Kathrein UWS 24 Manual

Kathrein Skifte UWS 24

Læs gratis den danske manual til Kathrein UWS 24 (4 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Kathrein UWS 24, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1 / 4

UWS 24 20550001

Wideband to Quatro Converter

About this Manual

This document is part of the product.

►Read this manual carefully before using the converter

for the ﬁ rst time.

►Keep this document for reference throughout the

service life of the device and pass it on to any new

owner or user.

For the most up-to-date version of this manual, go to

www.kathrein-ds.com.

Keep this manual in a safe place for future

reference and include it with the unit when

passing it on to the next user.

Features

■Converter for converting two wideband signals to four SAT-IF levels

■The use of terminating resistor EMK 03 (order no. 237169) enables the adaptation to the LNB‘s oscillator frequency

(10.40 GHz or 10.41 GHz)

■Power supply via “horizontal low” trunk

■Terrestrial signals in the 5–862 MHz band can be received even when the satellite receiver is switched oﬀ

■Installation on EXR 2508 (order no. 20510095) or EXR 2558 (order no. 20510096) possible using EMU 250 coupler

(order no. 20510044)

■Kathrein Power Saving:

If no receiver is active in a system using Kathrein Power Saving, both the LNB and the converter are switched oﬀ

Scope of Supply

■UWS 24

●Instructions for use for UWS 24

Transport and Storage

►Use the original packaging for transporting the device; store it in a dry place

►Make sure there is no water condensation build-up.

Intended Use

►The device described in this manual is only intended for the installation of satellite reception systems and may only

be installed by trained specialists

►Any other use or the non-observance of these instructions will result in the loss of the warranty and guarantee

►The manufacturer accepts no liability for accidents caused by the user opening the unit

►Opening the unit and attempting to repair it yourself voids all warranty claims

suitable for DVB-T/T2

44,1 63,45

111,5

148

134

205500001

UWS 24

Made in Germany

H Wideband

Conﬁg

V Wideband

Terr.

H low

V low

V high

H high

Open: LNB 10,40 GHz

Term:

18 V 18 V

Wideband - Quatro - Converter

Digital Systems GmbH

LNB

10,4 GHz1

2 / 4

Safety Precautions

Installation Instructions

Risk of damage to property!

Use a coaxial cable with an inner conductor diameter

of 1.2 mm max. and without any burrs. Ensure short-

circuit-free installation.

►Connectors for coaxial cables: 75 Ω RF connectors

(F series) according to EN 61169-24

►Use wood screws (max. Ø 4 mm) for fastening

►May not be installed in damp rooms

►Use recommended accessories only

Max. 2 mm

excess length

Clamping torque

max. 3.4 Nm

(danger of over-

winding)

Diameter

0.6 - 1.2 mm free of burrs

Improper intervention can endanger the electrical safety of the device.

►Do not open or tamper with the unit

►Always disconnect the mains plug from the socket when working on the system

►Ensure adequate clearance: at least 5 cm to all sides

►Ensure free circulation of air to dissipate the heat from the unit

►Do not place any liquid-ﬁ lled items on top of the device

►Do not expose the device to dripping or splashing water

►Admissible ambient temperature: -20 to +55°C

►The device may only be installed in dry indoor areas

►Do not install the device on or against easily combustible material

►The device is intended for wall mounting only! All other installation positions are prohibited

►Comply with the safety regulations set out in the current EN 60728-11 and EN 62368-1 standards

►The equipment must be provided with an equipotential bonding wire (Cu, at least 4 mm

Input level:

To prevent overloading of the inputs, the level must not exceed 80 dBµV per transponder.

For higher input levels (> 80 dBµV) we recommend to use an attenuator (e.g. ERE 01 with 6 dB, order no.

274854).

Observe the oscillator frequency of the LNB:

Wideband feed systems using an oscillator frequency of 10.41 GHz are available on the market. To be able

to use these, screw an EMK 03 terminating resistor onto the “conﬁ g” socket. The change is eﬀ ective imme-

diately.

This is not required when using the Kathrein feed system UAS 582 (order no 20110032.

Produkt Specifikationer

Mærke:	Kathrein
Kategori:	Skifte
Model:	UWS 24

Har du brug for hjælp?

Hvis du har brug for hjælp til Kathrein UWS 24 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Kathrein Manualer

Kathrein EXR 2998 Manual

5 December 2024

Kathrein EXR 2908 Manual

4 August 2024

Kathrein EXD 2532 Manual

3 August 2024

Kathrein UWS 24 Manual

1 August 2024

Kathrein EXD 154 Manual

29 Juli 2024

Kathrein EBX 2920 Manual

19 Juli 2024

Kathrein EXI 3508 Manual

1 September 2023

Kathrein EXD 258 Twin Manual

16 Februar 2023

Kathrein VWS 2900 Manual

15 Januar 2023

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025