Lancom OW-602 Manual

Lancom Adgangspunkt OW-602

Læs gratis den danske manual til Lancom OW-602 (4 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Lancom OW-602, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

LANCOM Antenna Distance Calculator

lancom-systems.com

This guide to the Antenna Distance Calculator supports you in using this tool to

determine the data transfer rates depending on the distance of the antennas of an

outdoor point-to-point (P2P) Wi-Fi connection.

After the calculation you get a tabular overview as well as a diagram of the expected

gross data transfer rates, broken down by the possible channel widths.

Step-by-step instructions

LANCOM Antenna Distance Calculator2

lancom-systems.com

LANCOM Antenna Distance Calculator

Selection of hardware parameters

Start with and select the access point to be used there under Location A Access

point / client adapter Wi-Fi chipset. The installed of the selected access point is

automatically displayed in the next field.

If the access point has an alternative chipset for a different frequency band, you can

select it here.

If available, select the chipset that operates in the 5 GHz band to achieve higher

ranges.

In the next field, the selected should correspond to the most modern Wi-Fi standard

one supported by the chip (802.11ac > 802.11n > 802.11a/g).

Then select the to be used. The cable to be used between access antenna (Cable 1)

point and antenna at location A is determined in the next step.

If you need a surge arrester for the outdoor installation, please select it in the

following field.

The installation of the surge arrester requires an additional cable between it (Cable 2)

and the access point, which you specify in the next field.

If you select a non-standard cable, you have the option to specify the cable

attenuation here. Note that the value must be specified for the total cable length to

be used.

The configuration for location A is now complete. Proceed with the entries for

locationB in the same way.

Produkt Specifikationer

Mærke:	Lancom
Kategori:	Adgangspunkt
Model:	OW-602

Har du brug for hjælp?

Hvis du har brug for hjælp til Lancom OW-602 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Adgangspunkt Lancom Manualer

Lancom LX-7500 Manual

6 September 2024

Lancom LX-7300 Manual

6 September 2024

Lancom LN-862 Manual

30 August 2024

Lancom LX-6400 Manual

16 August 2024

Lancom LW-500 Manual

16 August 2024

Lancom OW-602 Manual

15 August 2024

Lancom LN-1702B Manual

15 August 2024

Lancom OX-6400 Manual

14 August 2024

Lancom LW-600 Manual

13 August 2024

Lancom LX-6402 Manual

10 August 2024

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

Cudy AP11000 Manual

3 Juni 2025

Planet WDAP-C5100BE Manual

5 April 2025

Peplink AP One AX Manual

20 Marts 2025

Cisco Aironet 3600i Manual

15 Januar 2025

Cisco Aironet 3600e Manual

13 Januar 2025

Luxul P40 Manual

13 Januar 2025

Luxul XAP-1440 Manual

13 Januar 2025

Ubiquiti Networks UniFi AP Flex HD Manual

12 Januar 2025

TP-Link Omada EAP115-Wall Manual

30 December 2025

D-Link DBT-900AP Manual

26 December 2024