Lyman Big Dipper Manual

Lyman Ikke kategoriseret Big Dipper

Læs gratis den danske manual til Lyman Big Dipper (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 97 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 49 anmeldelser. Har du et spørgsmål om Lyman Big Dipper, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Big Dipper

Casting Furnace

Operating

Instructions

Lyman Products Corp.

475 Smith St., Middletown, CT 06457

800-22-LYMAN

www.lymanproducts.com

The perfect companion to your Big Dipper Casting Furnace:

Lyman – the pioneer of reloading manuals introduces the

4th Edition of their popular Cast Bullet Handbook.

This is the first new Cast Bullet Handbook

from Lyman in 30 years!

It includes data for all Lyman Moulds, plus additional

data for select RCBS, Redding and Lee Moulds.

Written by well-known cast bullet authority,

Mike Venturino, this is the most up-to-date

and comprehensive cast bullet data available.

Operating Instructions

for the Big Dipper

WARNING: Melting lead and casting lead objects will expose

you and others in the area to lead, which is known to cause birth

defects, other reproductive harm and cancer.

REDUCING EXPOSURE:

Lead contamination, dust in the air and on your skin is invisible. Keep children

and pregnant women away during use until cleanup is complete. Risk can be

reduced (but not eliminated) with strong ventilation; washing hands immediately

after use of these products before eating or smoking; and careful cleaning of sur-

faces and floors with disposable wipes, after lead dust has had a chance to settle.

Use a lead specific cleaner with EDTA, or a high-phosphate detergent (like most

detergents sold for dishwashers) and bag used wipes for disposal.

CAUTIONS:

•Never allow moisture near molten lead as when introduced to lead, a

volatile steam explosion occurs and molten lead is sprayed not only out

over immediate area but also all over bullet caster. This moisture could be

introduced by a wet ladle or dipper, wet lead added to pot, condensation from

over head pipes, perspiration from bullet caster or many other ways.

• Never attempt to touch any of the furnaces surfaces as all are extremely hot.

• Always be sure unit is plugged into a properly grounded outlet.

•No casting should be done without proper safety wear. This includes: long

pants, long sleeve shirt, heat resistant gloves, eye protection, closed toe shoes.

• Keep all flammable materials away from casting area and do not operate on

flammable materials such as wood, paper or carpeting.

• Casting should be done in a well ventilated area. Avoid breathing in fumes or

dust that comes from the furnace.

• Keep children away from casting and reloading areas.

• Do not cast or reload if distracted.

•Do not smoke, eat or drink near or during the casting processes.

• Do not run dry without lead (except for initial warm-up period)

• Always wash hands after handling lead.

• Use caution when adding bullet metal to furnace or pot containing molten

metal to avoid splashing.

FURNACE SET-UP:

Before using your new furnace for the first time, we suggest you plug it into an

appropriate wall socket, turn knob to max and run empty for 10-15 minutes in a

well ventilated area to burn off preservatives. The unit will smoke a bit and

would be ideal in an outdoor area. The temperature of the furnace is controlled

by a precision rheostat. The furnace face plate is marked with graduations, when

the ideal casting temperature is found you can note the graduation mark for

future reference. The Lyman casting thermometer is particularly useful here.

MELTING COLD BULLET METAL:

Once the preservatives have been heated out of the furnace, load furnace with up

to 10 pounds of bullet metal. The pot contents will reach the designated tempera-

ture in approximately 15 minutes. Once up to temperature, the heating system

can be controlled to give various temp settings. The marks on the face plate are

for reference and do not relate to a specific temperature. You will need to experi-

ment with different settings in order to find the temperature that works best with

your bullet metal and mould combination. If you have a casting thermometer,

700 degrees F is a good starting point. Once you find your best temperature

make note of the reference mark so you can return to it for future casting ses-

sions.

When replenishing a near-empty pot, there is no need to adjust the control knob.

Add bullet material and allow pot 5 minutes to reach set temp and return to cast-

ing.

OPERATING YOUR FURNACE:

The Big Dipper furnace is designed for dipper casting. For best results, fill the

dipper with lead alloy and place the spout of the dipper against the pouring hole

in the mould’s sprue plate. Holding the mould and dipper together, slowly rotate

them to a vertical position with the dipper above the mould. This sequence will

give the most consistent castings.

PRESERVING YOUR FURNACE:

To realize the longest possible life from your furnace, follow these precautions:

1. Disconnect your furnace when it is not in use.

2. Do not operate furnace above rated voltage (115 Volts, AC)

3. For maximum life, run the furnace at the lowest temperature that provides sat-

isfactory casting. Establish appropriate temperatures by trial for each type of

bullet metal. Normally a 650-720 degrees F temperature range proves adequate

for most bullet casting.

Produkt Specifikationer

Mærke:	Lyman
Kategori:	Ikke kategoriseret
Model:	Big Dipper

Har du brug for hjælp?

Hvis du har brug for hjælp til Lyman Big Dipper stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Lyman Manualer

Lyman Case Trimm Xpress Manual

21 Maj 2023

Lyman Big Dipper Manual

6 Oktober 2022

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman AUTO300 WIFI Manual

1 August 2025

Navman AUTO550 DUAL Manual

1 August 2025

Newline DV-15023H Manual

1 August 2025

Navman MiVue 720 Manual

1 August 2025

Etna HF2008 Manual

1 August 2025

Grundig 40 VLE 7630 WP Manual

1 August 2025

Navman MiVue 600 DC Manual

1 August 2025

Navman MiVue 830DC Manual

1 August 2025

Navman MiVue 840 Manual

1 August 2025

Navman MiVue 880 DC Manual

1 August 2025