Mag-Torch MT525 Manual

Mag-Torch Loddemaskine MT525

Læs gratis den danske manual til Mag-Torch MT525 (8 sider) i kategorien Loddemaskine. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Mag-Torch MT525, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

ENG

FRA

ESP

POR

DANGER

PELIGRO

PERIGO

FIRE

INCENDIE

FUEGO

INCÊNDIO

EXPLOSION

EXPLOSIÓN

EXPLOSÃO

FUMES

VAPEURS

VAPORES

Instruction Manual

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and

birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. Wash hands after handling.

• Keep torch out of reach of children and anyone who has not read instructions. Do not point torch towards face, other persons or

ﬂammable objects. Never attempt to use torch as a cigarette lighter.

• Disconnect cylinder when not in use.

• Never attempt to modify the torch construction and never use unapproved accessories or fuels.

• Treat the torch as you would any ﬁne tool or instrument. Do not drop, throw, or otherwise abuse.

• Do not use a leaking, damaged or malfunctioning torch.

• Always wear safety glasses, protective gloves and use proper tools to handle hot work.

• Radiant energy can harm your eyes. Wear glasses having an appropriate lens shade number (see 29 CFR 1926.102) for the torch

operation being done; brazing and light cutting (3 or 4), medium cutting and light welding (4 or 5), heavy cutting and medium/heavy

welding (5-8).

• Work only in well-ventilated areas. Avoid the fumes from ﬂuxes, lead-based paint, and all metal heating operations. Be careful to avoid

fumes from cadmium plating and galvanized metal- remove these coatings in the area to be heated by ﬁling or sanding prior to heating.

• Never use torch to strip lead paint.

• Be careful when using the torch outdoors on sunny or windy days. Bright light makes it difﬁcult to see the torch’s ﬂame. Wind may carry

the torch’s heat back towards you or other areas not intended to be heated. Windy conditions may also cause sparks to be blown into

other areas with combustible materials.

• Heating a surface may cause heat to be conducted to adjoining surfaces that may be combustible or become pressurized when heated.

Always check to make sure no unintended parts or materials are being heated.

• Be aware that the tip of the torch can get extremely hot during use. Take precautions to protect yourself and others from accidental

burns.

• Never use the torch on or near combustibles. Be careful around motor vehicles or any gasoline-ﬁred products and beware of hidden fuel

lines and tanks.

• Always make certain the torch is placed on a level surface when connected to the fuel cylinder to reduce the risk of accidental tip over.

Be sure the torch is not pointed in a direction which could cause nearby objects to ignite when the torch is set down.

• Be careful not to overheat surrounding materials. Use a heat shield when necessary.

• Never leave the torch unattended when lit.

• Never attempt to repair or heat a gasoline tank, a chemical drum, an aerosol can, a compressed gas container that held ﬂammable liquid

or gas or any other chemical. Heating these is extremely dangerous, especially after they have been emptied because vapors may still be

in the container.

• Always have a ﬁre extinguisher and a bucket of water near the torch and work area.

• This torch consumes oxygen and must only be used in well ventilated areas. Do not use in a conﬁned space.

ASSEMBLY

1. Before attaching cylinder, make sure valve is closed by turning adjustment knob (1) clockwise until it stops Hand tighten only. Do not

force.

2. Hold torch so that burner tube (3) is pointed away from persons and ﬂammable materials. Thread gas cylinder into regulator/torch body.

Hand tight only. Do not force.

3. Check all joints and couplings periodically to insure against loose connections. With valve closed, without lighting, test all connections

with soapy water. If bubbles appear, gas is leaking and torch must be repaired or replaced. NEVER USE A FLAME TO CHECK FOR

LEAKS. Conduct this test in a well ventilated and spark-free area and where there are no open ﬂames.

DANGER

This torch is used with a ﬂammable product. Failure

to comply with these Warnings and Instructions may

result in an explosion or ﬁre that may cause property

damage, serious personal injury or death.

Read and comply with the instructions and warnings

in this manual and familiarize yourself with the torch

before lighting and using. Review instructions and

warnings periodically to maintain awareness. Do not

try to operate before reading instructions.

Torches are to be used only with hand held gas

cylinders speciﬁcally designated for use with torches.

DO NOT DISCARD THESE WARNINGS AND INSTRUCTIONS | NE PAS JETER CES AVERTISSEMENTS ET CES INSTRUCTIONS

NO DESECHE ESTAS ADVERTENCIAS E INSTRUCCIONES | NÃO DESCARTE ESTES AVISOS DE ATENÇÃO E INSTRUÇÕES

MT525

MT531

MT535

Produkt Specifikationer

Mærke:	Mag-Torch
Kategori:	Loddemaskine
Model:	MT525

Har du brug for hjælp?

Hvis du har brug for hjælp til Mag-Torch MT525 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Loddemaskine Mag-Torch Manualer

Mag-Torch MT565 Manual

28 August 2024

Mag-Torch MT525 Manual

28 August 2024

Loddemaskine Manualer

Nyeste Loddemaskine Manualer

Graphite Energy+ 58GE143 Manual

5 December 2025

Guede GIS 140 Manual

3 December 2025

Toolcraft SIG-290 Manual

26 November 2025

Proxxon Microflam MGS Manual

25 November 2025

Rothenberger Hot Pack 2 Manual

25 November 2025

Weller LT 4 Manual

14 November 2025

Rothenberger RoQuick 35957 Manual

12 November 2025

NEO Tools 19-157 Manual

15 Oktober 2025

NEO Tools 19-156 Manual

15 Oktober 2025

Toolcraft ST-150 HF Manual

2 Oktober 2025