) y
( ) los botones al mismo tiempo hasta que el despliegue refleje
º Centígrado. Apretar los mismos botones otra vez cambiarán la
espalda del despliegue a º Fahrenheit. La Calefactora repondrá
a º Fahrenheit después que para ser quitado.
7. La unidad visualizará la temperatura “Room” (ambiente) actual.
Al encender el Calefactor, la unidad estará en el modo de
calefacción (alto). (1500 vatios)High
8. Si oprime el (mode) en este momento, el Botón De Mode
Calefactor funcionará en el modo de calefacción (bajo). Low
9. Si oprime una vez más el Botón De Mode (mode), el Calefactor
funcionará en el modo (alto). High
10. Pa ra g irar la Calefactora L EJ OS, a pr etar el Botón De
Encendido ( ) y quitar la unidad de la salida eléctrica.
CONTROL AUTOMÁTICO DE LA TEMPERATURA (Figura 3)
La función de temperatura automática sólo operará en calefacción
“Alta” ( ). No puede fijar la temperatura automáticamente cuando
la unidad se encuentre en la modalidad de calefacción baja.
1. Para fijar una temperatura específica en la habitación, presione
los botones de (+) o (-) hasta la temperatura deseada. La
pantalla mostrará la letra (A) y la temperatura estará iluminada.
El Calefactor ahora se encuentra en la modalidad de temperatura
automática.
2. Cuando alcance la temperatura en la cual desea establecer la
unidad, la temperatura fijada titilará varias veces y luego la pantalla
volverá a indicar la temperatura actual y cambiará gradualmente
a medida que cambia la temperatura de la habitación. NOTA:
la pantalla de la temperatura no indica la temperatura del aire
caliente emitido por el Calefactor.
3. Una vez que la temperatura de la habitación alcanza los 2 grados
por encima de la temperatura fijada, el Calefactor se apagará.
Una vez que la temperatura de la habitación alcanza 1 grado por
debajo de la temperatura fijada, el Calefactor se encenderá de
nuevo y continuará con el ciclo de apagado y encendido para
mantener la temperatura fijada.
4. Esta función se cancelará si el botón De Mode está presionado.
Ahora el Calefactor estará en calefacción “Alta” (III) y operará
continuamente.
Función automática de muestra de aire: Funciona sólo
cuando se fija el calefactor en la modalidad automática. Es normal
que el ventilador del calefactor opere durante aproximadamente
15 segundos después de que el calefactor ha alcanzado la
temperatura fijada. A partir de ese momento, el ventilador del
calefactor se encenderá cada 10 minutos durante 10 segundos
hasta que la habitación requiera calefacción adicional.
Figura 3
OSCILACIÓN
Oprimir el le permitirá al Calefactor Botón de Oscilación (OSC)
oscilar hacia atrás y hacia delante. Para detener la oscilación,
vuelva a oprimir el Botón de Oscilación (OSC). Cuando el calefactor
esté en control automático de temperatura, la función de oscilación
se detendrá cuando se alcance la temperatura fijada y reiniciará
cuando el calefactor vuelva a encenderse.
Figura 4
Vista Posterior del Calefactor
El gancho del control remoto está ubicado en la parte posterior del
calefactor. (Figura 4)
La pantalla refleja calor Alto y Función de
Control Automático de Temperatura
Figura 2
Función de
Temporizador en
Calor Bajo
Función de Temporizador
en Calor Alto y Control
Automático de Temperatura
Figura 1
Pantalla
Pantalla al ser encendido por primera vez
(Figura 1 a 3)
Luz de Encendido
FUNCIÓN DE TEMPORIZADOR (Figura 2)
La función de temporizador puede ser activada cuando la pantalla
del Calefactor está en cualquier función o velocidad. Esta función
le permite fijar la cantidad de tiempo que el Calefactor estará
funcionando antes de apagarse automáticamente, de 1 hora
a 8 horas. Presionar el Botón de Temporizador ( ) aumentará
la cantidad de tiempo en 1 hora cada vez que dicho botón sea
oprimido. Después que la pantalla refleje 8 horas, si presiona el
Botón de Temporizador ( ) una vez más, se reiniciará el Calefactor
para función continua. El Calefactor se apagará cuando el
tiempo fijado haya transcurrido. La unidad puede ser encendida
nuevamente presionando el (Botón de Encendido ).
1. ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG HEATER
INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL
OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL
OUTLET ONLY.
WARNING: FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY
INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A
QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET.
2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury
to persons.
3. Make certain that the room is equipped with a working smoke detector.
4. Make certain that the power source conforms to the electrical requirements of the Heater.
5. Extreme caution is necessary when any Heater is used by or near children or invalids a nd whenever the Heater is lef t operating
unattended.
6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polar-
ized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
7. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. Please
contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
8. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
9. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
10. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the
Heater. Do not block or tamper with the Heater in any manner while it is in operation.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become
blocked.
12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so
the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or
similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep com-
bustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them
at least 1 foot (0.3 m) from the sides and rear.
14. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored.
DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This Heater is intended for general use
ONLY.
15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
16. DO NOT use Heater outdoors.
17. Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move the
Heater to another location.
18. Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.
19. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
20. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to
National Electric Code (NEC) Art icle 547-7 (2008), or applicable state or local codes or standards relating t o electrical requirements for
Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
21. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes
or standards relat ing to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC
ARTICLE 500 (2008).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk
of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND
UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE
HEATER IS ON OR PLUGGED IN.
SAVE THESE INSTRUCTIONS
