Kathrein ESO 124 H Manual

Kathrein Ikke kategoriseret ESO 124 H

Læs gratis den danske manual til Kathrein ESO 124 H (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Kathrein ESO 124 H, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1 / 4

ESO 90 H 237500001

ESO 120 H 237500002

ESO 124 H 237500003

ESO 124 HL 237500005

Reﬂector Heating System for CAS 90, CAS 120 and CAS 124

Features

•Flexible special heating mat with integrated thermal insulation

and PTFE-insulated heating elements

•Good heat distribution due to an optimal ﬁt of the heating mat

on the reﬂector

•Element carrier of aluminium foil, self-adhesive foil strips at

the front

•

Thermal insulation made of bubble wrap with reﬂective layer,

4 mm

•

Built-in sensor to additionally deﬁne the heating temperature

via a control

About These Instructions

This document is part of the product. These instructions

describe how to install and connect the reﬂector heating

systems ESO 90 H, ESO 120 H, ESO 124 H and ESO 124 HL.

►Do not install or use the device until you have read and

understood this document.

►

Keep this document for reference throughout the service life

of the device. Pass this document on to any new owner or

user.

The current version of this document can be found at

www.kathrein-ds.com

Scope of Supply

•1 x heating mat with 3 m cable (H05RNF) and heating tempe-

rature sensor

•

Mesh reinforced aluminium foil, 0.05 x 5 m

•Adhesive ﬁlm (white) for covering the aluminium foil,

0.075 x 5 m

•5 x cable ties, 360 mm

Transport and Storage

►

If possible, transport and store the heating mat in its original packaging.

►

Protect the heating mat against moisture and mechanical damage.

►

Transport and store the heating mat only in the permitted temperature range between -40 and +80°C. Make sure there is no

condensation build-up.

Functional Description

The electric heating system prevents snow and ice formation on the antenna reﬂector surface which may lead to interruptions in

satellite reception. The heating for the antenna consists of a special heating mat with an integrated thermal insulation and PTFE-insu-

lated heating elements. The installed heating mat ﬁts optimally on the reﬂector and guarantees good heat distribution. The heating

mat has an integrated temperature switch that turns o the heating at 80°C so that the system can be operated at 230 V/50Hz. To

ensure ecient operation, we recommend the use of a control unit, which can be operated with or without the built-in sensor.

Possible system components:

Operation without temperature

sensor

Operation with temperature sensor Operation without control possible

ESO 90/120/124 H ESO 005, ESO 96, ESO 97 ESO 97 SL Yes

ESO 124 HL - ESO 99 + ESO 101, ESO 97 SL No

ESO 90 H

•1 x heating mat with 3 m cable (H05RNF) and heating tempe-

rature sensor

•

Mesh reinforced aluminium foil, 0.05 x 8 m

•Adhesive ﬁlm (white) for covering the aluminium foil,

0.075 x 8 m

•5 segments (ESO 120 H) or 4 segments (ESO 124 H/HL) of

white adhesive foil for covering the outer contours of the

heating mats

•5 x cable ties, 360 mm

ESO 120 H, ESO 124 H, ESO 124 HL

ESO 90 H ESO 120 H

ESO 124 H/HL

ESO 124 HL:

For exposed locations, with

double the heating power

compared to ESO 124 H

(L = increased performance).

2 / 4

DANGER!

Danger to life from electric shock when touching electrical installations!

►Disconnect all devices and units from the power supply during installation.

►

In order to comply with the regulations for outdoor installation according to DIN VDE 0100 Part 610, it is recom-

mended to have a residual current circuit breaker with a residual current of 0.03 A installed.

►

Make sure that installation and connection are only carried out by qualiﬁed personnel.

►

Make sure that modiﬁcations to electrical installations are only carried out by a specialist. Do not make any unautho-

rised changes yourself.

Installation and Safety Instructions

WARNING!

Risk of severe injuries during installation due to falling from or through the roof or falling parts!

►

Wear sturdy shoes with non-slip soles.

►Use a working platform.

►

Make sure that the person carrying out the installation or repair has a secure position to stand and hold on whilst

working.

►

Make sure that the person carrying out the installation or repair does not suer from vertigo and can move around

safely on the roof or installation site.

►

Make sure that the vehicle roof is suciently strong and stable.

►

Make sure that there is nobody underneath the antenna during installation/dismantling.

Installing the Reﬂector Heating

Required tools and equipment

•Knife

•Scissors

Installing the heating mat

Processing temperature

The most favourable processing temperatures (object temperature and ambient temperature) are between +15°C and +30°C. Proces-

sing below these temperatures is not recommended. Below the recommended temperatures, the adhesive may become too hard and

thus not achieve the desired adhesion.

The build-up of condensation must be avoided in any case. Condensation may build up when the adhesive tape and/or the surfaces

to be bonded are moved from a cold to a warmer environment. If this is the case, sucient time must be allowed after transport and

before bonding, so that all joining parts have the same temperature in the range indicated above.

Intended Use

The ESO 90 H, ESO 120 H, ESO 124 H and ESO 124 HL are reﬂector heating systems for the antennas CAS 90, CAS 120 and CAS 124.

They are used to prevent snow and ice formation on the antenna reﬂector surface which could lead to interruptions in the satellite

reception. Any other use, or failure to comply with these instructions or documentation and instructions enclosed with the devices,

will result in voiding of warranty or guarantee. The following circumstances result in the loss of all warranty and liability claims

towards the manufacturer:

►Improper installation

►

Use of non-speciﬁed mounting materials, which cannot guarantee the mechanical reliability of the antenna system

►

Structural changes or interference with the components and mounting accessories in the kit, which could endanger both the

mechanical and functional reliability

►Failure to observe installation and safety instructions in these instructions

1. Clean and degrease the antenna back panel.

The surface to be bonded must always be dry, free from dust, grease, oil, oxides, separating agents and other contaminants.

Isopropanol, ethanol, acetone, ethyl acetate, toluene or petrol can be used to remove dust, grease, oil, separating agents and

other contaminants. Other standard cleaning agents that do not leave any residues are also suitable. Please observe the respec-

tive safety regulations of the manufacturers of the solvents and cleaning agents.

Produkt Specifikationer

Mærke:	Kathrein
Kategori:	Ikke kategoriseret
Model:	ESO 124 H

Har du brug for hjælp?

Hvis du har brug for hjælp til Kathrein ESO 124 H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kathrein Manualer

Kathrein UFO 97-18 HDMI/CI Manual

17 Juli 2025

Kathrein UFO 102 Manual

17 Juli 2025

Kathrein ESO 005 Manual

10 Juni 2025

Kathrein UFX 150/4 Manual

16 Februar 2025

Kathrein UFX 12 Manual

5 Februar 2025

Kathrein UFX 14 Manual

5 Februar 2025

Kathrein UFO 97-18 HDMI Manual

28 Januar 2025

Kathrein FMK 100b Manual

15 Januar 2025

Kathrein CAP 500M plus Manual

15 Oktober 2024

Kathrein UFO 83 Manual

28 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Chief TILD1X05US-R Manual

14 Oktober 2025

GBC W12 Manual

14 Oktober 2025

Fuxtec FX-CT100 Manual

13 Oktober 2025

Scotsman Prodigy Plus NH0422 Manual

13 Oktober 2025

Chief FCA800HS Manual

13 Oktober 2025

Chief OLCM1U Manual

13 Oktober 2025

IPEGA PG-P5V002 Manual

13 Oktober 2025

IPEGA PG-P5013 Manual

13 Oktober 2025

IPEGA PG-SW2210 Manual

13 Oktober 2025

IPEGA PG-P5042 Manual

13 Oktober 2025