JL Audio M-LCB-C-W Manual

JL Audio Ikke kategoriseret M-LCB-C-W

Læs gratis den danske manual til JL Audio M-LCB-C-W (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om JL Audio M-LCB-C-W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Instructions for

M-LCA-C-W

M-LCB-C-W

L E D L I G H T C A P

FOR ETXv e3 & V X™ ENCLOSED SPE AKER SYSTEMS

NOTE: The M-LCA-C-W Light Cap and M880-ETXv3-SG-WH Enclosed Speaker System are

used in this manual for illustrative purposes only. The installation steps are the same for

all ETXv3 and VeX™ Enclosed Speaker Systems and all LED Light Caps.

LIMITED WARRANTY  MARINE PRODUCTS USA

JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the

original date of purchase.

This warranty is not transferable and applies onl y to the original purchaser from an authorized JLAUDIO dealer. Should service

be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),

repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not

covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,

unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential dam ages

and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not

covered under warranty.

Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning

with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product

thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For Service Information in the U.S.A. please call

JL Audio Customer Service: (954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc

10369 North Commerce Pkwy.

Miramar, FL 33025, USA

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and n ot by JL Audio, Inc.

w w w . j l a u d i o . c o m

JL Audi o® and the JL Audi o logo are re gistere d trademar ks of JL Aud io, Inc. “Ahead of the Curve” and its resp ective logo is a trad emark of JL Au dio, Inc.

©2017 JLAud io, Inc. • For m ore detailed inform ation plea se visit us online at Due to ou r policy o f continuous produc t developm ent, all sp ecifications are su bject to change without notice. www.jlaudio.com.

Included Hardware: BOM ID Quantity Description

1 1 M10 Locknut Tool

2 2 M10 x 1.5 Nylon Insert Flange Locknut

3 2 LED Light Cap

4* 2 readed Stud

5* 2 O-Ring

- 2 150mA Fuse (not shown)

- 2 Fuse Holder (not shown)

- 2 Female Connector (not shown)

Note: Not all wires may be used in normal applications.

Wire Size Wire Color Use

16 AWG Red/Stripe Speaker Positive (+)

Black/Stripe Speaker Negative (–)

20 AWG

Red LED Light Cap Positive (+)

Green LED Light Cap Negative (-)

Blue Speaker LED Positive (+)

Yellow Speaker LED Negative (–)

* Pre-installed on LED Cap

(hardware pictured for one)

Enclosed Speaker System Wiring:

Wire Size Wire Color Use

18 AWG Red LED Positive (+)

Black LED Negative (–)

LED Light Cap Wiring:

Printed in U.S.A. • 112017

Remove the six #8 x 1-1/4” Pan Head Screws and six #8

Flat Washers that secure the speaker to the enclosure.

Connect the LED wires from the LED Light Cap to the

LED wires entering the enclosure. Refer to the wiring

charts on the opposite page for details. DO NOT install

the fuse holders inside the enclosure.

Using the exterior angles of the JL Audio logo as a

guide, mark the center of the rear aluminum logo cap,

as shown. Using a punch tool, make an indent in the

aluminum logo cap on the center mark.

Slide the M10 Locknut Tool over the LED wires and onto

the M10 x 1.5 Nylon Insert Flange Locknut.

Disconnect the speaker wiring and speaker LED

wiring (if equipped), and remove the speaker from the

enclosure.

Slide an M10 x 1.5 Nylon Insert Flange Locknut over the

LED wiring, and hand-tighten onto the readed Stud.

Using a 7/16” drill bit, carefully drill through the center of

the rear aluminum logo cap, into the enclosure. File any

sharp edges.

Reconnect the speaker wiring, and reinstall the speaker

using the six #8 x 1-1/4” Pan Head Screws and six #8

Flat Washers.

Rotate the LED Light Cap to the desired angle. Using the

M10 Locknut Tool, fully tighten the M10 x 1.5 Nylon Insert

Flange Locknut until the O-ring is fully compressed and not

visible to ensure the unit is properly sealed. Remove the M10

Locknut Tool from the enclosure.

Pass the LED wires and readed Stud on the back of the

LED Light Cap through the drilled hole, and position the

cap ush against the back of the enclosure.

• For marine installations, do not connect the LED lights

to the vessel’s navigational lighting circuits.

• For short-circuit protection, install a supplied fusehold-

er onto EACH LED Light Cap’s RED (+12V) LED power

connection lead.

• Connect all RED (+12V) leads together (parallel) and

connect to a switched +12V supply. Connect all

GREEN (GND) leads together and connect to a

negative ground or to the NEGATIVE battery post.

• We recommend activating the LEDs thru a lighting

circuit that supplies +12V via an existing switch. If an

existing switched circuit is not available, you may install

a dedicated toggle/rocker style switch that will supply

positive (+12V) power. Fuse this connection according

to how many LED circuits you have (LED circuits x

150 mA).

[ D]GN

LED

[+12V]

Blue

Yellow

Blue

Yellow

Red

Black

Red

Black

LED

Fuse

[ D]GN

[+12V]

Blue

Yellow

Red

Black

Blue

Yellow

Red

Black

Blue

Yellow

Red

Black

Blue

Yellow

Red

Black

LED

Fuse

Example: One pair of LED circuits

connected in parallel.

Example: Two pairs of LED circuits

connected in parallel.

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Ikke kategoriseret
Model:	M-LCB-C-W

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio M-LCB-C-W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret JL Audio Manualer

JL Audio Stealthbox SBX-T-TCMAX3G/12TW3 Manual

10 Marts 2025

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Manual

30 December 2025

JL Audio Stealthbox SB-F-ESCP/10W1v3 Manual

30 December 2025

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/BK Manual

8 December 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Manual

4 Oktober 2024

JL Audio MBT-RX Manual

3 Oktober 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Manual

29 September 2024

JL Audio MBT-CRXv2 Manual

10 September 2024

JL Audio MBT-RXv2 Manual

4 September 2024

JL Audio MBT-CRXv3 Manual

4 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025