JUNG DAW360 Manual

JUNG Skifte DAW360

Læs gratis den danske manual til JUNG DAW360 (8 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11 anmeldelser. Har du et spørgsmål om JUNG DAW360, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Ceiling automatic switch

Light Management

Ceiling automatic switch

Art.-No.: DAW 360 WW

Ceiling automatic switch

Art.-No.: DAW 360 AL

Operating instructions

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Failure to observe the instructions may cause damage to the device and result in fire and

other hazards.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

The load is not electrically isolated from the mains even when the device is switched off.

Do not press on the sensor window. Device can be damaged.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

Figure 1

(1) Flush-mounted insert

(2) Motion detector cover

(3) Adjuster sens

(4) Adjuster time

(5) Adjuster lux

(6) Brightness sensor

(7) LED display, behind the lens

(8) Lens

(9) Decor ring

(10) Push-on cover

1/8

82563813

J:0082563813 17.11.2011

3 Function

Intended use

- Automatic switching of lighting depending on the heat motion and ambient brightness.

- Operation with concealed insert for dimming, switching or extension insert, 3-wire

- Ceiling installation on flush-mounted insert

Product characteristics

- Run-on time, sensitivity and brightness threshold settable

- Test operation for checking the detection area

- Short-time operation to control signal encoders

- Dimming phase in combination with dimming insert

- Saving a switch-on brightness with dimming inserts

- Dimming lights with dimming inserts

- Manual switch-on possible via extension insert, 2-wire, or installation button

- 78 lens segments in 5 recording levels

- Extension of the detection area in combination with the 3-wire extension insert

- Detection area can be limited using push-on cover

Automatic operation

The controller detects heat motions of people, animals and objects.

- The light is switched on if a person enters the monitored detection area and the brightness

is below the set threshold.

- The light is switched off if no more movement is detected in the detection area and the

follow-up time has elapsed.

Dimming phase with dimming insert

If the motion detector cover is fitted on a dimming insert, then when the run-on time elapses the

lighting is dimmed to minimum brightness and then switched off. The time from the start of

dimming to switching-off is always approx. 30 s. If a motion is detected during the dimming

phase, the motion detector switches the lighting to the stored switch-on brightness again.

Behaviour in case of a mains failure

- Less than 0.2 seconds: the old switching position is restored after mains return.

- 0.2 seconds to approx. 2 seconds: when the power returns, the lighting is switched on

again for the run-on time. Each detected movement restarts the run-on time again.

- Longer than 2 seconds: when the power returns, the motion detector carries out a brief

calibration process. Then the lighting remains switched on for the run-on time. Each

detected movement restarts the run-on time again.

LED display (7)

Main device Extension

LED lights up during the calibration process. LED lights up during the calibration process.

LED lights up when a motion is detected if the

lighting is switched off and the brightness is

not below the brightness threshold.

LED lights up when a motion is detected.

4 Operation

Switching on the light

A 2-wire extension or an installation button, NO contact is connected.

o Press extension or installation button.

Light is switched on independently of the brightness, with a dimming insert to switch-on

brightness. Automatic mode is active.

i After manual switch-on the run-on time is at least 2 minutes.

i Manual switch-on is not possible.

2/8

82563813

J:0082563813 17.11.2011

Light Management

Ceiling automatic switch

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Skifte
Model:	DAW360

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG DAW360 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte JUNG Manualer

JUNG W8180 Manual

10 December 2024

JUNG 201TE Manual

10 December 2024

JUNG ASLS1280-1 Manual

20 September 2024

JUNG ME5201DTU Manual

2 September 2024

JUNG SL1180 Manual

28 August 2024

JUNG AS5544.03VWW Manual

28 August 2024

JUNG ES5201DTU Manual

28 August 2024

JUNG SL1180-1 Manual

28 August 2024

JUNG CD5024WW Manual

28 August 2024

JUNG A1180-1 Manual

23 August 2024

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025