JL Audio M-SWMCPv3-1.315 Manual

JL Audio Højttaler M-SWMCPv3-1.315

Læs gratis den danske manual til JL Audio M-SWMCPv3-1.315 (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om JL Audio M-SWMCPv3-1.315, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Instructions for

M-SWMCPv3-1.315 • M-SWMCPv3-1.660 • M-SWMCPv3-1.900

M-SWMCPv3-2.000 • M-SWMCPv3-2.250

M-SWMCPv3-2.375 • M-SWMCPv3-2.500

P I PE M O UN T I N G F I X T U R E S ( S W I V EL)

FOR ETXv3 ENCLOSED SPEAKER SYSTEMS

LIMITED WARRANTY  MARINE PRODUCTS USA

JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the

original date of purchase.

This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service

be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),

repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not

covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,

unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages

and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not

covered under warranty.

Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning

with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product

thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For Service Information in the U.S.A. please call

JL Audio Customer Service: (954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc

10369 North Commerce Pkwy.

Miramar, FL 33025, USA

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

w w w . j l a u d i o . c o m

JL Audio® and the JL Audio logo are regist ered tr adem arks of JL Audio, Inc. “Ahead of the Cu rve” and its respe ctive logo is a t rademark of JL Audio, In c.

©2014 JLAudio, Inc. • For more detailed inf ormation please visit us onl ine at Due to our policy of continu ous product development, all specifications are subject to change without notice. www.jlaudio.com.

SKU# 011429

Printed in U.S.A. • 040815

For best adhesion, it is recommended to clean the inside

of the aluminum cap with acetone (not included), prior

to attaching it to the speaker enclosure. Apply a circular

bead of silicone adhesive (included) to the inside of the

aluminum logo cap, about 1/2-inch (13 mm) from the

outer edge.

Align the aluminum logo cap to the desired angle of

rotation, and press it onto the back of the enclosure.

Apply masking tape (not included) to hold the cap in

place until the silicone cures (at least 24 hours).

Remove adhesive backing and install the JL Audio logo

badge (Sport Grille Models Only).

If a dierent speaker angle is desired, remove the speaker

mounting screws and washers.

Rotate the enclosure to the desired angle, install the

5/16 - 18 x 1/2” set screw into the base of the xture, and

fully tighten.

Rotate the speaker to the desired angle. Reinstall the

speaker and speaker mounting screws and washers.

Hand-tighten the screws in a criss-cross pattern.

Have a helper support the enclosure during this step.

Use the supplied butt connectors to connect the red (+)

and black (-) speaker cable exiting the ETXv3 enclosure

to the speaker cable exiting the pipe. e green and white

wires will not be used in this application.

Adjust the angle of the xture until level, mark the

location for the speaker cable hole. Remove the xture

assembly, and drill a 1/2” hole on the mark.

Align the two upper halves of the xture around the pipe.

Hand-tighten four 1/4 - 20 x 1-1/4” machine screws with

1/4” lock washers into the xture. DO NOT TIGHTEN

FULLY AT THIS POINT.

Compress the base and two upper halves of the xture

together while pushing the fork out through the small

pin holes on the opposite side. Flip the fork, and

reinstall, along with the two #8 - 32 x 3/8” machine

screws and lock washers.

Remove the four 1/4 - 20 x 1-1/4” machine screws and

1/4” lock washers to separate the two upper halves of

the xture. Pass the speaker cable exiting the enclosure

through the opening on the underside of the xture.

Slide the excess speaker cable and the butt connectors

into the opening in the pipe as you raise the enclosure to

ush the xture to the pipe.

In applications that require the logo to be inverted,

remove the two #8 -32 x 3/8” machine screws and lock

washers.

For applications where the cable cannot be routed

through the pipe, the cable can be passed through one of

the openings on the side of the xture.

Remove one of the 1/4 - 20 x 1-1/4” machine screws

and 1/4” lock washers at a time. Apply Loctite® red

thread-locking compound (included), reinstall, and fully

tighten. Repeat the same process for the other three

screws. (Continued on reverse.)

Determine the speaker mounting location, and

temporarily secure the xture around the pipe by hand

tightening the four 1/4 - 20 x 1-1/4” machine screws and

1/4” lock washers.

Apply Loctite® red thread-locking compound

(included) to two 5/16” - 18 x 1-1/4” machine screws

(included), thread them into the base of the xture, and

push down on the xture to ensure no gap while fully

tightening.

Be sure the indicated stopping points are on opposite

sides of the xture as shown. e enclosure can rotate

up to 205.5 degrees in the clockwise direction, and 128.5

degrees in the counter-clockwise direction.

128.5 205.5

IMPORTANT: Swivel mounting xtures should only be

attached to horizontal pipes. ETXv3 enclosures should

only be mounted directly above (12 O’clock position) or

directly below (6 O’clock position) a horizontal pipe.

NOTE: The M-SWMCPv3-2.000 fixture and

M770-ETXv3-SG-WH Enclosed Speaker

System are used in this manual for illustrative

purposes only. The fixture installation steps

are the same for all ETXv3 Enclosed Speaker

Systems and all M-SWMCPv3 Swivel-Mount

Fixtures listed on front cover.

WARNING: Do not mount enclosures to a horizontal

pipe in any position other than directly above or directly

below.

WARNING: Never attach swivel mounting xtures to

vertical or angled pipes.

IMPORTANT WARNING

WARNING

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Højttaler
Model:	M-SWMCPv3-1.315

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio M-SWMCPv3-1.315 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler JL Audio Manualer

JL Audio M6-103EWS-Gw-C-3Gw Manual

27 Juli 2025

JL Audio C1-650se Manual

27 Juli 2025

JL Audio M3 Manual

3 April 2025

JL Audio C6-275cm Manual

7 Februar 2025

JL Audio C2-650 Manual

16 November 2024

JL Audio C1-690tx Manual

7 Oktober 2024

JL Audio M3-770X Manual

16 September 2024

JL Audio CF-275mt Manual

1 September 2024

JL Audio C6-100ct Manual

1 September 2024

JL Audio C6-650 Manual

1 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Muse M-968 BTY Manual

1 August 2025

Grundig Portable 360 Manual

1 August 2025

Grundig Band 360 Manual

1 August 2025

Grundig GBT Connect 360 Manual

1 August 2025

Muse M-968 BTR Manual

31 Juli 2025

JLab Epic Party Manual

31 Juli 2025

JVC XS-E423 Manual

30 Juli 2025

SoundTube RF31-EZ-T Manual

30 Juli 2025

Valcom VIP-480AL-W-SA Manual

30 Juli 2025

Rockustics StoneHenge II-S/T Manual

30 Juli 2025