JL Audio MLC-RW Manual

JL Audio Ikke kategoriseret MLC-RW

Læs gratis den danske manual til JL Audio MLC-RW (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 61 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 31 anmeldelser. Har du et spørgsmål om JL Audio MLC-RW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Thank you for purchasing a JL Audio Marine Lighting

Controller for your sound system.

This product has been designed and manufactured to exacting

standards in order to deliver years of enjoyment. For maximum

performance, we highly recommend that you have your MLC-RW

installed by an authorized JL Audio dealer. Your authorized dealer has

the training, expertise and installation equipment to ensure optimum

performance from this product. Due to the complexity of modern

electrical systems, we do not recommend self-installation unless you

have extensive experience in automotive and marine electrical systems.

Should you decide to install this product yourself, please take the time to

read this manual thoroughly to familiarize yourself with its installation

requirements and setup procedures.

If you have any questions regarding the instructions in this manual or

any aspect of the product’s operation, please contact your authorized

JL Audio dealer for assistance. If you need further assistance, please submit

a request to the JL Audio Technical Support Department at

www.jlaudio.com/support or call (954) 443–1100 during business hours.

OWNER’S MANUAL

Marine Lighting Controller

MLC-RW

2 | JL Audio - MLC-RW Owner’s Manual

FCC Compliance Statement

is equipment has been tested and found

to comply with the limits of Part 15 of the

FCC Rules. ese limits are designed to

provide reasonable protection against harmful

interference in a residential installation. is

equipment generates, uses and can radiate

radio frequency energy and, if not installed in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If

this equipment does cause harmful interference

to radio or television reception, the user is

encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase separation between the equipment

and the receiver.

- Connect the equipment to an outlet on a

circuit dierent from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV

technician for help.

Any changes or modications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate

this equipment.

Connections

Safety Considerations

• Install the controller module in a dry, well-

ventilated location that does not interfere with

factory-installed systems. Do not install where

it will be directly exposed to the elements.

• Do not mount this product in an engine

compartment or areas of extreme heat.

Areas exposed to a heater or hot air should

also be avoided.

• Securely mount this product so that it does not

come loose in the event of a collision, sudden

jolt or as a result of repeated vibrations during

normal use.

• Check before drilling to make sure that you will

not be drilling into an exterior panel/hull, fuel

tank, gas/brake line, wiring harness or other

vital system.

• Do not run system wiring outside or underneath

the vehicle/vessel. is is an extremely

dangerous practice, which can result in severe

damage/injury.

• Protect all system wires from sharp edges and

wear by carefully routing them, tying them

down and using grommets and loom where

appropriate. Secure all wiring using cable ties or

wire clamps, as needed.

Panel-Mounting Rotary Encoder

ROTAR Y EN CODER

POWER CONN ECT IONS

+12 VD C* (Ye ll ow)

GRO UN D (Black)

I LLUMI N AT IO N

+Main RGB (W hit e)

–R ed RGB (Red)

–Gree n RGB (Green)

–Blu e RGB (Blue)

Under-Dashboard Mounting Rotary Encoder

Gasket

Threaded Collar

Mounting Bracket

1" Mounting Hole

Gasket

Threaded Collar

* Install a fuse at the +12VDC Power Wire

(Yellow) connection point that is appropriate for

the total current draw of all LED circuits.

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Ikke kategoriseret
Model:	MLC-RW

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio MLC-RW stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret JL Audio Manualer

JL Audio Stealthbox SBX-T-TCMAX3G/12TW3 Manual

10 Marts 2025

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Manual

30 December 2025

JL Audio Stealthbox SB-F-ESCP/10W1v3 Manual

30 December 2025

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/BK Manual

8 December 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Manual

4 Oktober 2024

JL Audio MBT-RX Manual

3 Oktober 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Manual

29 September 2024

JL Audio MBT-CRXv2 Manual

10 September 2024

JL Audio MBT-RXv2 Manual

4 September 2024

JL Audio MBT-CRXv3 Manual

4 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Synology CMA-01 Manual

1 August 2025

Synology RKS-02 Manual

1 August 2025

Navman MiVue 765 SAFETY Manual

1 August 2025

Navman MY75T Manual

1 August 2025

Exquisit AIRFRY 3010 Manual

1 August 2025

Navman MiVue 155 SAFETY Manual

1 August 2025

Navman MiVue 698 Manual

1 August 2025

Newland FM550 Manual

1 August 2025

Tripp Lite SRIN4181810 Manual

1 August 2025

Navman MyTruck III Manual

1 August 2025