Luxul Epic 4 XBR-4500 Manual

Luxul Router Epic 4 XBR-4500

Læs gratis den danske manual til Luxul Epic 4 XBR-4500 (8 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 73 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 37 anmeldelser. Har du et spørgsmål om Luxul Epic 4 XBR-4500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Fo ld Fo ld Fo ld

READ ME FIRST

QUICK INSTALL GUIDE

Epic 4

Multi-WAN Gigabit Router

XBR-4500

Includes:



Multi-WAN Gigabit Router



Rack Mounting Ears (2)



Rubber Feet (4)



Power Cord

SETUP AND CONFIGURATION

Physical Installation

The Epic 4 can be rack-mounted or used as a desktop router. Install

it in a stable/safe place to avoid any possible damage. Make sure

there is adequate space around the router for ventilation and proper

heat dissipation. Avoid placement in direct sunlight. Do not place heavy

articles on the router and verify the ground connection of the outlet

is functioning properly.

Desktop/Shelf Installation

For desktop/shelf installation, attach the four rubber feet to the corner

indentations on the bottom of the router, then place it on

a solid, level platform.

Rack Installation

Use the included L brackets for convenient installation in a 19-inch server or

AV rack. As shown below, use four screws to attach the L-shaped brackets on

either side of the router, and mount the switch horizontally in the rack. Use

your desired hardware to ax the router supports to the rack.

Install Brackets for Rack-Mounting Attach Feet for Desktop Installation

Connecting Ethernet and Power

Before installing the router, test the Internet connection to verify that it

is functioning properly. Once Internet access is conﬁrmed to be working,

follow the steps below for installation and conﬁguration.

Connecting Ethernet

Luxul recommends Category-5, super Category-5 or Category-6 unshielded

twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best performance and

stable data transmission at 1000 Mbps, use Category-6 shielded twisted pair.

1. Connect the WAN: Connect the Internet cable from a telco/ISP

modem/router to the dedicated WAN 1 port on the router.

2. Connect the LAN: Connect a cable from the dedicated LAN 1 port on

the router to a switch, access point, or computer.

For best performance, and to maximize available ports, Luxul recommends

connecting all LAN devices to a Luxul switch, then connecting that switch

to the Epic 4 LAN port via a single Ethernet cable.

n NOTE: WAN 1 and LAN 1-4 are conﬁgured by default. The router

must be conﬁgured to provide additional WAN ports

n NOTE: Connect all LAN devices to a Luxul switch, then connect that

switch to the router for best results.

Connecting Power

Use the included power cable to connect the router to a surge-protected

outlet. The AC input socket and power switch are on the rear panel. The

built-in power supply supports 100~240VAC at 50/60Hz.

Sales

P: 801-822-5450

E: sales@luxul.com

Technical Support

P: 801-822-5450 Option 3

E: support@luxul.com

LUX-QIG-XBR-4500-v5 02221701

No part of this document may be modiﬁed or adapted in any way, for any purposes without permission in

writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the

right to make changes to any product to improve reliability, function, or design. No license is granted, either

expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license

only exists for equipment, circuits and subsystems contained in this or any Luxul product.

Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and

registered trademarks are property of their respective holders.

Produkt Specifikationer

Mærke:	Luxul
Kategori:	Router
Model:	Epic 4 XBR-4500
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	178.8 mm
Højde:	44.5 mm
Vægt:	1300 g
Produktfarve:	Sort
Generering af mobilnetværk:	Ikke understøttet
Strømforbrug (typisk):	12 W
Driftstemperatur (T-T):	32 - 104 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Ethernet WAN:	Ja
Netværksstandarder:	IEEE 802.1Q
VPN-support:	PPTP, L2TP, IPsec
Portvideresendelse:	Ja
DHCP-server:	Ja
Knap til nulstilling:	Ja
Servicekvalitet support (QoS):	Ja
Firewall:	Ja
Gæsteadgang:	Ja
LED-indikatorer:	LAN, Power, System, USB, WAN
USB version:	3.2 Gen 1 (3.1 Gen 1)
Antal USB-porte:	1
Bæredygtighedscertifikater:	CE, RoHS
Indgangsstrøm:	0.3 A
Firmware kan opgraderes:	Ja
Ethernet-grænsefladetype:	Gigabit Ethernet
Auto MDI/MDI-X:	Ja
VLAN understøttelse:	Ja
Stativ-montering:	Ja
Hastighed for videresendelse:	650 Mpps
Antal VPN-tunneler:	1
Gennemløb:	1 Gbit/sek.
Trafikkontrol:	Ja