Lancom AirLancer IN-Q180+ Manual

Lancom Ikke kategoriseret AirLancer IN-Q180+

Læs gratis den danske manual til Lancom AirLancer IN-Q180+ (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 62 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 31.5 anmeldelser. Har du et spørgsmål om Lancom AirLancer IN-Q180+, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

LANCOM Antenna

AirLancer IN-Q180+

MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS

Preparation for wall- and ceiling mounting

Use the antenna as a drilling template to mark out the

drill holes for wall- or suspended ceiling mounting. The

horizontal and vertical separation of the adjacent holes is

104mm.

For ceiling mounting, if required, drill a hole into the center

of the ceiling board to feed-through the connector cables.

Alternatively, you can use the integrated cable duct on the

antenna backside to lead the cables sideways.

Size of the drill holes

Using the markings as a guide, drill the holes and insert

dowels for wall mounting, if appropriate. Depending on the

surface material the required size of the holes may vary.

Mounting the antenna

1. Ceiling board mounting with screws and nuts

Included: 4 thread screws 30 mm, 4 washers, 4 nuts

From the frontside, stick the thread screws through the

appropriate holes of the antenna housing and the previ-

ously drilled holes of the ceiling board. Place the washers on

the screws from the backside of the ceiling board. Finally,

use the nuts for ﬁxing.

2. Ceiling mounting with screws and clips

Included: 4 clips, 4 thread screws 15 mm

Push the clips into the appropriate slides at the backside

of the antenna, so that the clips are placed in line with

the holes in the antenna housing. Stick the thread screws

through the holes in the antenna housing from the front

side and loosely connect the screws to the clips.

Now the antenna can be moved onto the existing or addi-

tionally mounted metal ceiling t-bars. Finally, tighten the

screws for proper ﬁxing.

3. Wall mounting with screws & dowels

Included: 4 screws, 4 dowels

Place the antenna with its backside at the wall so that the

holes in the antenna housing are in line with the previously

inserted dowels. Stick the screws through the holes of the

antenna housing into the dowels and tighten the screws.

Important

Working responsibly with high frequencies

For compliance with protection requirements of the EU directive 2014/53 and EN 62479 in relation

to the basic limits for human safety in electromagnetic ﬁelds and the “FCC Policy on Human Expo-

sure to Radiofrequency Electromagnetic Fields”, it is essential to conﬁgure the accurate antenna

gain value in the Wi-Fi router or Wi-Fi access point.

Important

Electrical and electronic equipment law

In the interests of recycling, please do not dispose of electrical and electronic waste in your house-

hold garbage. Ensure that your electrical and electronic waste is disposed of in accordance with

the regulations in your country.

Important

Proper handling of antenna cables

Antenna cables are sensitive RF cables. During installation it is important that the cables are not

creased and bent as little as possible, otherwise the antenna will suffer a loss in performance. Do

not coil the antenna cable in tight loops.

Important

Antenna gain and terminating unused antenna connectors on the access point

It is essential to terminate unused antenna connectors on the access point with the supplied rod

antenna. The terminating resistor supplied with the adapter AirLancer AN-RPSMA-NJ is suitable

for use with indoor access points. In addition, you have to disable unused antenna connectors in

LCOS (changing the antenna grouping of the respective Wi-Fi module), and conﬁgure the antenna

gain. The settings can be found in LANconﬁg, resp. in the detail conﬁguration of the LANCOM

Management Cloud at: Conﬁguration > Wireless LAN > General > Physical WLAN settings > Radio

Ø7,5 mm

60 mm

30 mm

Technical details 2.4 GHz 5 GHz

Antenna characteristics 2.4 GHz 5 GHz

Mechanical details

Item

Antenna patterns

Produkt Specifikationer

Mærke:	Lancom
Kategori:	Ikke kategoriseret
Model:	AirLancer IN-Q180+

Har du brug for hjælp?

Hvis du har brug for hjælp til Lancom AirLancer IN-Q180+ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Lancom Manualer

Lancom AirLancer ON-D9a Manual

31 August 2024

Lancom AirLancer ON-QT60 Manual

31 August 2024

Lancom AirLancer IN-H180 Manual

31 August 2024

Lancom AirLancer ON-QT90 Manual

31 August 2024

Lancom AirLancer IN-Q180+ Manual

31 August 2024

Lancom SFP-GPON-1 Manual

30 August 2024

Lancom SFP-LR-LC25 Manual

30 August 2024

Lancom SFP-LR40-LC10 Manual

30 August 2024

Lancom SFP-SX-LC1 Manual

30 August 2024

Lancom SFP-SX-LC10 Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan VBP15SL Manual

17 September 2025

Rocktrail IAN 463536 Manual

17 September 2025

Kimo KNT 320 Manual

17 September 2025

Vestil LPRO-36-16-4 Manual

17 September 2025

Vestil CPC-20 Manual

17 September 2025

Vestil UNI-4048-4-BLU-230-1 Manual

17 September 2025

Vestil CANT-3648 Manual

17 September 2025

InLine 16277S Manual

17 September 2025

Vestil H-75-LD Manual

17 September 2025

Fulgor Milano P1B 5343 QU Manual

17 September 2025