overflow

detector

Example of NO contact wiring

Note: The wiring loop must not exceed 3 meters in length (this

means a limit of 6 m in the total wire length).

Testing the detector

15 minutes after closing the detector cover, the LED indicates

detector triggering. The strength and quality of the detector‘s radio

signals can be measured by the control panel in Service mode.

Detector battery replacement

The system monitors its battery voltage and if too low, a transmission

is sent to the control panel (receiver) to inform the installer or user. The

detector continues to function and shows each triggering of the

detector with a flash of its LED. Battery replacement should not be

delayed by more than two weeks. This should be done by a qualified

technician with the control panel in Service mode. We recommend

testing the detector immediately after its battery has been replaced.

Inserting a battery with a low voltage results in the LED indicator

flashing for approx. 1 minute. Subsequently, the detector will switch

to normal operation including low battery indication of the kind

described above.

Expired batteries should not be thrown into the garbage, but disposed

of according to local regulations.

Removing the detector from the system

If a detector is removed, the control panel announces the removal.

The detector has to be deleted in the control panel before intentional

removal.

Specifications

Voltage Lithium battery type LS(T)14500 (3.6V AA)

Typical battery lifetime

approx. 3 years for 20 daily activations maximum

INP/TMP wiring loop length < 3m in one direction

(< 6m in total)

Communication band 868 MHz, Oasis protocol

Communication range approx. 300m (open area)

Dimensions 110 x 31 x 26 mm

Operational environment according to EN 50131-1 II. Indoor general

Operational temperature range -10 to +40 °C

EN 50131-1,CLC/TS 50131-2-6, EN 50131-5-3 classification: grade 2

Complies with

ETSI EN 300220, EN50130-4, EN55022, and EN 60950-1

Can be operated according to ERC REC 70-03

Jablotron Ltd. hereby declares that the JA-80D is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC. The original of

the conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Note: Dispose of batteries safely depending on battery type

and local regulations. Although this product does not contain

any harmful materials we suggest you return the product to

the dealer or directly to the manufacturer after use.

: www.

jab

Tel.: +420 483 559 999

fax: +420 483 559 993

Pod

Skalkou

466 01 Jablonec nad Nisou

Czech Republic

Produkt Specifikationer

Mærke:	Jablotron
Kategori:	Sikkerhed
Model:	JA-80D

Har du brug for hjælp?

Hvis du har brug for hjælp til Jablotron JA-80D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sikkerhed Jablotron Manualer

Jablotron EYE-02 Manual

22 August 2024

Jablotron JA-60G Manual

22 August 2024

Jablotron JA-60B Manual

21 August 2024

Jablotron JA-63E Manual

21 August 2024

Jablotron JA-80D Manual

21 August 2024

Jablotron JA-50S Manual

21 August 2024

Jablotron JA-63F Manual

21 August 2024

Jablotron GBS-200 Manual

19 August 2024

Jablotron JA-63F wireless keypad Manual

17 August 2024

Jablotron CA-322 Accent Manual

17 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech SHATTERPRO 3 Manual

15 Januar 2025

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025

Eminent EM6511 Manual

15 Januar 2025

Ranex RX2567-Z Manual

11 Januar 2025

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024

Provision-ISR NVR2-4100P Manual

23 September 2024

Gira 0342 Manual

23 September 2024

Unitron Smart Alert Systeem Manual

23 September 2024

Netatmo Welcome Manual

21 September 2024

NetworX NX-408 Manual

20 September 2024