JL Audio Stealthbox SB-F-FLX/10W3v3 Manual

JL Audio Ikke kategoriseret Stealthbox SB-F-FLX/10W3v3

Læs gratis den danske manual til JL Audio Stealthbox SB-F-FLX/10W3v3 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19 anmeldelser. Har du et spørgsmål om JL Audio Stealthbox SB-F-FLX/10W3v3, eller vil du spørge andre brugere om produktet?

Side 1/3
I N S T A L L A T I O N G U I D E
for the
SB-F-FLX/10W3v3
SKU#94451
2009 & Up Ford Flex
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-
specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation
professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle
properly. Also, keep in mind that your warranty coverage extends to 2 years if your system is installed or approved by your
authorized JL Audio dealer. If you prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Empty out the back of the vehicle.
Continued on Next Page
S T E P 2
Remove the passengers side rear door sill.
S T E P 3
Remove the false floor and, the tailgate, and door sill.
SB-F-FLX-10W3v3 INSTR_SKU# 011293
INSTALLATION
D I F F I C U L T Y :
35
OUT
OF
ESTIMATED TIME:
2-3 HOURS
Continued on Next Page
SB-F-FLX-10W3v3 INSTR_SKU# 011293
S T E P 7
Using a die grinder (or a Dremel® type tool), grind off all of
the plastic welds as shown.
***CAUTION***
Always follow proper safety techniques when using
power tools as described by the tool manufacturer.
S T E P 6
The factory subwoofer grille (as shown) needs to be
removed. This process will be done from the back side of
the panel.
S T E P 5
Remove the OEM subwoofer/amplifier as shown. Run the
wire for the Stealthbox® to this general location (indicated by
arrow), as the Stealthbox® will be mounted here. Leave extra
wire so that you can secure it as desired once the installation
is finished.
S T E P 4
Remove the interior plastic trim panel. You can leave the
sections of the panel that the seat belts go through as
shown.
Page 2 • JL Audio, Inc 2016
S T E P 9
Looking at the panel from the front, trim all of the edges of
the opening leaving a 3/8” flange inside the recess at the top,
and a 1” flange inside the recess at the sides and bottom.
S T E P 1 1
Remove the woofer and stuffing from the Stealthbox, slide
the Stealthbox® into position, mark the two mounting holes
as shown, and remove the enclosure.
S T E P 1 0
Re-install the interior panel along with all of the previously
removed panels. Make sure that you can access the previ-
ously run wire for the Stealthbox®.
S T E P 8
This is the back of the grille completely removed showing all
of the welds that needed to be removed.
3/8”
1”


Produkt Specifikationer

Mærke: JL Audio
Kategori: Ikke kategoriseret
Model: Stealthbox SB-F-FLX/10W3v3

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio Stealthbox SB-F-FLX/10W3v3 stil et spørgsmål nedenfor, og andre brugere vil svare dig