JL Audio Stealthbox SB-N-XTERR2/12W3v3 Manual

JL Audio Ikke kategoriseret Stealthbox SB-N-XTERR2/12W3v3

Læs gratis den danske manual til JL Audio Stealthbox SB-N-XTERR2/12W3v3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om JL Audio Stealthbox SB-N-XTERR2/12W3v3, eller vil du spørge andre brugere om produktet?

Side 1/2
INSTALLATION
D I F F I C U L T Y :
I N S T A L L A T I O N G U I D E
for the
SB-N-XTERR2/12W3v3
SKU# 94270
2005 - Up Nissan Xterra
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-
specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation
professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle
properly. Also, keep in mind that your warranty coverage extends to 1 year if your system is installed or approved by your
authorized JL Audio dealer. If you prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Apply the supplied wax square to the floor of the passenger
side cargo area. As shown in the picture.
Continued on Next Page
S T E P 2
Thread in the supplied socket cup set screw into the bottom
of the Stealthbox®, leaving 1/4-inch exposed.
Place the Stealthbox® into place and press down firmly.
S T E P 3
Remove the Stealthbox® from the mounting area. You will
notice an impression on the wax square.
With a 1/2-inch drill bit, drill at the impression. Drill through
the plastic and metal flooring.
Note: Before drilling, make sure that you are not going
to be drilling into any gas lines, brake lines, transmission
lines, electrical wiring, transfer case (4x4 vehicles) or
anything else that might cause a reduction in your
weekly pay. Always wear eye protection when drilling!
SB-N-XTERR2/12W3v3_INSTR_SKU#011219
25
OUT
OF
2-1/2-inch
5-inch
SB-N-XTERR2/12W3v3_INSTR_SKU#011219
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 6
From under the vehicle, place the supplied fender washer,
flat washer, lock washer and then hex nut onto to the
exposed socket cup set screw.
Secure the bolt assembly.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
S T E P 5
Place the Stealthbox® into the cargo area. Run speaker wire
from the amplifier location to the Stealthboand attach to
the terminal.
Back out the socket cup set screw, on the bottom of the
Stealthbox®. Leaving 1-1/2 inches exposed.
Place the Stealthbox® into the mounting area. Carefully
guiding the socket cup set screws through spacer and the
drilled hole.
S T E P 4
With a Unibit or 3/4-inch drill bit, enlarge the 1/2-inch hole in
the plastic flooring to 3/4-inch.
Place the 1/2-inch spacer into the 3/4-inch hole.
Page 3 • JL Audio, Inc 2016
All specifications are subject to change without notice. JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011219 - 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
w w w . j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y M I R A M A R , F L O R I D A 3 3 0 2 5 U S A
I N C L U D E D H A R D W A R E
(1) (1) 3” x 3” Wax Square 3/8 - 16 x 2-1/4” Socket Cup Set Screw
(1) 3/8” x 3/4” USS Flat Washer 3/8 - 16 Hex Nut(1)
(1) (1) 3/8” x 2” Fender Washer 3/8”(L) x 3/4”(OD) x 3/8”(ID) Spacer
(1) 3/8” Split Lock Washer
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 12W3v3-2
Nominal Impedance: 2 ohms
Continuous Power Handling: 500 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2. The diagram below shows
the recommended crossover settings for the XD300/1v2 when being used to power your Stealthbox ®.
The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6-1/2-inch / Front Doors
Fits JL Audio Models: TR650-CXi, C2-650x, C2-650, C3-650, C5-650x, C5-650, & ZR650-CSi
Rear Speaker Size / Location: 6-inch x 9-inch / Rear Panels
Fits JL Audio Models: TR690-TXi, C2-690tx


Produkt Specifikationer

Mærke: JL Audio
Kategori: Ikke kategoriseret
Model: Stealthbox SB-N-XTERR2/12W3v3

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio Stealthbox SB-N-XTERR2/12W3v3 stil et spørgsmål nedenfor, og andre brugere vil svare dig