Jablotron JA-60B Manual

Jablotron Sikkerhed JA-60B

Læs gratis den danske manual til Jablotron JA-60B (2 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Jablotron JA-60B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Bezdrátový akustický detektor rozbití skla JA-60B 2/2 MEY51012

JA-60B WIRELESS GLASS BREAK DETECTOR

The JA-60B is a modern wireless glass break detector that provides

easy and reliable protection against robbery. It ensures extremely high

reliability and false alarm immunity. One sensor covers an entire room,

regardless of the number of windows. A dual technology detection method

(air pressure and sound analysis) is combined with digital processing to

guarantee high sensitivity to the breaking of glass.

A special testing mode enables simple adjustments to the detector.

Regular self testing is performed and the final result is transmitted to a

control panel. Digital hopping code radio communication guarantees highly

secure data transmission. The detector is also protected against

tampering.

Specification:

Detection method acoustic signal analysis

Power voltage 3 V (2x alkaline AAA batteries)

Battery life time typically 1 year

Detection range max. 9 m

Working freguency 433,92 MHz

Communication distance (open air) up to 100 m

Complies with EN 50131-1 grade 2

Environmental class II indoor general, -10 to +40°C

Can be operated according to ERC REC 70-03

Contents of JA-60B set: detector, 2 dowels, 2 screws, 2x AAA batteries

Hereby, Jablotron Ltd., declares that this JA-60B is in compliance

with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Installation

The JA-60B can detect the breaking of glass that is part of the

peripheral walls of the protected area. The glass must be fixed in a

frame and its minimum size must be 0.6 x 0.6 m. The distance

between the detector and the glass should not exceed 9 meters. The

JA-60B can be mounted on a wall or a ceiling. The unit must have an

unobstructed view of the protected glass (in the case of heavy curtains,

mount the unit on the widow frame behind the curtains). The detector

should not be installed close to any metal surfaces or other objects

obstructing radio signal transmission.

Installation procedure:

• Open the detector cover by pressing the internal tab.

• Attach the detector to the wall or ceiling using the 2 provided screws.

• The antenna should be vertical (pointing up or down).

• The INS/DEL jumper should be closed if you want the system to react

immediately. Opening the jumper will select for a delayed reaction.

• Do not install JA-60B closer than 0.5 m to other wireless detectors.

Enrollment of the detector to the system

• Study the installation manual of the receiver unit (control panel) to

learn how to enter the enrolling mode to enroll the detector.

• Install the two provided AAA batteries into the detector (polarity is

marked in the detector) and leave it uncovered.

• The detector will generate an enrollment signal after the batteries

are installed.

• The detector needs about 60 sec. to be ready to recognize glass

breaking after battery installation. This period is indicated with

steady light of the red LED.

Detector testing

• Attach the detector’s cover. From this moment the detector will be in

a testing mode for 5 minutes and each triggering will be indicated by

the detector’s LED.

• Strike carefully the protected glass with a cushioned instrument.

• If the red LED on the detector responds with a short flash, then the

low frequency sensitivity is suitable.

• Test the detector’s reaction on all protected glass surfaces.

• If the sensitivity is too low, adjust it with the variable resistor

(clockwise direction for higher sensitivity and conversely)

• For complete function testing, you can use a suitable glass break

simulator (recommended model GBT-201)

• When detecting breaking glass the red LED will light for a longer

period and an alarm message will be transmitted to the receiver.

• Five minutes after the cover was attached, the detector will

automatically enter the normal mode and its LED indicator will be

switched off (battery energy saving function). Open and close the

detector‘s cover to reset the testing mode for an additional 5 minutes

if needed.

Notes:

Do not set the sensitivity too high. The device should detect only

intensive strikes.

For maximum protection against false alarms, try to activate any device

in the area that may automatically cycle such as pumps, generators,

heating/air-conditioning, etc. If the cycling device triggers an alarm, mount

the unit in a different location.

Battery testing and replacement

The detector automatically checks the condition of its batteries. If it is

necessary to replace the batteries, the detector will inform the system.

While in a low battery mode, the detector works as normal, but each

low frequency activation is indicated with a flash of the LED. If a low

battery is indicated, it should be replaced as soon as possible (in a

week).

Before the batteries are replaced, the receiver (control panel) must

be put into the mode which allows for the opening of the detector (User

or Programming mode).

Use only high quality alkaline AAA batteries for replacement. After

you remove old batteries, wait 30 sec. before you install new ones.

Possible problems

No reaction after inserting batteries – remove the batteries and check

if they were inserted with the correct polarity, check their voltage

False alarms – some devices can generate frequencies that are similar

to the spectrum of breaking glass. (See paragraph Detector testing)

False alarms occurs when entering the premises - certain noises

(e.g. squeaking doors) can activate the detector – open the jumper

inside to set the JA-60B for delayed reaction

Unstable radio communication – ensure that there isn’t any metal

barrier between the detector and the receiver (control panel) and that the

detector’s antenna is positioned in parallel to the control panel’s antenna

(but they should not be in one line).

Note: Dispose of batteries safely depending on the type of the batteries

and local regulation. Although this product does not contain any harmful

materials we suggest you to return the product to the dealer or directly to

the producer after usage.

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 483 559 993

Pod Skalkou 3 3

466 01 Jablonec nad Nisou

Czech Republic

Bezdrátový akustický detektor rozbití skla JA-60B 2/2 MEY51012

Produkt Specifikationer

Mærke:	Jablotron
Kategori:	Sikkerhed
Model:	JA-60B

Har du brug for hjælp?

Hvis du har brug for hjælp til Jablotron JA-60B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sikkerhed Jablotron Manualer

Jablotron EYE-02 Manual

22 August 2024

Jablotron JA-60G Manual

22 August 2024

Jablotron JA-60B Manual

21 August 2024

Jablotron JA-63E Manual

21 August 2024

Jablotron JA-80D Manual

21 August 2024

Jablotron JA-50S Manual

21 August 2024

Jablotron JA-63F Manual

21 August 2024

Jablotron GBS-200 Manual

19 August 2024

Jablotron JA-63F wireless keypad Manual

17 August 2024

Jablotron CA-322 Accent Manual

17 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech SHATTERPRO 3 Manual

15 Januar 2025

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025

Eminent EM6511 Manual

15 Januar 2025

Ranex RX2567-Z Manual

11 Januar 2025

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024

Provision-ISR NVR2-4100P Manual

23 September 2024

Gira 0342 Manual

23 September 2024

Unitron Smart Alert Systeem Manual

23 September 2024

Netatmo Welcome Manual

21 September 2024

NetworX NX-408 Manual

20 September 2024