Manson HCS-3202 Manual

Manson Batterioplader HCS-3202

Læs gratis den danske manual til Manson HCS-3202 (10 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Manson HCS-3202, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

HCS connected to Raspberry Pi demonstration scenario

*NOTE : You should have basic knowledge on Raspberry Pi operation so that you can understand

terms using in this document.

Demonstration idea

The idea of the demonstration is to connect two HCS power supply to Raspberry Pi. A driver is

installed into Raspberry Pi to connect USB device to Ethernet. The driver will map each USB port to

TCP connect port. For example USB 1 is mapped to TCP port 4001. Then remote control software can

connect to HCS power supply by using IP address of Raspberry Pi and port number for USB.

E.g. Raspberry Pi IP address : 192.168.1.100

USB port 1 map to TCP port 4001

The connection setup is 192.168.1.100:4001

A load, which can be LED or DC FAN, is used to connect to power supply output so that the voltage

and current reading can be recorded. We can use programming feature in our application to program

different voltage and current for the output. Then the application can record variation of voltage and

current.

The demonstration will use application on iPad which can set HCS output, get reading from it, has 20

steps programed output and monitoring the output.

Demonstration setup

Equipments list

1. HCS power supply x 2

2. Raspberry Pi B+ model

3. 12V DC Fan

4. 12 LED (around 5W)5. iPad

with iOS 7 or above

Setup Raspberry Pi B+

Software required :

i. Raspbian – OS for Raspberry Pi

ii. Manson driver for Raspberry Pi

iii. Winscp – File transfer tools to transfer driver to Raspberry Pi

1. It is recommended to buy SD card with pre-installed Raspbian directly from shop to simplify the

installation.

2. Configure SSH server in Raspberry Pi for file transfer from Windows.

- Open terminal in Raspberry Pi.

- Run command “raspi-config” in raspberry pi console to get following interface.

- Select “Advanced Options” to configure SSH

Produkt Specifikationer

Mærke:	Manson
Kategori:	Batterioplader
Model:	HCS-3202

Har du brug for hjælp?

Hvis du har brug for hjælp til Manson HCS-3202 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Manson Manualer

Manson HCS-3202 Manual

24 August 2024

Manson NTP-5561 Manual

24 August 2024

Manson NEP-8323 Manual

24 August 2024

Manson SDP-3660 Manual

24 August 2024

Manson NTP-5631 Manual

24 August 2024

Manson HCS-3102 Manual

24 August 2024

Manson SDP-3636 Manual

24 August 2024

Manson NTP-5521 Manual

24 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Joy-It SBC-Buck04-5V Manual

8 Oktober 2025

Ansmann APM1 Manual

8 Oktober 2025

Ansmann USB-C Wall Charger 130PD Manual

8 Oktober 2025

Kress KAC877E Manual

5 Oktober 2025

Socket Mobile DuraCase Manual

3 Oktober 2025

Gardol 20V/30 Manual

3 Oktober 2025

Toolcraft ALG-1000 Manual

2 Oktober 2025

Nitecore NB Plus Manual

2 Oktober 2025

Draper D20 55913 Manual

1 Oktober 2025

Draper 53489 Manual

1 Oktober 2025