Kicker 50HDR154 Manual

Kicker Ikke kategoriseret 50HDR154

Læs gratis den danske manual til Kicker 50HDR154 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 90 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 45.5 anmeldelser. Har du et spørgsmål om Kicker 50HDR154, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Remove the seat and disconnect both positive and negative battery terminals.

Remove the windshield and outer fairing.

Once the windshield screws are removed, gently pull off the top vent/cowl piece. There are two plastic retainer clips that hold it on.

Remove your stock speaker grilles. Push them out from the inside of the fairing. They are fastened with a plastic retainer clip. Fig 1.

Fig 1.

Fig 1.Fig 1.

Unplug the turn signals. Fig 2.

Fig 2.

Fig 2.Fig 2.

Remove the lower T25 fasteners holding the air deﬂ ectors to the inner fairing. Fig 3.

Fig 3.

Fig 3.Fig 3.

Remove the 3/16” allen bolts holding the turn signals to the inner fairing. Fig 4.

Fig 4.

Fig 4.Fig 4.

While holding the fairing, carefully remove the two T30 bolts behind the speaker grilles to remove the outer fairing and set aside. Fig

Fig

FigFig

5.5.

Remove the fuel tank.

Remove the console.

Unplug the fuel ﬁ tting on the left side of the tank.

Remove all four T40 mounting bolts and carefully lift the tank off the bike and set aside.

Remove wiring caddy cover.

Carefully release each tab along the caddy until it lifts completely. Fig 6.

Fig 6.

Fig 6.Fig 6.

SPEAKER INST

SPEAKER INSTSPEAKER INSTALLA

ALLA

ALLAALLATION

TION

TIONTION

Remove your stock speakers and replace them with your new PSC652 speakers in the kit.

Install the speaker into the pod and fasten with the original speaker screws. Fig

Fig

Fig Fig .

50HDR154

Motorcycle Audio Kit Installation Guide for

Harley Davidson® Road Glide (FLTR) 2015–Newer

Package Contents:

Package Contents:Package Contents:

(1)

Install Guide

(2)

PSC652 KICKER Speakers

(1)

Wiring Harness

(2)

8-32 x 1/2” Button Head Bolts

(1) KICKER Amp KPX3004 (2) 8-32 Nylock Nuts

(6) Black Cable Ties

(1) Ampliﬁer Mounting Bracket

Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper

procedures and torque speciﬁ cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit

may not

may notmay not

be compatible with some aftermarket head units.

PROGRAMMING HD RADIO

PROGRAMMING HD RADIOPROGRAMMING HD RADIO

NOTE:

NOTE:NOTE: It is necessary to re-ﬂash your HD radio before installation of this kit.

GETTING ST

GETTING STGETTING STARTED

ARTED

ARTEDARTED

HARNESS INST

HARNESS INSTHARNESS INSTALLA

ALLA

ALLAALLATION

TION

TIONTION

Route speaker wires to their respective connectors. Fig. 2

Fig. 2

Fig. 2Fig. 2

Separate the speaker connectors and plug in the ampliﬁer harness to each speaker. Fig. 8 & Fig. 8a

Fig. 8 & Fig. 8a

Fig. 8 & Fig. 8aFig. 8 & Fig. 8a

Plug the switched power harness into the 2-pin amp connector on the throttle side. see also, Fig. 2 for location)

Fig. 9 (

Fig. 9 (Fig. 9 (

Plug the blue wire on the kicker harness into the switched power harness lead with one wire. Fig. 9

Fig. 9

Fig. 9Fig. 9

This allows for an accessory 12V port to remain available.

Route both power leads along the clutch side of the neck and through the electrical and rear speaker output plug

caddy to the seat area.

Allen 3/16"

Tools Needed:

Tools Needed: Tools Needed: 10mm

wrench or socket

Torx T-30

Allen 9/64"

Phillips head screw driver

Torx T-40

11/32" wrench or socket

Torx T-25

(1) Mylar cover

(1) Dummy Plug

SYSTEM SETUP - Fig. 13

SYSTEM SETUP - Fig. 13SYSTEM SETUP - Fig. 13

Note: At this time, it is highly recommended to . KICKER recommends that the be set up as follows:

set the amp gain to 0

set the amp gain to 0set the amp gain to 0 dip switches

dip switches

dip switchesdip switches

Input Gain controls – 0

Fader – On Input

level – HI 



HI-PASS – Amp 1: 80 Hz (For Front)

Amp 2: 60Hz (6 x 9) 

80Hz (6.5” Tour Pack)

14. Plug the radio in, but do not reinstall it until the gain has been set.

15. if you are not using rear speakers it is recommended to Test component function and set the gain to optimize system performance.

leave the amp 2 gain turned all the way down.

16. Carefully reassemble the motorcycle and enjoy your new audio system!

Note: If you are not using rear speakers you will need to connect the Dummy Plug (fig. 15) to the rear speaker connector under the seat.

For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00 am – 5:00 pm CST or email at support@kicker.com.

KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 50 30523HDR154-F-202

10.

Remove the radio.

Unplug the four connectors on the back of the radio.

Remove the four 3/16" allen head bolts holding the radio to the chassis.

Gently remove the radio from the chassis.

11.

Install the KPX300.4 ampliﬁer onto bracket with supplied hardware.

Slide the end of the ampliﬁer with the power connector port into the bracket and fasten with supplied hardware.

Install the 9/64" allen head bolts from the bottom and fasten the 11/32" locknuts onto the ampliﬁer. Fig. 10

Fig. 10

Fig. 10Fig. 10

12.

Carefully install bracket/ampliﬁer assembly onto radio chassis by installing the assembly through the radio face port in the fairing and sliding the

tabs of the bracket over the chassis. Fig 11

Fig 11

Fig 11Fig 11

a.a.

Bracket must be angled through radio opening. Fig. 11a

Fig. 11a

Fig. 11aFig. 11a

13.

Attach amplifier to the harnesses power, speaker and input signal plugs. Fig. 12

Fig. 12

Fig. 12Fig. 12

AMP INST

AMP INSTAMP INSTALLA

ALLA

ALLAALLATION

TION

TIONTION

1212

1111

11a

11a11a

8a8a

1010

1313

1414

Note: At this time it is highly recommended to use the included Mylar sticker to cover the dip switches as seen in Fig. 14

Fig. 14

Fig. 14Fig. 14

115

Produkt Specifikationer

Mærke:	Kicker
Kategori:	Ikke kategoriseret
Model:	50HDR154

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker 50HDR154 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kicker Manualer

Kicker Premium 51MSS65 Manual

5 Februar 2025

Kicker Premium 51MSS8 Manual

5 Februar 2025

Kicker 51MWLE104 Manual

13 Januar 2025

Kicker 50HDS962 Manual

2 September 2024

Kicker 50HDR154 Manual

2 September 2024

Kicker 50HDS144 Manual

2 September 2024

Kicker SF150SC15 Manual

22 Februar 2024

Kicker KMLC Manual

28 Oktober 2022

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan 1024W Manual

15 Juni 2025

Backyard Pro 554PL2030 Manual

15 Juni 2025

Haier 1U18TE2HDA Manual

15 Juni 2025

AEG EWKEXT1 Manual

15 Juni 2025

Planet XGPN-400AXV Manual

15 Juni 2025

Cadac 3 Cook Turbo Manual

15 Juni 2025

Bobrick B-3944 Manual

15 Juni 2025

Sony SZC-4008 Manual

15 Juni 2025

Watts ETX-15 Manual

15 Juni 2025

Sigma REMOTE ONE Manual

15 Juni 2025