Lowrance EP-65R Fluid Level Manual

Lowrance Ikke kategoriseret EP-65R Fluid Level

Læs gratis den danske manual til Lowrance EP-65R Fluid Level (52 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Lowrance EP-65R Fluid Level, eller vil du spørge andre brugere om produktet?

Side 1/52
1
Pub. 988-0154-372
EP-65R Fluid Level
Electronic Sensor
Installation, Configuration and Calibration Instructions
This document shows how to install an EP-65R Fluid Level sensor and
how to connect it to a NMEA 2000® network. It also provides
instructions on how to configure and calibrate your fluid level sensor
with Lowrance digital gauges (LMF-200 & LMF-400) and display units.
NMEA 2000 is the communication bus standard developed by the
National Marine Electronics Association (NMEA) for use in boats.
Lowrance has introduced the LowranceNet, a line of products that
can communicate over a NMEA 2000 network.
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. Decide where to install all
components before drilling any holes in your vessel.
Some sonar or GPS display units may require a software upgrade to
display NMEA 2000 data correctly. For free software upgrades or
additional information on the LowranceNet NMEA 2000 ® network
system, visit our web site, www.lowrance.com.
The EP-65R Fluid Level sensor.
NMEA 2000 red
cable connector
Smart
module
Sending unit
connections
red lead and
black lead.
2
The EP-65R consists of a smart module with a red cable connector on
one end and two bare wires on the other. The cable length from the
connector to the smart module is 18 inches (46 cm). The cable length
from the smart module to the bare wires is 10 feet (3 meters).
The smart module converts fluid level information received from the
sending unit (fluid level float) to the NMEA 2000 data format. This
allows any digital gauge, sonar or GPS unit connected to the NMEA
2000 network to display fluid level information.
The EP-65R fluid level sensor is designed to monitor fuel, live well, oil,
fresh water, waste water (gray water), and black water tanks.
The EP-65R Fluid Level, like the other LowranceNet Electronic Probe
(EP) sensors, is designed for use with a NMEA 2000 network. Your
sensor, however, is also compatible with LowranceNet blue connector
networks. It can be added to a blue connector network by using a red
female to blue female adapter cable. Your sensor MUST be connected
to a NMEA 2000 network or it WILL NOT function.
The NMEA 2000 red female to blue female adapter cable allows users
to add red connector devices to a blue connector network.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will need to purchase a LowranceNET Node Kit.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one, refer to the "Setup and Installation of
NMEA 2000 Networks, General Information" document (part number
988-0154-173) included with your EP-65R sensor. If that document is
missing it can be downloaded free from the Lowrance web site.


Produkt Specifikationer

Mærke: Lowrance
Kategori: Ikke kategoriseret
Model: EP-65R Fluid Level

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowrance EP-65R Fluid Level stil et spørgsmål nedenfor, og andre brugere vil svare dig