Lowrance EP-15 Fluid Level Manual

Lowrance Ikke kategoriseret EP-15 Fluid Level

Læs gratis den danske manual til Lowrance EP-15 Fluid Level (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 33 anmeldelser. Har du et spørgsmål om Lowrance EP-15 Fluid Level, eller vil du spørge andre brugere om produktet?

Side 1/8
1
Pub. 988-0154-371
EP-15 Fluid Level
Electronic Sensor
Installation Instructions
This instruction sheet tells how to install your EP-15 Fluid Level
sensor and connect it to a NMEA 2000 network using LowranceNET
network components. You must refer to your digital gauge, sonar or
GPS unit's manual for sensor operation instructions.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
Some sonar or GPS units may require a software upgrade to display
NMEA 2000 data correctly and a manual addendum describing how to
operate the sensor. You can download these free and get additional
information on the NMEA 2000 compatible LowranceNET system at
our web site, .www.lowrance.com
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending. See our web site for the latest
product status information.
The EP-15 Fluid Level sensor.
Blue female NMEA
2000 connector
Smart
module
Sending unit
connections:
red lead and
black lead.
2
The EP-15 consists of a smart module with a blue female locking cable
connector on one end and two bare wires on the other. The cable length
from the connector to the smart module is 18 inches (46 cm) and from
the smart module to the bare wires is 10 feet (3 meters).
The smart module converts fluid level information received from the
sending unit (fluid level arm or potentiometer) to the NMEA 2000 data
format. This allows any digital gauge, sonar or GPS unit connected to
the NMEA 2000 network to display the fluid level.
The EP-15 sensor is most commonly used in fuel tanks, but it is
designed to monitor fluid levels in almost any situation, including live
wells, oil reservoirs, fresh water, gray water or black water tanks.
The EP-15 Fluid Level sensor, like the other Lowrance Electronic Probe
(EP) sensors, is designed only for use with a NMEA 2000 Network. It
must be connected to a NMEA 2000 network or it function.will not
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will also need a one-time purchase of a LowranceNET Node Kit.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2 foot (61
cm) extension cable, T connector, 120-ohm male terminator and 120-
ohm female terminator.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one refer to the "Setup and Installation of NEMA
2000 Networks, General Information" document (part number 988-
0154-172) included with your EP-15 sensor. If that document is missing
it can be downloaded free from the Lowrance web site.


Produkt Specifikationer

Mærke: Lowrance
Kategori: Ikke kategoriseret
Model: EP-15 Fluid Level

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowrance EP-15 Fluid Level stil et spørgsmål nedenfor, og andre brugere vil svare dig