JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 Manual

JL Audio Ikke kategoriseret Stealthbox SB-F-SUPRCNSL/10W3v3

Læs gratis den danske manual til JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9 anmeldelser. Har du et spørgsmål om JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 1

for the

SB-F-SUPRCNSL/10W3v2

(‘98-Up Ford SuperDuty

250,350,450,550 & 650

‘00-Up Excursion)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

From inside the factory console,

using a 9/16” socket, remove the four bolts

that secure the console to the vehicle. ( Two

of these bolts will be used later to secure

the Stealthbox).

STEP 2:

Remove the console from the vehi-

cle.

STEP 3:

Remove the inside section of the

console. (This will not be reinstalled).

-Two screws are located under the front tray.

-Three screws attach the hinge.

-Three screws are located on each side of the

consoles shell (six total)

After this section is removed, the console shell

will be in two parts.

STEP 4:

Using a pair of pliers, from the inside

of the console shell. Remove the ridges locat-

ed toward the front of the console.

STEP 5:

Reassemble the front and rear parts

of the console shell using the supplied hard-

ware (4 #8 x 1/2” long screws, 4 washer and

4 nuts) as shown in the picture.

STEP 6:

Turn the console shell upside down.

Position the Stealthbox inside the shell,

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

STEP 7: Use the remaining mounting holes as a

drill guide.

Using a 1/8” drill bit and drill, drill a hole through

each of these guide holes, into the Stealthbox.

STEP 8: Install #8x 1/2” black pan-head screws

into the drilled holes.

➔ ➔

➔➔➔

STEP 10: Install #8 x 1/2” black pan-head screws

into the drilled holes.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 11: Using a 1/8” drill bit and drill. Drill two

holes at the hinge area using the outside holes only.

The center hole does not need to be drilled.

➔

STEP 12: Remove the screws installed in STEP 8

and STEP 10. Separate the console shell from the

Stealthbox.

STEP 13: Attach the OEM’s console lid to the

shell. Use one of the OEM’s screws and supplied

speed-clip to the center hole of the hinge.

STEP 9: Turn the console right-side-up with the

Stealthbox attached.

Using the holes on the top of the console shell as

guides, use a 1/8” drill bit and drill to drill holes

through each of these guide holes and into the

Stealthbox.

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 2

w w w . j l a u d i o . c o m

STEP 14: Place the Stealthbox in the vehicle. Using

a pair of OEM bolts, from STEP 1. Loosely secure

the rear foot bracket to the floor, do not tighten.

STEP 15: Remove the paper backing on the sup-

plied sheet wax squares.

With the Stealthbox in place, lift the front of the

Stealthbox and position both supplied sheet wax

squares onto the carpet and lined up with the front

foot bracket of the Stealthbox, lower the console

down.

STEP 16: Using one of the supplied 3/8”x1-1/2”

bolts, place the bolt through each hole of the front

foot bracket (one at a time). Press down on the bolt,

too leave impressions on the sheet wax squares.

STEP 17: Remove the two OEM bolts from STEP

14. Remove the Stealthbox from the vehicle.

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Ikke kategoriseret
Model:	Stealthbox SB-F-SUPRCNSL/10W3v3

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret JL Audio Manualer

JL Audio Stealthbox SBX-T-TCMAX3G/12TW3 Manual

10 Marts 2025

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Manual

30 December 2025

JL Audio Stealthbox SB-F-ESCP/10W1v3 Manual

30 December 2025

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/BK Manual

8 December 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Manual

4 Oktober 2024

JL Audio MBT-RX Manual

3 Oktober 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Manual

29 September 2024

JL Audio MBT-CRXv2 Manual

10 September 2024

JL Audio MBT-RXv2 Manual

4 September 2024

JL Audio MBT-CRXv3 Manual

4 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025