JL Audio Stealthbox SB-GM-EQNX/10W1v3 Manual

JL Audio Ikke kategoriseret Stealthbox SB-GM-EQNX/10W1v3

Læs gratis den danske manual til JL Audio Stealthbox SB-GM-EQNX/10W1v3 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 18 anmeldelser. Har du et spørgsmål om JL Audio Stealthbox SB-GM-EQNX/10W1v3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

I N S T A L L A T I O N G U I D E

for the

SB-GM-EQNX/10W1v3

SKU#94503

2010-2017 Chevrolet Equinox / GMC Terrain

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-

specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation

professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle

properly. Also, keep in mind that your warranty coverage extends to 2 years if your system is installed or approved by your

authorized JL Audio dealer. If you prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox ® be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

S T E P 1

Empty out the trunk of the vehicle so that you have a clean

area to work in.

Continued on Next Page

S T E P 2

Remove the trunk floor, as well as the rear sill panel, by

pulling up on the panel to release the clips.

S T E P 3

Lift up on the covers of each tie down hook to expose the

screws, and remove both screws and hooks.

SB-GM-EQNX/10W1v3/BK INSTR_SKU# 011318

INSTALLATION

D I F F I C U L T Y :

OUT

ESTIMATED TIME:

1 HOUR

Continued on Next Page

SB-GM-EQNX/10W1v3/BK INSTR_SKU# 011318

S T E P 7

Remove the two nuts holding the top of the enclosure in

place. Continue by removing the two nuts holding the

bottom of the enclosure in place. Disconnect the sub wiring

and remove the factory sub enclosure. Retain all four nuts

for the installation of the Stealthbox®.

S T E P 6

With the side panel out of the vehicle, the factory sub

enclosure can now be removed.

S T E P 5

Pictured is the weatherstripping removed from the side

panel. Starting here, begin unclipping the side panel and

continue toward the rear of the vehicle, and remove the

panel.

S T E P 4

Open the rear passenger side door. Pull up the

weatherstripping to allow access to the sill panel and side

panel. Remove the sill panel by pulling up on the panel to

release the clips.

Page 2 • JL Audio, Inc 2017

S T E P 9

Attach the two Upper Brackets to the Stealthbox® as shown

using a 1/4” Flat Washer, 1/4” Lock Washer, and 1/4 - 20 x

1” Bolt on each. Hand tighten to allow the brackets to be

adjusted later.

S T E P 1 1

Set the Stealthbox® in place by sliding the bottom of the

enclosure behind the Lower Brackets, and aligning the Upper

Brackets with the upper threaded studs. Hand tighten the

factory nuts on the threaded studs, and mark the location of

the Upper Brackets on the top of the enclosure. Firmly press

the enclosure toward the side of the vehicle, slide the Lower

Brackets into place, and mark the location of the Lower

Brackets on the floor of the vehicle.

Remove the Stealthbox®, align the Upper Brackets with the

marks on the enclosure, and firmly tighten. Align the Lower

Brackets with the marks in the vehicle, and firmly tighten.

S T E P 1 0

Attach the two Lower Brackets to the threaded studs using

the factory nuts, as shown. The smaller, angled bracket goes

on the stud closest to the rear of the vehicle. Hand tighten

to allow the brackets to be adjusted later.

S T E P 8

Pictured without the factory sub enclosure are the threaded

studs that held the bottom of the enclosure in place. It is not

necessary to remove the bracket for the foam floor support.

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Ikke kategoriseret
Model:	Stealthbox SB-GM-EQNX/10W1v3

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio Stealthbox SB-GM-EQNX/10W1v3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret JL Audio Manualer

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Manual

30 December 2025

JL Audio Stealthbox SB-F-ESCP/10W1v3 Manual

30 December 2025

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/BK Manual

8 December 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Manual

4 Oktober 2024

JL Audio MBT-RX Manual

3 Oktober 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Manual

29 September 2024

JL Audio MBT-CRXv2 Manual

10 September 2024

JL Audio MBT-RXv2 Manual

4 September 2024

JL Audio MBT-CRXv3 Manual

4 September 2024

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025