Manson NTP-5521 Manual

Manson Batterioplader NTP-5521

Læs gratis den danske manual til Manson NTP-5521 (5 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Manson NTP-5521, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

NTP- / /5561 SWITCHING MODE POWER SUPPLY 5521 5531

USER MANUAL

Keep this manual in a safe place for quick reference at all times.

This manual contains important safety and operation instructions for correct use of the power

supply. Read through the manual and pay special attention to the markings and labels of this

unit and equipment to be connected.

Pay special attention to these two types of notices used in this manual

WARNING:

Failure to observe this warning may cause injury to persons and damage to power

supply or connected equipment.

CAUTION:

Failure to observe this warning may result in damage to equipment

and Improper functioning of the power supply.

WARNING:

1. Do not use this power supply near water.

2. Do not operate or touch this power supply with wet hands.

3. Do not open the casing of the power supply when it is connected to ac mains.

4. Refer all servicing to qualied service personnel only.

5. Before replacing the AC fuse at AC socket, nd out and clear up the cause rst.

6. Replace the AC fuse with the same type and rating as the original fuse.

7. The max. output voltage of Model NTP- is 60VDC, avoid touch the metal contact part of the 5561

output terminals.

CAUTION:

1. Use a grounded 3 pin AC source.

2. This unit is for indoor use only.

3. Do not operate or place this unit in a humid, dusty, in direct sunlight location or near any heat source.

4. Before plugging into local AC mains, check with the rating label at the back of the unit.

5. Do not block any ventilation openings of the unit.

6. This unit must be used within the specied rating, regular excessive continuous loading may cause

damage to the power supply.

7. The gauge size of input power cable must be at least 0.75mm

2 and the total length of power cable

must not exceed 3m.

OPERATION ENVIRONMENTAL CONDITION

• -80% R.H. 10

• Maximum relative humidity 80% for temperature up to 31°C decreasing linearly to 50% relative humidity at

40°C.

• Altitude up to 2000m

• Installation category: CAT 2

• Pollution degree: 2

• Mains supply voltage fluctuation up to ±10% of the normal voltage

INTRODUCTION

This series of 100W Switching Mode Power Supplies with Current Limiting Control is designed with the objectives

of high accuracy, compactness and easy portability. Rotary encoder tuning with MCU are used for voltage and

current control. 4 digit display LCD of voltage and current for high precision.

This power supply is ideal for trouble shooting circuit boards or devices which require two or three dierent input

voltages such as 3V or 5V, 12V and 1-36V. This power supply can provide 3 outputs at the same time.

All three outputs are fully isolated so dierent cross connections of 2 or 3 outputs can provide various fixed or

variable output voltages. Any output can be connected for positive or negative polarity. (See connection diagrams)

CONTROLS AND INDICATORS

1. Power Switch:

- Turns the power supply on o, when it is on the front display lights up. –

2. AC Input Socket with Fuse

3. Concealed Fuse box (ply open the cover to get to the fuse)

4. 3.3V/5VDC selection switch (for Aux output 1)

5. Output Voltage Tuning knob. (Quick push the knob to toggle the coarse and ne tuning)

6. Output Current Tuning knob. (Quick push the knob to toggle the coarse and ne tuning)

7. Output On/O push button

- For Main output: Quick push this button to turn the Main output ON/OFF

- For Main output & Aux outputs: Push and hold this button for 3 seconds to turn the Main and Aux outputs

OFF, quick push this button again to turn them ON

8. Main Output Terminal Positive (+) Red color.

9. Main Output Terminal Negative (-) Black color

10. Aux Output 1 Terminal Positive (+ Red color (3.3VDC or 5VDC selectable) )

11. Aux Output 1 Terminal Negative (-) Black color (3.3VDC or 5VDC selectable)

12. Aux Output 2 Terminal Positive (+ Red color (Fixed 12VDC) )

13. Aux Output 2 Terminal negative (- Black color (Fixed 12VDC) )

14. LCD Display panel showing:

- 4 digit voltmeter meter, (CV) constant voltage mode, (CC) constant current mode, , Am

- Output Terminal on/o state

- 2 digit Aux outputs Ammeter

15. Aux 1 output voltage indicator

16. Reserved (factory internal use only)

Produkt Specifikationer

Mærke:	Manson
Kategori:	Batterioplader
Model:	NTP-5521

Har du brug for hjælp?

Hvis du har brug for hjælp til Manson NTP-5521 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Manson Manualer

Manson HCS-3202 Manual

24 August 2024

Manson NTP-5561 Manual

24 August 2024

Manson NEP-8323 Manual

24 August 2024

Manson SDP-3660 Manual

24 August 2024

Manson NTP-5631 Manual

24 August 2024

Manson HCS-3102 Manual

24 August 2024

Manson SDP-3636 Manual

24 August 2024

Manson NTP-5521 Manual

24 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Joy-It SBC-Buck04-5V Manual

8 Oktober 2025

Ansmann APM1 Manual

8 Oktober 2025

Ansmann USB-C Wall Charger 130PD Manual

8 Oktober 2025

Kress KAC877E Manual

5 Oktober 2025

Socket Mobile DuraCase Manual

3 Oktober 2025

Gardol 20V/30 Manual

3 Oktober 2025

Toolcraft ALG-1000 Manual

2 Oktober 2025

Nitecore NB Plus Manual

2 Oktober 2025

Draper D20 55913 Manual

1 Oktober 2025

Draper 53489 Manual

1 Oktober 2025