Lectrosonics LRBATELIM Manual

Lectrosonics Mikrofon LRBATELIM

Læs gratis den danske manual til Lectrosonics LRBATELIM (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Lectrosonics LRBATELIM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

LRBATELIM-H

Battery Eliminator (only for LR receiver)

TECHNICAL DATA

Rio Rancho, NM, USA

www.lectrosonics.com

This battery eliminator replaces the batteries and door

on the LR receiver, allowing the unit to be powered from

an external DC source. The battery eliminator is sup-

plied in a kit including mounting screws.

P/N 28615 (2-56 1/8 FL100)P/N 28623 (2-56 5/16 FL100)

Removing the Battery Door

Save the door

assembly parts for

re-installation later

Remove

these

screws

Insert the battery eliminator as shown below and fasten

it with the supplied screws.

P/N 28623 (2-56 5/16

FL100) screws

P/N 28615 (2-56 1/8

FL100) screw

CAUTION: Use only the shorter screw

P/N 28615 (2-56 1/8 in.) in the hole near

the connector. The longer screws may

damage a circuit board component.

Tighten all three screws snugly, but be careful not to

overtighten them and damage the threads.

Optional power cable:

PS200A - 15” power cable, Hirose 4 to DC locking con-

nector with .365 in (9.3mm) plug.

5 Dec. 2024

581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com

(505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.co

Replacing the Battery Door

Separate part numbers for the battery door assembly

are as follows.

NOTE: The insulator, shorting bar and batt door

are factory assembled with an adhesive.

P/N 28623

2-56 5/16”

P/N 27033

spring detent

P/N 28615

2-56 1/8”

P/N 26985

batt door

P/N 26896

shorting bar

P/N 26986

latch plate

P/N P1293

insulator

Assemble the battery door and latch plate.

Specications

Input voltage range: 5 to 25 VDC

Current consumption: 310mA @ 5V, 130mA @ 12V, 65mA @25V

Dimensions: 53 x 60 x 21 mm (2.09 x 2.38 x .84 inches)

Weight: 23 grams (0.81 ozs.)

Tabs

Align holes

Place the spring detent

clip on the housing with

the tabs facing upward

and the screw hole

aligned with the one in

the housing.

Mount the latch plate-

and door assembly on

top of the spring detent

and align the screw hole. Insert the shortest screw (P/N

28615 2-56 1/8”) into the hole and tighten.

CAUTION: Use only the 1/8” screw. The

longer ones may damage the circuit board

inside.

As you tighten the

screw, the latch plate

and door pivot will

align the spring detent.

Tighten the screw

snugly, but not so tight

it damages the threads.

Close the door and make sure it latches correctly. If so,

then insert and tighten the two screws on the outside of

the housing. Use the longest screws (P/N 28623 2-56

5/16”).

Tighten the two

screws on the

outside of the

housing.

FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in-

terference in a residential installation. The equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit dierent from

that which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modications to this equipment not expressly approved by

Lectrosonics, Inc. could void the user’s authority to operate it.

LRBATELIM

Tested to comply

With FCC Standards

FOR HOME OR OFFICE USE

External DC Power Supply

External power is required via

Hirose 4 locking connector wired

per the diagram.

Produkt Specifikationer

Mærke:	Lectrosonics
Kategori:	Mikrofon
Model:	LRBATELIM

Har du brug for hjælp?

Hvis du har brug for hjælp til Lectrosonics LRBATELIM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Lectrosonics Manualer

Lectrosonics LRBATELIM Manual

8 Oktober 2025

Lectrosonics LTBATELIM Manual

8 Oktober 2025

Lectrosonics SMWB/E07-941 Manual

19 September 2025

Lectrosonics SMDWB/E07-941 Manual

19 September 2025

Lectrosonics SMV Manual

19 September 2025

Lectrosonics DSSM Manual

19 September 2025

Lectrosonics SSM Manual

18 September 2025

Lectrosonics Hma Manual

18 September 2025

Lectrosonics VRT2 Manual

1 September 2025

Lectrosonics UMCWBD-L Manual

28 Januar 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

8 Oktober 2025

8 Oktober 2025

8 Oktober 2025

8 Oktober 2025

8 Oktober 2025

TOA IR-310BC US Manual

8 Oktober 2025

TOA WS-5325U Manual

8 Oktober 2025

Sennheiser SL HEADMIC 1 BK Manual

8 Oktober 2025

TOA WM-5325 Manual

8 Oktober 2025

Evno BSX1 Manual

8 Oktober 2025