J.P. Instruments EDM-830 Manual

J.P. Instruments Ikke kategoriseret EDM-830

Læs gratis den danske manual til J.P. Instruments EDM-830 (30 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om J.P. Instruments EDM-830, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/30
FAA APPROVED INSTALLATION MANUAL FOR THE EGT-701 Report 103
INSTALLING THE EGT-701 SCANNER® 1/20/09 Rev-E
THE OWNER OF THIS EDM-700/800/730/830
MUST KEEP THIS MANUAL
TABLE OF CONTENTS
Page
1) INSTALLING THE INDICATOR 3
2) EXHAUST GAS TEMPERATURE PROBE 3
3) TURBINE INLET TEMPERATURE PROBE 3
4) CYLINDER HEAD TEMPERATURE PROBE 4
5) SPARK PLUG GASKET CHT PROBE 4
6) INDUCTION AIR TEMPERATURE PROBE 4
7) OIL TEMPERATURE PROBE 5
8) OIL PRESSURE TRANSDUCER 7
9) OUTSIDE AIR TEMPERATURE PROBE 7
10) FUEL FLOW OPTION 8
11) WIRING 9
12) EGT AND CHT PROBE WIRING 9
13) ROUTING THE WIRING HARNESS 11
14) MANIFOLD PRESSURE INSTALLATION & CALIBRATION 12
15) RPM SENSOR INSTALLATION 13
16) OPERATING INSTRUCTIONS 14
17) INDICATOR INSTALLATION & RECORD 16
18) ENGINE OPERATION 16
19) LIMITATIONS & OPERATION 16
20) COMPONENT PARTS LIST FOR EGT PROBE 17
21) COMPONENT PARTS LIST FOR CHT PROBE 17
22) COMPONENT PARTS LIST FOR OIL PROBE 17
23) COMPONENT PARTS LIST FOR OAT PROBE 17
24) COMPONENT PARTS LIST FOR MANIFOLD PRESSURE 17
25) COMPONENT PARTS LIST FOR RPM 17
26) COMPONENT PARTS LIST FOR SINGLE ENGINE EGT/CHT 17
27) WEIGHT AND BALANCE DATA 17
28) CHANGING PROGRAMMED LIMITS 18
29) TROUBLE-SHOOTING 20
FIG-1 INSTRUMENT BEZEL TEMPLATE 22
FIG-2 EGT/CHT/TIT PROBE PLACEMENT 23
FIG-3 EGT PROBE INSTALLATION 24
FIG-6 EGT/CHT PICTORIAL LAYOUT 25
FIG-7 WIRING DIAGRAM DRAWING 300701 26
FIG-9 DRAWING 700744 FUEL FLOW WIRING 27
INSTRUCTIONS FOR CONTINUED AIRWORTHINESS (ICA) 28
J.P.INSTRUMENTS Inc.
PO BOX 7033
HUNTINGTON BEACH CA 92646
FAA APPROVED 1/20/09
Last printed 11/02/17
FAA APPROVED INSTALLATION MANUAL FOR THE EGT-701 Report 103
INSTALLING THE EGT-701 SCANNER® 1/20/09 Rev-E Page 2 of 30
READ THIS FIRST
The following notes apply to a new installation. Read this section before proceeding.
a) The JPI warranty found in the back of the pilots guide clearly states that JPI will replace defective parts
under warranty, but does NOT cover labor to remove or install any parts.
b) To prevent damage to the display it is essential that the four mounting screws not penetrate the
instrument more than 0.12 inches. Damage caused by screw penetration is not covered under
warranty.
c) You must be an FAA certified aircraft mechanic to install this instrument.
d) Check that any necessary FAA approvals (STC’s, etc) are available for the aircraft before beginning the
installation.
e) The most common cause of probe problems is poor terminal crimps. Crimp ring terminals with AMP part
45518 crimp tool or equivalent. Fold back the wire double before crimping terminals.
1/4" 1 1/2"
Fold back wire
double before
crimping terminals
2 1/4"
Thermocouple wire harness
red
yellow
f) This installation will require some parts unique to your aircraft that are not supplied with the kit,
(including but not limited to tie-wraps, hoses and fittings). Acquire all the necessary parts prior to
beginning the installation.
g) Do NOT use aluminum fittings with the FXT-201 or FXT-231 fuel flow transducer.
h) Write down the K-factor engraved on the side of the fuel flow transducer here _______. Once the
transducer is installed and covered with the fire sleeve, you will not be able to access this K factor.
i) Determine the locations of all holes before drilling to ensure that nothing interferes with the probe,
clamp, clamp screw or wire.
j) Provide service loops at the instrument.
k) Thermocouple wire length is not critical. Trim to required length, allowing for service loops at the engine
so that probes can be swapped with probes on adjacent cylinders for troubleshooting purposes.
l) Dress all wires away from high temperature components such as exhaust stacks.
m) Never splice thermocouple wire using copper wire. Use only K-type thermocouple wire. Solder using
zinc chloride flux such as Nokorode brand – rosin flux alone won’t work.
n) Observe correct polarity on all probe wires. Connect like colors together (red to red, yellow to yellow).
o) This instrument must be grounded at the engine, not at the avionics ground.
p) If a spark plug gasket probe is used, expect the CHT reading on that cylinder to be somewhat higher
than on the cylinders with bayonet probes. At additional cost an adapter probe (bayonet or screw-in) is
available that permits the factory CHT probe and the JPI probe to be placed in the same bayonet
location.

Produkt Specifikationer

Mærke: J.P. Instruments
Kategori: Ikke kategoriseret
Model: EDM-830

Har du brug for hjælp?

Hvis du har brug for hjælp til J.P. Instruments EDM-830 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret J.P. Instruments Manualer

J.P. Instruments

J.P. Instruments EDM-900 Manual

24 August 2024
J.P. Instruments

J.P. Instruments EDM-930 Manual

24 August 2024
J.P. Instruments

J.P. Instruments EDM-830 Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Rival

Rival CN753-W Manual

15 Juni 2025
Acopa

Acopa 553WSMKE Manual

15 Juni 2025
Atosa

Atosa RDCS-35 Manual

15 Juni 2025
Gourmia

Gourmia GAF692 Manual

15 Juni 2025
Taylor

Taylor 5315856 Manual

15 Juni 2025
Watts

Watts LF8B Manual

15 Juni 2025
Watts

Watts PLT-5 Manual

15 Juni 2025
ToiToiKids

ToiToiKids Fay Manual

15 Juni 2025
Astell&Kern

Astell&Kern PD10 Manual

15 Juni 2025
Aiphone

Aiphone JP-8Z Manual

15 Juni 2025