IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fi re, electrical shock, injury to persons and hyperthermia:
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS FOLLOW
THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
Plug heaters directly into a 120v wall outlet/receptacle only. Never use with an extension cord. Do not plug heater into any other cord. Plug
heaters directly into a 120v wall outlet/receptacle only. Never use with an extension cord. Do not plug heater into any other cord connected
device, such as a power strip, surge protector, multiple outlet adapter, cord reel or outlet-type air freshener. The use of such devices may create a
fi re hazard. Do not plug multiple devices in the same outlet or on same circuit as heater.
Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug fi ts tightly into outlet before each use. During use,
check to make certain the heater plug is not overheating. If necessary have a qualifi ed electrician check and/or replace the wall outlet. Do not use
this heater with any solid state speed control devices.
Make certain that the power source conforms to the electrical requirements of the heater.
Extreme caution is necessary when any heater is used by or near children or invalids. The heater should not be left operating unattended. Never
leave children unattended when the heater is on or plugged in.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fi t in a
polarized outlet only one way. If the plug does not fi t fully in the outlet, reverse the plug. If it still does not fi t, contact a qualifi ed electrician. Do not
attempt to defeat this safety feature.
Do not use the heater in areas where gasoline, paint, or fl ammable liquids are used or stored. Do not use heater in locations where fl ammable or
explosive chemicals are stored, or in wet atmospheres.
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, or has been dropped or damaged in any manner. To
disconnect heater, turn the heater off then remove the plug from the outlet.
Always unplug heater when not in use. Unplug power cord before servicing or moving the heater.
Do not insert or allow fi ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fi re, or damage the
heater. Do not block or tamper with the heater in any manner while it is in operation.
Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness,
fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seekmedical attention.
To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confi ned space around
infants, or individuals with reducedphysical, sensory, or mental capabilities.
• Always unplug heater when not in use. Unplug power cord before servicing or moving the heater.
• Do not insert or allow fi ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fi re, or damage
the heater. Do not block or tamper with the heater in any manner while it is in operation.
• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
• Always place the heater on a stable, fl at, level surface when operating, to avoid the chance of the heater overturning. Locate the power cord
so the heater or other objects are not resting on it. Do not run power cord under carpeting. Do not cover power cord with throw rugs, runners,
or similar coverings as this may cause cord to overheat. Arrange power cord away from room traffi c and where
it will not be tripped over.
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this heater. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 M) from the front of the heater and
keep them at least 1 foot (0.3 M) from the sides and rear.
• This heater is not intended for use in wet or damp locations. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate a heater where it may fall into a bathtub or other water container.
• Do not use heater outdoors.
• This heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confi ned. Please refer
to national electric code (nec) article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for
agricultural buildings. This heater does not meet the requirements of nec article 547-7 (2008).
• This heater is not suitable for use in hazardous locations. Please refer to national electric code (nec) article 500 or applicable state or local
codes or standards relating to electrical requirements for hazardous locations. This heater does not meet the requirements of
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this heater. If this occurs, move
the heater to another location.
• Keep heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the heater.
• Install two “AAA” batteries (included).
• Do not mix old and new batteries. Do not mix al ka line, stan dard (carbon-zinc)
or rechargeable (nickel-cad mi um) batteries.
• Do not dispose of batteries in fi re. Batteries may explode or leak.
• Always purchase the correct size and grade of battery most suitable
• Replace all batteries of a set at the same time.
• Clean the battery contacts and also those of the device prior to battery
• Ensure the batteries are installed correctly with regards to polarity (+ and -).
• Remove batteries from equipment that is not to be used for an
• Remove used batteries promptly.
Read all instructions before using this Heater. Save these instructions
Al presionar los botones ( ) o ( ) mientras se encuentra en las confi guraciones de energía ALTA o BAJA, se encenderá la función Auto Eco
1. Para fi jar una temperatura específi ca en la habitación, presione los botones (
) o ( ) hasta la temperatura deseada. La pantalla ahora refl ejará el símbolo de
y la temperatura destellará. El Unidad está ahora en modo Auto Eco
2. Cuando se alcance la temperatura en la cual desea establecer la unidad, la temperatura fi jada destellará varias veces y luego la pantalla volverá a indicar
la temperatura ambiente actual y cambiará gradualmente a medida que cambie la temperatura ambiente. NOTA: La pantalla de la temperatura no indica la
temperatura del aire caliente que emite el Unidad.
3. El calentador funcionará a ALTO calor cuando la temperatura ambiente sea menor que la temperatura establecida.
4. El calefactor funcionará con BAJA temperatura cuando la temperatura ambiente alcance la temperatura establecida y seguirá funcionando con BAJA temperatura
hasta que la temperatura ambiente alcance 2 grados Fahrenheit por encima de la temperatura establecida.
5. El calentador se apagará una vez que la temperatura ambiente sea superior a 2 grados Fahrenheit por encima de la temperatura establecida. El ventilador seguirá
funcionando durante 15 segundos después de que se apague el elemento calefactor.
Todo esto ocurre automáticamente con la tecnología Auto Eco
de Lasko. Para desactivar la función Auto Eco
, apague el Unidad o presione el botón Modo
NOTA: En el modo Auto Eco
, el Calentador mostrará la temperatura ambiente actual en grados Fahrenheit. Presione los botones ( ) y ( ) al mismo tiempo
para mostrar los grados Celsius. Presione los mismos dos botones juntos nuevamente para volver a mostrar los grados Fahrenheit.
Presione para Disminuir la temperatura ambiente deseada.
Bloqueo de niños (cuando se mantiene con Temp -
Presione para Aumentar la temperatura ambiente deseada.
Bloqueo de niños (cuando se mantiene con
Temp - durante 3 segundos)
Botón de Oscilación de Base
Presione para Iniciar/Detener la función de oscilación de la base.
El temporizador se puede con gurar hasta 12 horas. fi
0.5 - 12.0 horas en intervalos de 0.5 horas hasta 2 horas,
incrementos de 1 hora de 2 horas a 12 horas. Continúe
presionando el botón del temporizador para alcanzar la
con guración de tiempo deseada. La luz del temporizador fi
se vuelve roja cuando se activa.
BLOQUEO DE NIÑOS (Desactivar):
Para desactivar el bloqueo infantil, pulse el botón ecológico automático (+) y
el botón ecológico™ automático (-) juntos durante 3 segundos. La función de
bloqueo para niños se desactivará.
Desenchufar la unidad también desactivará la función de bloqueo para niños.
Pulse el botón MODO NOCTURNO del mando a distancia para activar /
desactivar el modo nocturno. El icono del BOTÓN DE CALOR se iluminará
para reconocer que el modo nocturno está activado y todos los demás
iconos se apagarán. Al tocar cualquier botón de la unidad o control remoto,
activará la pantalla durante 10 segundos.
BLOQUEO PARA NIÑOS (Activar):
Cuando el botón Auto Eco (+) y el botón Auto Eco™ (-) se mantienen juntos durante
3 segundos, todos Las funciones del calentador están desactivadas, excepto el
botón de encendido. Todas las funciones que se encuentran actualmente activado
permanecerá encendido. El segement dispays mostrará “CL”.
El calor se puede ajustar a H3 (Alto), H2 (Medio) o H1 (Bajo).
ENCENDIDO/APAGADO el Calefactor presionando el
1 4 Cuerpo Control Remoto
Coloque la unidad sobre una mesa
resistente para facilitar el montaje de la
base. Empuje la ensamblada sobre el base
cuerpo de la unidad, tal como se muestra.
1. Alinee las ranuras de la con las base A
lengüetas de la base B. Encájelas.
Sostenga la estructura en su lugar mientras
gira el ensamblaje de la base de soporte en
el sentido de las agujas del reloj hasta que
